Nissan Juke F15. Instruction — part 738
EXL-172
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
TAIL LAMP CIRCUIT
2. Disconnect IPDM E/R connector and rear combination lamp connector.
3. Check continuity between IPDM E/R harness connector and rear combination lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK TAIL LAMP GROUND CIRCUIT
Check continuity between rear combination lamp harness connector and ground.
Is the inspection result normal?
YES-1 >> Stop lamp / tail lamp (Bulb side): GO TO 5.
YES-2 >> Tail lamp (LED side): Check the corresponding tail lamp harness, and if check result is normal,
replace the corresponding rear combination lamp. Refer to
EXL-220, "Removal and Installation"
.
NO
>> Repair or replace harness.
5.
CHECK STOP LAMP / TAIL LAMP BULB
Check the applicable stop lamp / tail lamp bulb.
Is the inspection result normal?
YES
>> Check the corresponding stop lamp / tail lamp bulb socket and harness. Repair or replace if nec-
essary.
NO
>> Repair or replace the corresponding stop lamp / tail lamp bulb. Refer to
.
IPDM E/R
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E14
44
B59
2
Existed
LH
B80
Rear combination lamp
—
Continuity
Connector
Terminal
RH
B59
3
Ground
Existed
LH
B80
LICENSE PLATE LAMP CIRCUIT
EXL-173
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LICENSE PLATE LAMP CIRCUIT
Component Function Check
INFOID:0000000012201752
1.
CHECK TAIL LAMP OPERATION
Check that the tail lamp is turned ON.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check tail lamp circuit. Refer to
EXL-171, "Component Function Check"
.
2.
CHECK LICENSE PLATE LAMP OPERATION
With CONSULT
1. Turn ignition switch ON.
2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.
3. With operating the test items, check that the license plate lamp is turned ON.
Without CONSULT
1. Start IPDM E/R auto active test. Refer to
PCS-12, "Diagnosis Description"
2. Check that the license plate lamp is turned ON.
Is the inspection result normal?
YES
>> License plate lamp circuit is normal.
NO
>> Refer to
EXL-173, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000012201753
1.
CHECK LICENSE PLATE LAMP POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and back door opener switch connector.
3. Check continuity between IPDM E/R harness connector and back door opener switch harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK LICENSE PLATE LAMP GROUND CIRCUIT
Check continuity between back door opener switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK LICENSE PLATE LAMP BULB
Check the applicable license plate lamp bulb.
Is the inspection result normal?
TAIL
: License plate lamp ON
Off
: License plate lamp OFF
IPDM E/R
Back door opener switch
Continuity
Connector
Terminal
Connector
Terminal
E14
44
D107
5
Existed
Back door opener switch
—
Continuity
Connector
Terminal
D107
6
Ground
Existed
EXL-174
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
LICENSE PLATE LAMP CIRCUIT
YES
>> Check the corresponding license plate lamp bulb socket and harness. Repair or replace if neces-
sary.
NO
>> Replace the corresponding license plate lamp bulb. Refer to
.
DAYTIME RUNNING LIGHT RELAY CIRCUIT
EXL-175
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DAYTIME RUNNING LIGHT RELAY CIRCUIT
Component Function Check
INFOID:0000000012201754
1.
CHECK DAYTIME RUNNING LIGHT OPERATION
With CONSULT
1. Select “HEAD LAMP” of “BCM” using CONSULT.
2. Select “DAYTIME RUNNING LIGHT” in “Active Test” mode.
3. With operating the test items, check that the daytime running light is turned ON [Headlamp (HI) at approx-
imately half illumination].
Is the inspection result normal?
YES
>> Daytime running light relay circuit is normal.
NO
>> Refer to
EXL-175, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000012201755
1.
CHECK DAYTIME RUNNING LIGHT RELAY FUSE
1. Turn ignition switch OFF.
2. Check that the following fuses are not blown (open).
Is the fuse blown (open)?
YES
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown (open).
NO
>> GO TO 2.
2.
CHECK DAYTIME RUNNING LIGHT RELAY POWER SUPPLY
1. Remove daytime running light relay.
2. Check voltage between daytime running light relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK DAYTIME RUNNING LIGHT RELAY
Check daytime running light relay. Refer to
EXL-176, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace daytime running light relay.
4.
CHECK DAYTIME RUNNING LIGHT RELAY CONTROL SIGNAL
With CONSULT
1. Install daytime running light relay.
2. Turn ignition switch ON.
3. Select “HEAD LAMP” of “BCM” using CONSULT.
4. Select “DAYTIME RUNNING LIGHT” in “Active Test” mode.
On
: Daytime running light ON [Headlamp (HI) at approximately half illumination]
Off
: Daytime running light OFF
Unit
Fuse No.
Capacity
Daytime running light relay
#24
10 A
+
-
Voltage
(Approx.)
Daytime running light relay
Connector
Terminal
E65
1
Ground
Battery voltage
5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст