Nissan Juke F15. Instruction — part 650
EM-154
< PRECAUTION >
[MR EXCEPT FOR NISMO RS MODELS]
PRECAUTIONS
• Use torque wrench to tighten bolts or nuts to specification.
• When tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with the
ones in center, then ones on inside and outside diagonally in this order. If the order of tightening is specified,
do exactly as specified.
• Replace with new gasket, packing, oil seal or O-ring.
• Thoroughly wash, clean, and air-blow each part. Carefully check engine oil or engine coolant passages for
any restriction and blockage.
• Avoid damaging sliding or mating surfaces. Completely remove foreign materials such as cloth lint or dust.
Before assembly, oil sliding surfaces well.
• After disassembling, or exposing any internal engine parts, change engine oil and replace oil filter with a new
one.
• Release air within route when refilling after draining engine coolant.
• After repairing, start the engine and increase engine speed to check engine coolant, fuel, engine oil, and
exhaust gases for leakage.
Parts Requiring Angle Tightening
INFOID:0000000012197333
• Use the angle wrench [SST: KV10112100 (BT8653-A)] for the final tightening of the following engine parts:
- Camshaft sprocket (INT) bolt
- Cylinder head bolts
- Main bearing cap bolts
- Connecting rod cap bolts
- Crankshaft pulley bolt (No the angle wrench is required as bolt flange is provided with notches for angle
tightening)
• Do not use a torque value for final tightening.
• The torque value for these parts are for a preliminary step.
• Ensure thread and seat surfaces are clean and coated with engine oil.
Liquid Gasket
INFOID:0000000012197334
REMOVAL OF LIQUID GASKET SEALING
• After removing mounting nuts and bolts, separate the mating sur-
face using the seal cutter [SST: KV10111100 (J-37228)] (A) and
remove old liquid gasket sealing.
CAUTION:
Never damage the mating surfaces.
• Tap the seal cutter [SST: KV10111100 (J-37228)] to insert it ,
and then slide it by tapping on the side as shown in the figure.
• In areas where the seal cutter [SST: KV10111100 (J-37228)] is dif-
ficult to use, lightly tap the parts using a plastic hammer to remove
it.
CAUTION:
If for some unavoidable reason tool such as a screwdriver is
used, never damage the mating surfaces.
LIQUID GASKET APPLICATION PROCEDURE
1. Using a scraper (A), remove old liquid gasket adhering to the liq-
uid gasket application surface and the mating surface.
• Remove liquid gasket completely from the groove of the liquid
gasket application surface, mounting bolts, and bolt holes.
2. Wipe the liquid gasket application surface and the mating sur-
face with white gasoline (lighting and heating use) to remove
adhering moisture, grease and foreign materials.
JPBIA0052ZZ
JPBIA0053ZZ
PRECAUTIONS
EM-155
< PRECAUTION >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
3. Attach liquid gasket tube to the tube presser (commercial ser-
vice tool).
Use Genuine Liquid Gasket or equivalent.
4. Apply liquid gasket without gaps to the specified location accord-
ing to the specified dimensions.
• If there is a groove for liquid gasket application, apply liquid
gasket to the groove.
• As for bolt holes , normally apply liquid gasket inside the
holes. Occasionally, it should be applied outside the holes.
Check to read the text of this instruction.
• Within five minutes of liquid gasket application, install the mat-
ing component.
• If liquid gasket protrudes, wipe it off immediately.
• Do not retighten mounting bolts or nuts after the installation.
• After 30 minutes or more have passed from the installation, fill
engine oil and engine coolant.
CAUTION:
If there are specific instructions in this instruction, observe them.
EMA0622D
: Groove
: Inside
JPBIA0010ZZ
EM-156
< PREPARATION >
[MR EXCEPT FOR NISMO RS MODELS]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000012197335
Tool number
(TechMate No.)
Tool name
Description
KV10111100
(J-37228)
Seal cutter
Removing parts with liquid gasket ap-
plied
KV10114400
(J-38365)
Heated oxygen sensor wrench
Loosening or tightening heated oxy-
gen sensor 2 (AWD models)
a: For 22 mm (0.87 in) width hexa-
gon nut
KV10113700
or
KV10117100
(J-3647-A)
Heated oxygen sensor socket
Loosening or tightening air fuel ratio
sensor 1
For 22 mm (0.87 in) width hexagon
nut
KV11103000
( — )
Pulley puller
Removing crankshaft pulley
KV10112100
(BT8653-A)
Angle wrench
Checking tightening angle
KV10116200
(J-26336-A)
Valve spring compressor
1. KV10115900
(J-26336-20)
Attachment
2. KV10109220
( — )
Adapter
Disassembling and assembling valve
mechanism
Part (1) is a component of
KV10116200 (J-26336-A), but Part (2)
is not so.
ZZA0013D
S-NT636
ZZA1007D
ZZA0010D
ZZA0120D
PBIC1650E
PREPARATION
EM-157
< PREPARATION >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
KV10107902
(J-38959)
Valve oil seal puller
Removing valve oil seal
KV10115600
(J-38958)
Valve oil seal drift
Installing valve oil seal
Use side A (G).
a: 20 (0.79) dia. d: 8 (0.31) dia.
b: 13 (0.51) dia. e: 10.7 (0.421)
c: 10.3 (0.406) dia. f: 5 (0.20)
H: Side B
Unit: mm (in)
KV11105210
(J-44716)
Stopper plate
Removing and installing crankshaft
pulley
ST16610001
(J-23907)
Pilot bushing puller
Removing pilot converter
KV10119600
( — )
Injector remover
Removing and installing fuel injector
KV101197S0
( — )
Injector seal drift set
Installing fuel injector seal
Tool number
(TechMate No.)
Tool name
Description
ZZA0015D
JPBIA0396ZZ
ZZA0009D
ZZA0046D
JPBIA3746ZZ
JPBIA3281ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст