Nissan Juke F15. Instruction — part 723
EXL-112
< REMOVAL AND INSTALLATION >
[XENON TYPE]
HIGH-MOUNTED STOP LAMP
Never damage the blind seal, so that it can be reused.
2. Remove high-mounted stop lamp mounting nuts and connector.
3. Pull high-mounted stop lamp toward vehicle upside, and then remove high-mounted stop lamp.
NISMO and NISMO RS
1. Remove rear spoiler. Refer to
EXT-49, "Removal and Installation"
.
2. Remove high-mounted stop lamp cover mounting bolts, and then remove high-mounted stop lamp cover.
3. Remove high-mounted stop lamp harness connector from rear spoiler.
4. Pull out high-mounted stop lamp, and then remove high-mounted stop lamp.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Seal packing cannot be reused.
LICENSE PLATE LAMP
EXL-113
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LICENSE PLATE LAMP
Exploded View
INFOID:0000000012201704
Removal and Installation
INFOID:0000000012201705
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-7, "Precautions for Removing Battery Terminal"
.
REMOVAL
1. While pressing the license plate lamp to direction right side, pull
it to direction outside and then remove it.
2. Disconnect license plate lamp connector.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000012201706
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-7, "Precautions for Removing Battery Terminal"
.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
1. Remove license plate lamp. Refer to
EXL-113, "Removal and Installation"
2. Rotate the bulb socket counterclockwise and unlock it.
1.
License plate lamp housing assembly
2.
Bulb
3.
License plate lamp bulb socket
: Pawl
JMLIA1219ZZ
JPLIA0364ZZ
EXL-114
< REMOVAL AND INSTALLATION >
[XENON TYPE]
LICENSE PLATE LAMP
3. Remove the bulb from the socket.
REAR FOG LAMP
EXL-115
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REAR FOG LAMP
Exploded View
INFOID:0000000012201707
REMOVAL
Removal and Installation
INFOID:0000000012201708
REMOVAL
1. Remove rear bumper fascia lower. Refer to
EXT-23, "Removal and Installation"
2. Remove rear fog lamp housing mounting nuts.
3. Remove rear fog lamp housing from the rear bumper fascia lower.
4. Remove rear fog lamp housing bracket from rear bumper fascia lower.
INSTALLATION
Installation is the reverse order of removal.
1.
Rear fog lamp housing
2.
Rear bumper fascia lower
3.
Rear fog lamp housing bracket
N·m (kg-m, in-lb)
: Vehicle front
JMLIA3677GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст