Nissan Juke F15. Instruction — part 826
WINDSHIELD GLASS
GW-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REMOVAL AND INSTALLATION
WINDSHIELD GLASS
Exploded View
INFOID:0000000012199888
JMKIA5587GB
GW-12
< REMOVAL AND INSTALLATION >
WINDSHIELD GLASS
Removal and Installation
INFOID:0000000012199889
REMOVAL
1. Remove front pillar garnish (LH and RH). Refer to
INT-18, "FRONT PILLAR GARNISH : Removal and
.
2. Remove inside mirror assembly. Refer to
MIR-16, "Removal and Installation"
CAUTION:
Replace inside mirror assembly after removal, when installing windshield glass.
3. Remove partially the headlining (front edge).
• For normal roof: Refer to
INT-27, "NORMAL ROOF : Removal and Installation"
INT-30, "SUNROOF : Removal and Installation"
.
4. Remove front wiper arm (LH and RH). Refer to
WW-50, "Removal and Installation"
5. Remove front fender cover (LH and RH). Refer to
.
6. Remove cowl top cover. Refer to
EXT-30, "Removal and Installation"
.
7. Apply protective tape around the windshield glass to protect the painted surface from damage.
8. Remove glass using piano wire or power cutting tool (A) and an inflatable pump bag (B) after removing
moldings.
NOTE:
Mark the body and the glass with matching marks if the windshield glass is reused.
WARNING:
Always wear safety glasses and heavy gloves to help prevent injuries.
CAUTION:
• Never use a cutting knife or power cutting tool when the glass is reused.
• Be careful not to scratch the glass when removing.
• Never set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
• The dam sealant rubber should be installed in position.
• Use a genuine Nissan Urethane Adhesive Kit (if available) or an equivalent and follow the instructions pro-
vided with it.
• Open a door window while the urethane adhesive is curing. This prevents the glass from being forced out by
passenger room air pressure when all door windows are closed.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive is completely
cured (approximately 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
1.
Windshield glass molding
2.
Dam rubber (upper)
3.
Upper clip
4.
Windshield glass
5.
Dam rubber (lower)
6.
Lower clip
7.
Mirror base
8.
Adhesive
9.
Roof panel
10.
Headlining assembly
11. Primer
12. Cowl top cover
13.
Cowl top panel
14. Instrument panel assembly
15. Front pillar finisher
16.
Body side outer panel
F
: Black print mark
Unit : mm (in)
: Always replace after every disassembly.
PIIB5779E
WINDSHIELD GLASS
GW-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Never let
them come in contact with the skin and eyes.
• Use in an open, well ventilated location. Never breathe the vapors. They may be harmful if inhaled.
Move immediately to an area with fresh air if affected by vapor inhalation.
• Driving the vehicle before the urethane adhesive is completely cured may affect the performance of
the windshield in an accident.
CAUTION:
• Perform adjustment of front wiper arms stop location. Refer to
.
• Never use an adhesive that is past its usable term. Shelf life of this product is limited to six months
after the date of manufacture. Adhere carefully to the expiration or manufacture date printed on the
box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Never leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for 24 hours or more or until the urethane adhesive is completely
cured. Curing time varies depending on temperature and humidity. The curing time increases under
lower temperature and lower humidity.
Inspection
INFOID:0000000012199890
REPAIRING WATER LEAKAGE FOR WINDSHIELD GLASS
Leakage can be repaired without removing the windshield glass.
Determine the extent of leakage if water is leaking between the urethane adhesive material and body or glass.
This can be done by applying water to the windshield area while pushing glass outward.
Apply primer (if necessary) and then urethane adhesive to the leakage point to stop the leakage.
GW-14
< REMOVAL AND INSTALLATION >
BACK DOOR WINDOW GLASS
BACK DOOR WINDOW GLASS
Exploded View
INFOID:0000000012199891
1.
Back door window glass
2.
Spacer
3.
Back door window glass holder
4.
Back door window glass molding
5.
Pivot seal
6.
Adhesive
7.
Primer
8.
Back door outer
9.
Back door inner
JMKIA6169GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст