Nissan Juke F15. Instruction — part 263
P182D AWD SOLENOID (LEFT)
DLN-57
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P182D AWD SOLENOID (LEFT)
DTC Logic
INFOID:0000000012199401
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION (1)
With CONSULT
1. Turn the ignition switch OFF to ON, and then wait for 5 seconds or more.
2. Turn the ignition switch OFF.
3. Turn the ignition switch ON, and then wait for 5 seconds or more.
4. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182D” detected?
YES
>> Proceed to
.
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION (2)
With CONSULT
1. Lift up the vehicle.
2. Start the engine, and run at idle for 1 second.
3. Stop the engine.
4. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182D” detected?
YES
>> Proceed to
.
NO
>> GO TO 4.
4.
PERFORM DTC CONFIRMATION (3)
With CONSULT
1. Drive the vehicle at 30 km/h (19 MPH) or less for approximately 1 minute.
2. Stop the vehicle.
3. Drive the vehicle at 30 km/h (19 MPH) or less for approximately 1 minute again.
4. Stop the vehicle.
5. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182D” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199402
1.
CHECK AWD SOLENOID CIRCUIT (1)
1. Turn the ignition switch OFF.
2. Disconnect AWD control module harness connector.
3. Check the resistance between AWD control module harness connector.
DTC
Display item
Malfunction detected condition
Possible cause
P182D
SOLENOID LEFT
Malfunction related to AWD solenoid
(left) has been detected.
• Internal malfunction of electric con-
trolled coupling (left)
• Malfunction of AWD solenoid (left)
power supply circuit (open or short)
• Malfunction of AWD control module
DLN-58
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P182D AWD SOLENOID (LEFT)
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK AWD SOLENOID CIRCUIT (2)
1. Disconnect rear final drive sub-harness connector.
2. Check the continuity between AWD control module harness connector and rear final drive sub-harness
connector.
3. Check the continuity between AWD control module harness connector and the ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the error-detected parts.
3.
CHECK REAR FINAL DRIVE SUB-HARNESS
1. Disconnect electric controlled coupling (left) harness connector.
2. Check the continuity between rear final drive sub-harness connector and electric controlled coupling (left)
harness connector.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace rear final drive sub-harness. Refer to
4.
CHECK AWD SOLENOID
Check AWD solenoid. Refer to
DLN-59, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> AWD solenoid (left) is malfunctioning. Replace electric controlled coupling (left). Refer to
145, "Removal and Installation"
.
5.
CHECK TERMINALS AND HARNESS CONNECTORS
1. Check AWD control module pin terminals for damage or loose connection with harness connector.
2. Check rear final drive sub-harness pin terminals for damage or loose connection with harness connector.
AWD control module
Condition
Resistance (Approx.)
Connector
Terminal
B47
23
24
10
°C (50°F)
2.55
Ω
20
°C (68°F)
2.65
Ω
30
°C (86°F)
2.76
Ω
AWD control module
Rear final drive sub-harness
Continuity
Connector
Terminal
Connector
Terminal
B47
23
B64
4
Existed
24
8
AWD control module
—
Continuity
Connector
Terminal
B47
23
Ground
Not existed
24
Rear final drive sub-harness
Electric controlled coupling (left)
Continuity
Connector
Terminal
Connector
Terminal
B84
4
B85
4
Existed
8
8
P182D AWD SOLENOID (LEFT)
DLN-59
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
3. Check electric controlled coupling (left) pin terminals for damage or loose connection with harness con-
nector.
Is the inspection result normal?
YES
>> Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
.
NO
>> Repair or replace the error-detected parts.
Component Inspection
INFOID:0000000012199403
1.
CHECK AWD SOLENOID
1. Turn the ignition switch OFF.
2. Disconnect electric controlled coupling (left) harness connector.
3. Check the resistance between electric controlled coupling (left) connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> AWD solenoid (left) is malfunctioning. Replace electric controlled coupling (left). Refer to
145, "Removal and Installation"
Electric controlled coupling (left)
Condition
Resistance (Approx.)
Terminal
4
8
10
°C (50°F)
2.55
Ω
20
°C (68°F)
2.65
Ω
30
°C (86°F)
2.76
Ω
DLN-60
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P182E AWD SOLENOID (RIGHT)
P182E AWD SOLENOID (RIGHT)
DTC Logic
INFOID:0000000012199404
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION (1)
With CONSULT
1. Turn the ignition switch OFF to ON, and then wait for 5 seconds or more.
2. Turn the ignition switch OFF.
3. Turn the ignition switch ON, and then wait for 5 seconds or more.
4. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182E” detected?
YES
>> Proceed to
.
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION (2)
With CONSULT
1. Lift up the vehicle.
2. Start the engine, and run at idle for 1 second.
3. Stop the engine.
4. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182E” detected?
YES
>> Proceed to
.
NO
>> GO TO 4.
4.
PERFORM DTC CONFIRMATION (3)
With CONSULT
1. Drive the vehicle at 30 km/h (19 MPH) or less for approximately 1 minute.
2. Stop the vehicle.
3. Drive the vehicle at 30 km/h (19 MPH) or less for approximately 1 minute again.
4. Stop the vehicle.
5. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P182E” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199405
1.
CHECK AWD SOLENOID CIRCUIT (1)
1. Turn the ignition switch OFF.
2. Disconnect AWD control module harness connector.
3. Check the resistance between AWD control module harness connector.
DTC
Display item
Malfunction detected condition
Possible cause
P182E
SOLENOID RIGHT
Malfunction related to AWD solenoid
(right) has been detected.
• Internal malfunction of electric con-
trolled coupling (right)
• Malfunction of AWD solenoid (right)
power supply circuit (open or short)
• Malfunction of AWD control module
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст