Nissan Juke F15. Instruction — part 221
DLK-64
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR REQUEST SWITCH
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK BACK DOOR REQUEST SWITCH
DLK-64, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace back door opener switch.
5.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000012196621
1.
CHECK BACK DOOR REQUEST SWITCH
1. Turn ignition switch OFF.
2. Disconnect back door opener switch connector.
3. Check continuity between back door opener switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace back door opener switch.
Back door opener switch
Condition
Continuity
Terminal
3
4
Back door request switch
Pressed
Existed
Released
Not existed
BUZZER (COMBINATION METER)
DLK-65
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BUZZER (COMBINATION METER)
Component Function Check
INFOID:0000000012196622
1.
CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “INSIDE BUZZER” in “ACTIVE TEST” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
Yes
>> Buzzer (combination meter) is OK.
No
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196623
1.
CHECK METER BUZZER CIRCUIT
WCS-40, "Component Function Check"
.
Is the inspection result normal?
Yes
>> GO TO 2.
No
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
.
>> INSPECTION END
Monitor item
Status
INSIDE BUZZER
Take Out
ON
Take away warning
Buzzer sounds
OFF
Buzzer does not sound
Key
ON
OFF position warning
Buzzer sounds
OFF
Buzzer does not sound
DLK-66
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR KEY CYLINDER SWITCH
DOOR KEY CYLINDER SWITCH
Component Function Check
INFOID:0000000012196624
1.
CHECK FUNCTION
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “KEY CYL LK SW”, “KEY CYL UN-SW” in “DATA MONITOR” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door key cylinder switch is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196625
1.
CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front door lock assembly (driver side) connector.
3. Check voltage between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR KEY CYLINDER SWITCH SIGNAL CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.
3. Check continuity between BCM harness connector and ground.
Monitor item
Condition
Status
KEY CYL LK-SW
Driver side door key cylinder
Lock
ON
Neutral / Unlock
OFF
KEY CYL UN-SW
Unlock
ON
Neutral / Lock
OFF
(+)
(–)
Voltage (V)
(Approx.)
Front door lock assembly (driver side)
Connector
Terminal
D38
5
Ground
8.0 - 8.5 V
6
Battery voltage
JPMIA0587GB
BCM
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M68
7
D38
5
Existed
8
6
DOOR KEY CYLINDER SWITCH
DLK-67
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK DOOR KEY CYLINDER SWITCH GROUND CIRCUIT
Check continuity between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK DOOR KEY CYLINDER SWITCH
DLK-67, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace front door lock assembly (driver side).
5.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000012196626
1.
CHECK DOOR KEY CYLINDER SWITCH
1. Turn ignition switch OFF.
2. Disconnect front door lock assembly (driver side) terminal.
3. Check continuity between front door lock assembly (driver side) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front door lock assembly (driver side).
BCM
Ground
Continuity
Connector
Terminal
M68
7
Not existed
8
Front door lock assembly (driver side)
Ground
Continuity
Connector
Terminal
D38
4
Existed
Front door lock assembly (driver side)
Condition
Continuity
Terminal
5
4
Driver side door key cylinder
Unlock
Existed
Neutral / Lock
Not existed
6
Lock
Existed
Neutral / Unlock
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст