Nissan Juke F15. Instruction — part 220
DLK-60
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR OPENER ACTUATOR
Is the inspection normal?
YES
>> Replace back door lock assembly.
NO
>> Repair or replace harness.
Back door lock assembly
Ground
Continuity
Connector
Terminal
D106
2
Existed
BACK DOOR OPENER SWITCH
DLK-61
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR OPENER SWITCH
Component Function Check
INFOID:0000000012196616
1.
CHECK FUNCTION
1. Select “TRUNK” of “BCM” using CONSULT.
2. Select “TR/BD OPEN SW” in “DATA MONITOR” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Back door opener switch is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196617
1.
CHECK BACK DOOR OPENER SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect back door opener switch connector.
3. Check signal between back door opener switch harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK BACK DOOR OPENER SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and back door opener switch harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harness.
Monitor item
Condition
Status
TR/BD OPEN SW
Back door opener switch
Pressed
ON
Released
OFF
(+)
(–)
Signal
(Reference value)
Back door opener switch
Connector
Terminal
D107
1
Ground
JPMIA0012GB
BCM
Back door opener switch
Continuity
Connector
Terminal
Connector
Terminal
M68
30
D107
1
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
30
Not existed
DLK-62
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR OPENER SWITCH
3.
CHECK BACK DOOR OPENER SWITCH GROUND CIRCUIT
Check continuity between back door opener switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK BACK DOOR OPENER SWITCH
DLK-62, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace back door opener switch.
5.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000012196618
1.
CHECK BACK DOOR OPENER SWITCH
1. Turn ignition switch OFF.
2. Disconnect back door opener switch connector.
3. Check continuity between back door opener switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace back door opener switch.
Back door opener switch
Ground
Continuity
Connector
Terminal
D107
2
Existed
Back door opener switch
Condition
Continuity
Terminal
1
2
Back door opener
switch
Pressed
Existed
Released
Not existed
BACK DOOR REQUEST SWITCH
DLK-63
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR REQUEST SWITCH
Component Function Check
INFOID:0000000012196619
1.
CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “REQ SW-BD/TR” in “DATA MONITOR” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Back door request switch is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196620
1.
CHECK BACK DOOR REQUEST SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect back door opener switch connector.
3. Check voltage between back door opener switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK BACK DOOR REQUEST SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and back door opener switch harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair harness or connector.
3.
CHECK BACK DOOR REQUEST SWITCH GROUND CIRCUIT
Check continuity between back door opener switch harness connector and ground.
Monitor item
Condition
Status
REQ SW-BD/TR
Back door request switch
Pressed
On
Released
Off
(+)
(–)
Voltage
(Approx.)
Back door opener switch
Connector
Terminal
D107
3
Ground
12 V
BCM
Back door opener switch
Continuity
Connector
Terminal
Connector
Terminal
M68
51
D107
3
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
51
Not existed
Back door opener switch
Ground
Continuity
Connector
Terminal
D107
4
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст