Nissan Juke F15. Instruction — part 1158
DIAGNOSIS SENSOR UNIT
SR-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
DIAGNOSIS SENSOR UNIT
Exploded View
INFOID:0000000012199981
Removal and Installation
INFOID:0000000012199982
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Before disconnecting the air bag sensor unit harness connector, be sure to disconnect the each har-
ness connector of the air bag module and pre-tensioner seat belt to prevent air bag deployment by
static electricity and pre-tensioner seat belt operation.
• Never use the air tools or electric tools for servicing.
• When replacing the air bag diagnosis sensor unit, always check with the parts department for the lat-
est parts information. Installing an incorrect air bag diagnosis sensor unit may or may not cause the
air bag warning lamp to illuminate and may cause incorrect deployment of the supplemental air bags
and seat belt pre-tensioners in a collision resulting in serious personal injury or death.
REMOVAL
1. Always check the air bag diagnosis sensor unit ECU discriminated number (identification number) using
CONSULT.
2. Disconnect the each connector of all air bag modules and pre-tensioner seat belts.
1.
Diagnosis sensor unit
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JMHIA3047GB
SR-30
< REMOVAL AND INSTALLATION >
DIAGNOSIS SENSOR UNIT
3. Remove the center console assembly. Refer to
IP-24, "Removal and Installation"
4. Disconnect the diagnosis sensor unit harness connectors (A).
5. Remove the diagnosis sensor unit mounting bolts (B), and then
remove the diagnosis sensor unit.
CAUTION:
• Never impact the diagnosis sensor unit.
• Replace the diagnosis sensor unit if it has been dropped or
sustained an impact.
• Replace the diagnosis sensor unit of deployed SRS air bag and deployed SRS front seat belt pre-ten-
sioner.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never use the old bolts after removal, replace with the new bolts.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
or
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
• After replacing the air bag diagnosis sensor unit, confirm using CONSULT that the ECU discrimi-
nated number (identification number) of the new replacement air bag sensor unit matches the ECU
discriminated number (identification number) of the replaced (old) air bag diagnosis sensor unit.
NOTE:
If the ECU discriminated number of the new replacement air bag diagnosis sensor unit differs from the ECU
discriminated number of the replaced air bag diagnosis sensor unit, reconfirm the parts information and verify
that the correct air bag diagnosis sensor unit was installed.
JMHIA1624ZZ
JMHIA0009ZZ
SEAT BELT PRE-TENSIONER
SR-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SEAT BELT PRE-TENSIONER
Exploded View
INFOID:0000000012199983
Removal and Installation
INFOID:0000000012199984
For removal and installation procedures, refer to
SB-6, "SEAT BELT RETRACTOR : Removal and Installa-
.
SR-32
< REMOVAL AND INSTALLATION >
OCCUPANT DETECTION SYSTEM CONTROL UNIT
OCCUPANT DETECTION SYSTEM CONTROL UNIT
Exploded View
INFOID:0000000012199985
Removal and Installation
INFOID:0000000012199986
REMOVAL
1. Remove passenger seat assembly. Refer to
.
2. Remove occupant detection system control unit (1) fixing screws
(A).
3. Disconnect occupant detection system control unit harness con-
nector (B), and then remove occupant detection system control
unit.
INSTALLATION
Install in the reverse order of removal.
JMHIA2826ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст