Nissan Juke F15. Instruction — part 1157
CRASH ZONE SENSOR
SR-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
2. Pull back front center grille, it makes work space.
3. Remove the crash zone sensor fixing nuts (A), and then pull the
bracket (1) and crash zone sensor (2) for vehicle front.
4. Disconnect the crash zone sensor harness connector, and then remove crash zone sensor.
CAUTION:
• Never impact the crash zone sensor.
• Replace the crash zone sensor if it has been dropped or sus-
tained an impact.
• Replace the crash zone sensor of deployed driver air bag, deployed passenger air bag, seat belt pre-
tensioner and deployed lap pre-tensioner.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never use the old fixing nut after removal, replace with the new nut.
• Never damage the harness while installing.
• Always install normally aligning to the cutout hole, because performance of the crash zone sensor
excessively fluctuates according to the installation position.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA1617ZZ
JMHIA1618ZZ
JMHIA0009ZZ
SR-26
< REMOVAL AND INSTALLATION >
SATELLITE SENSOR
SATELLITE SENSOR
Exploded View
INFOID:0000000012199979
Removal and Installation
INFOID:0000000012199980
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or electric tools for servicing.
FRONT SATELLITE SENSOR
Removal
1. Remove the front door finisher. Refer to
INT-13, "Removal and Installation"
2. Remove sealing screen (lower side).
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
1.
Front satellite sensor
2.
Front door inner panel
3.
Satellite sensor bracket
4.
Center pillar inner panel
5.
Rear satellite sensor
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JMHIA1805GB
SATELLITE SENSOR
SR-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
3. Remove the front satellite sensor mounting nuts (A), and then
pull the front satellite sensor (1).
4. Disconnect the harness connector and then remove the front satellite sensor.
CAUTION:
• Never impact the front satellite sensor.
• Replace the front satellite sensor if it has been dropped or
sustained an impact.
• Replace the front satellite sensor of deployed side air bag module and deployed curtain air bag mod-
ule.
Installation
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never use the old fixing nuts after removal, replace with the new nuts.
• Never damage the harness while installing.
• Always install normally aligning to the cutout hole, because performance of the front satellite sensor
excessively fluctuates according to the installation position.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
REAR SATELLITE SENSOR
Removal
1. Remove the center pillar lower garnish. Refer to
INT-22, "CENTER PILLAR LOWER GARNISH : Removal
2. Remove the rear satellite sensor mounting nut (A), and then pull
the rear satellite sensor (1).
3. Disconnect the harness connector and then remove the rear satellite sensor.
JMHIA1806ZZ
JMHIA0009ZZ
JMHIA1620ZZ
SR-28
< REMOVAL AND INSTALLATION >
SATELLITE SENSOR
CAUTION:
• Never impact the rear satellite sensor.
• Replace the rear satellite sensor if it has been dropped or sus-
tained an impact.
• Replace the rear satellite sensor of deployed side air bag module and deployed curtain air bag mod-
ule.
Installation
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never use the old fixing nut after removal, replace with the new nut.
• Never damage the harness while installing.
• Always install normally aligning to the cutout hole, because performance of the rear satellite sensor
excessively fluctuates according to the installation position.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
or
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст