Nissan Juke F15. Instruction — part 1148
SEC-116
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-37, "Removal and Installation"
NO
>> Repair or replace harness.
(+)
(–)
Continuity
IPDM E/R
Connector
Terminal
E15
48
Ground
Not existed
HEADLAMP FUNCTION
SEC-117
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
HEADLAMP FUNCTION
Component Function Check
INFOID:0000000012202218
1.
CHECK FUNCTION
1. Perform “HEAD LAMP(HI)” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CONSULT.
2. Check headlamps operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
SEC-117, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000012202219
1.
CHECK HEADLAMP FUNCTION
EXL-50, "Component Function Check"
EXL-162, "Component Function Check"
(Halogen type).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
.
>> INSPECTION END
Test item
Description
HEAD LAMP (HI)
ON
Headlamps (Hi)
Light
OFF
Do not light
SEC-118
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
HORN FUNCTION
HORN FUNCTION
Component Function Check
INFOID:0000000012202220
1.
CHECK FUNCTION
1. Perform “VEHICLE SECURITY HORN” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CON-
SULT.
2. Check the horn operation.
Is the operation normal?
YES
>> INSPECTION END
NO
>> Go to
SEC-118, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000012202221
1.
CHECK HORN FUNCTION
Check that horn functions properly using horn switch.
Do horns sound?
YES
>> GO TO 2.
NO
>> Check horn circuit. Refer to
2.
CHECK HORN CONTROL CIRCUIT
1. Disconnect horn relay.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and horn relay harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> INSPECTION END
Test item
Description
VEHICLE SECURITY HORN
ON
Horn
Sounds (for 0.5 sec)
IPDM E/R
Horn relay
Continuity
Connector
Terminal
Connector
Terminal
E13
34
E5
1
Existed
SECURITY INDICATOR LAMP
SEC-119
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SECURITY INDICATOR LAMP
Component Function Check
INFOID:0000000012202222
1.
CHECK FUNCTION
1. Perform “THEFT IND” in “ACTIVE TEST” mode of “IMMU” of “BCM” using CONSULT.
2. Check security indicator lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
SEC-119, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000012202223
1.
CHECK FUSE
1. Turn power switch OFF.
2. Check that the following fuse in the fuse block (J/B) is not blown.
Is the fuse blown (open)?
YES
>> Replace the blown fuse after repairing the cause of blowing.
NO
>> GO TO 2.
2.
CHECK SECURITY INDICATOR LAMP POWER SUPPLY CIRCUIT
1. Disconnect combination meter connector.
2. Check voltage between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK SECURITY INDICATOR LAMP SIGNAL
1. Connect combination meter connector.
2. Disconnect BCM connector.
3. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 5.
4.
REPLACE BCM
Test item
Description
THEFT IND
ON
Security indicator lamp
Illuminates
OFF
Does not illuminate
Signal name
Fuse No.
Battery power supply
11 (10 A)
(+)
(–)
Voltage (V)
(Approx.)
Combination meter
Connector
Terminal
M34
27
Ground
Battery voltage
(+)
(–)
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M68
23
Ground
Battery voltage
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст