Nissan Juke F15. Instruction — part 262
P181E STEERING ANGLE SENSOR
DLN-53
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P181E STEERING ANGLE SENSOR
DTC Logic
INFOID:0000000012199393
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Turn the ignition switch OFF to ON.
2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P181E” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199394
1.
PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is DTC “C1143” detected?
YES
>> Proceed to
BRC-108, "Diagnosis Procedure"
NO
>> GO TO 2.
2.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P181E”
is detected, Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P181E
STR ANGLE SEN
Malfunction is detected in steering angle
sensor signal through CAN communica-
tion.
• Steering angle sensor
- Steering angle sensor error
- Malfunction of steering angle sensor
circuit
• Malfunction of AWD control module
• CAN communication line
DLN-54
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P181F INCOMPLETE CALIBRATION
P181F INCOMPLETE CALIBRATION
DTC Logic
INFOID:0000000012199395
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Turn the ignition switch OFF to ON.
2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P181F” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199396
1.
PERFORM WRITING UNIT CHARACTERISTICS
1. Erase self-diagnostic result for “ALL MODE AWD/4WD”.
2. Perform writing unit characteristics. Refer to
3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC except “P181F” detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS AGAIN
With CONSULT
Perform “DTC CONFIRMATION PROCEDURE” (self-diagnosis) again. Refer to
Is DTC “P181F” detected?
YES
>> Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
.
NO
>> Check AWD control module pin terminals for damage or loose connection with harness connector.
If any items are damaged, repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P181F
INCOMP CALIBRATION
When incomplete writing unit character-
istics of rear final drive is detected.
Writing unit characteristics is incom-
plete.
P1820 ENGINE SPEED SIGNAL
DLN-55
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P1820 ENGINE SPEED SIGNAL
DTC Logic
INFOID:0000000012199397
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
2. Stop the vehicle.
3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1820” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199398
1.
PERFORM ECM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ENGINE”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
(Except for NISMO
RS),
(For NISMO RS).
NO
>> GO TO 2.
2.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P1820”
is detected, Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P1820
ENGINE SPEED SIG
Malfunction is detected in engine speed
signal that is output from ECM through
CAN communication.
• ECM
• AWD control module
• CAN communication line
DLN-56
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P1829 ACCELERATOR PEDAL POSITION SENSOR
P1829 ACCELERATOR PEDAL POSITION SENSOR
DTC Logic
INFOID:0000000012199399
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
2. Stop the vehicle.
3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1829” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199400
1.
PERFORM ECM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ENGINE”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
(Except for NISMO
(For NISMO RS).
NO
>> GO TO 2.
2.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P1829”
is detected, Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P1829
THROTTLE POSI SEN
Malfunction is detected in accelerator
pedal position signal that is output from
ECM through CAN communication.
• ECM
• AWD control module
• CAN communication line
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст