Nissan Juke F15. Instruction — part 1388
WW-48
< REMOVAL AND INSTALLATION >
FRONT WASHER NOZZLE AND TUBE
3. While pressing pawl (A) on the cowl top cover front side of front
washer nozzle (1), remove front washer nozzle from cowl top
cover.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
The spray positions differ, check that left and right nozzles are installed correctly.
Inspection and Adjustment
INFOID:0000000012197077
INSPECTION
Check valve Inspection
Check that air can pass through the hose by blowing forward (toward
the nozzle (1)), and check that air cannot pass through by sucking.
ADJUSTMENT
Washer Nozzle Spray Position Adjustment
Adjust spray positions to match the positions shown in the figure.
JPLIA0871ZZ
JMLIA1326ZZ
1.
Black printed frame line
: Spray area
: Target spray position
JMLIA1497ZZ
FRONT WASHER NOZZLE AND TUBE
WW-49
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Unit: mm (in)
Insert a needle or similar object (A) into the spray opening (1) and
move up/down and left/right to adjust the spray position.
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle
or small pin.
Spray position
H
L
X
Y
S
A
244 (9.61)
350 (13.78)
80 (3.15)
238 (9.37)
78 (3.07)
B
284 (11.18)
93 (3.66)
80 (3.15)
257 (10.12)
89 (3.50)
C
258 (10.16)
70.5 (2.78)
80 (3.15)
255 (10.04)
82 (3.23)
D
309 (12.17)
234 (9.21)
80 (3.15)
312 (12.28)
95 (3.74)
E
235 (9.25)
413 (16.26)
80 (3.15)
295 (11.61)
90 (3.54)
JPLIA0873ZZ
WW-50
< REMOVAL AND INSTALLATION >
FRONT WIPER ARM
FRONT WIPER ARM
Exploded View
INFOID:0000000012197078
Removal and Installation
INFOID:0000000012197079
REMOVAL
1. Operate front wiper to move it to the auto stop position.
2. Open the hood.
3. Disengage front wiper arm cap (1) fixing pawls with a remover
tool (A), and then remove front wiper arm cap from the wiper
arm (2).
4. Remove front wiper arm mounting nuts.
5. Raise front wiper arm, and then remove front wiper arm from the vehicle.
INSTALLATION
1.
Front wiper arm cap
2.
Front wiper arm LH
3.
Front wiper blade LH
4.
Front wiper arm RH
5.
Front wiper blade RH
6.
Front wiper drive assembly
: Pawl
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMLIA1732GB
: Pawl
: Vehicle front
JMLIA1164ZZ
FRONT WIPER ARM
WW-51
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
1. Clean wiper arm mount as shown in the figure to prevent nuts
from being loosened.
2. Operate front wiper motor to move the front wiper to the auto
stop position.
3. Adjust front wiper blade position. Refer to
4. Install front wiper arm by tightening the mounting nuts.
5. Inject the washer fluid.
6. Operate front wiper to move it to the auto stop position.
7. Check that the front wiper blades stop at the specified position.
8. Install front wiper arm caps.
Adjustment
INFOID:0000000012197080
WIPER BLADE POSITION ADJUSTMENT
Clearance between the end of cowl top cover/ front fender protector and the top of wiper blade center
Standard clearance
ELH0717D
1.
Front wiper arm LH
2.
Front wiper arm RH
3.
Cowl top cover
4.
Front fender cover
5.
Windshield glass assembly
JMLIA1334ZZ
R
: 37.7
± 7.5 mm (1.484 ± 0.295 in)
L
: 46.8
± 7.5 mm (1.843 ± 0.295 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст