Nissan Juke F15. Instruction — part 242
DLK-148
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR
BACK DOOR ASSEMBLY : Adjustment
INFOID:0000000012196724
Except for NISMO/NISMO RS models
JMKIB4167GB
1.
Back door assembly
2.
Bumper rubber (upper)
3.
Bumper rubber (lower)
4.
Back door hinge
5.
Back door striker
6.
TORX bolt
7.
Roof panel
8.
Rear combination lamp
9.
Back door glass
10. Rear bumper fascia
D.
Rear bumper fascia R end
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Body grease
BACK DOOR
DLK-149
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
For NISMO/NISMO RS models
Check the clearance and the surface height between back door and each part by seeing and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Except for NISMO RS models
Unit: mm (in)
JMKIA9210GB
1.
Back door assembly
2.
Bumper rubber (upper)
3.
Bumper rubber (lower)
4.
Back door hinge
5.
Back door striker
6.
TORX bolt
7.
Roof panel
8.
Rear combination lamp
9.
Back door glass
10. Rear bumper fascia
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Body grease
Portion
Standard
Difference
(LH/RH, MAX)
Roof panel – Back
door
A – A
E
Clearance
5.0 – 7.0 (0.197 – 0.276)
—
F Surface height
0.9 – 2.9 (0.035 – 0.114)
—
DLK-150
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR
For NISMO RS models
Unit: mm (in)
FITTING ADJUSTMENT PROCEDURE
1. Loosen back door striker mounting bolts.
2. Loosen back door hinge mounting nuts (back door side).
3. Adjust back door using back door striker and back door hinge to the specified value, as shown in the fol-
lowing table.
4. After adjustment tighten back door striker mounting bolts and back door hinge mounting nuts (back door
side) to the specified torque.
5. Screw bumper rubber (upper) into the stopper position (A), and
then loosen by a half turn.
6. Screw bumper rubber (lower) into the end position of threads.
CAUTION:
• After installation, apply touch-up paint (the body color) onto the head of back door hinge mounting
nuts.
• After adjusting, perform camera image calibration (with around view monitor). Refer to
"CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Work Procedure"
• After adjusting, perform rear view camera adjustment (with rear view camera). Refer to
BACK DOOR STRIKER ADJUSTMENT
Adjust back door striker so that it becomes parallel with back door lock insertion direction.
BACK DOOR STRIKER
BACK DOOR STRIKER : Removal and Installation
INFOID:0000000012196725
REMOVAL
Rear combination
lamp – Back door
glass
B – B G
Clearance
2.8 – 7.2 (0.110 – 0.283)
<2.0 (0.079)
Rear bumper fas-
cia – Back door
C – C
H
Clearance
6.0 – 10.0 (0.236 – 0.394)
—
I
Surface height
9.1 – 12.6 (-0.358 – 0.496)
—
Portion
Standard
Difference
(LH/RH, MAX)
Portion
Standard
Difference
(LH/RH, MAX)
Roof panel – Back
door
A – A
D
Clearance
5.0 – 7.0 (0.197 – 0.276)
—
E Surface height
0.9 – 2.9 (0.035 – 0.114)
—
Rear combination
lamp – Back door
glass
B – B F
Clearance
2.8 – 7.2 (0.110 – 0.283)
<2.0 (0.079)
Rear bumper fas-
cia – Back door
C – C
G
Clearance
6.0 – 10.0 (0.236 – 0.394)
—
H Surface height
(-0.5) – (+3.0) [(-0.020) – (+0.118)]
—
JMKIA5843ZZ
BACK DOOR
DLK-151
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1. Remove luggage rear plate. Refer to
INT-35, "LUGGAGE REAR PLATE : Removal and Installation"
2. Remove TORX bolts, and then remove back door striker.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, check back door open/close, lock/unlock operation.
• After installation, perform the fitting adjustment. Refer to
DLK-148, "BACK DOOR ASSEMBLY :
BACK DOOR HINGE
BACK DOOR HINGE : Removal and Installation
INFOID:0000000012196726
REMOVAL
1. Remove back door assembly. Refer to
DLK-145, "BACK DOOR ASSEMBLY : Removal and Installation"
2. Remove back door hinge mounting nuts (body side), and then remove back door hinge.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, check back door open/close, lock/unlock operation.
• After installation, perform the fitting adjustment. Refer to
DLK-148, "BACK DOOR ASSEMBLY :
• Check back door hinge rotating part for poor lubrication. If
necessary, apply body grease.
BACK DOOR STAY
BACK DOOR STAY : Removal and Installation
INFOID:0000000012196727
REMOVAL
1. Remove luggage side upper finisher and rear pillar cap. Refer to
INT-36, "LUGGAGE SIDE UPPER FIN-
ISHER : Removal and Installation"
.
2. Support the back door with the suitable material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the back door open when removing the
back door stay.
3. Remove back door stay mounting bolts (body side).
4. Remove the metal clip (3) located on the connection between
the back door stay (1) and the stud ball (2) (back door side) by
using a flat-bladed screwdriver (A).
CAUTION:
Be careful not to damage painted surface.
5. Remove back door stay (back door side).
JMKIA5659ZZ
JMKIA2255ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст