Nissan Juke F15. Instruction — part 1017
PCS-12
< SYSTEM DESCRIPTION >
[IPDM E/R]
DIAGNOSIS SYSTEM (IPDM E/R)
DIAGNOSIS SYSTEM (IPDM E/R)
Diagnosis Description
INFOID:0000000012197158
AUTO ACTIVE TEST
Description
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Rear window defogger
• Front wiper motor
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
• Headlamp (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan
Operation Procedure
CAUTION:
Wiper arm interferes with hood when wiper is operated while wiper arm is in the raised position.
Always perform auto active test without setting wiper arm in the raised position. Always pour water on
front windshield glass in advance to auto active test so that damage on front windshield glass surface
is prevented.
1. Turn the ignition switch OFF.
2. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
CAUTION:
Close passenger door.
3. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
CAUTION:
Engine starts when ignition switch is turned ON while brake pedal is depressed.
4. After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
• When auto active test mode has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to
Inspection in Auto Active Test Mode
When auto active test mode is actuated, the following operation sequence is repeated 3 times.
Operation
sequence
Inspection location
Operation
1
Rear window defogger
10 seconds
2
Front wiper motor
LO for 5 seconds
→ HI for 5 seconds
3
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
10 seconds
4
Headlamp
LO for 10 seconds
→HI ON ⇔ OFF 5 times
5
A/C compressor (magnet clutch) ON
⇔ OFF 5 times
6
Cooling fan
50% duty for 5 seconds
→ 100% duty for 5 seconds
PCS
DIAGNOSIS SYSTEM (IPDM E/R)
PCS-13
< SYSTEM DESCRIPTION >
[IPDM E/R]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Concept of auto active test
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode
JMMIA0588GB
Symptom
Inspection contents
Possible cause
Rear window defogger does not operate
Perform auto active test.
Does the rear window defog-
ger operate?
YES
BCM signal input circuit
NO
• Rear window defogger
• Rear window defogger ground circuit
• Harness or connector between IPDM E/R
and rear window defogger
• IPDM E/R
Any of the following components do not
operate
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
• Headlamp (HI, LO)
• Front wiper motor
Perform auto active test.
Does the applicable system
operate?
YES
BCM signal input circuit
NO
• Lamp or motor
• Lamp or motor ground circuit
• Harness or connector between IPDM E/R
and applicable system
• IPDM E/R
A/C compressor does not operate
Perform auto active test.
Does the magnet clutch oper-
ate?
YES
• A/C amp. signal input circuit
• CAN communication signal between A/C
amp. and ECM
• CAN communication signal between ECM
and IPDM E/R
NO
• Magnet clutch
• Harness or connector between IPDM E/R
and magnet clutch
• IPDM E/R
PCS-14
< SYSTEM DESCRIPTION >
[IPDM E/R]
DIAGNOSIS SYSTEM (IPDM E/R)
CONSULT Function (IPDM E/R)
INFOID:0000000012197159
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Cooling fan does not operate
Perform auto active test.
Does the cooling fan operate?
YES
• ECM signal input circuit
• CAN communication signal between ECM
and IPDM E/R
NO
• Harness or connector between IPDM E/R
and cooling fan relay
• Harness or connector between IPDM E/R
and cooling fan control module.
• Harness or connector between cooling fan
control module and cooling fan motor
• Cooling fan motor
• Cooling fan relay
• Cooling fan control module
• IPDM E/R
Symptom
Inspection contents
Possible cause
Diagnosis mode
Description
Ecu Identification
Allows confirmation of IPDM E/R part number.
Self Diagnostic Result
Displays the diagnosis results judged by IPDM E/R.
Data Monitor
Displays the real-time input/output data from IPDM E/R input/output data.
Active Test
IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor
The results of transmit/receive diagnosis of CAN communication can be read.
Monitor Item
[Unit]
MAIN
SIGNALS
Description
RAD FAN REQ
[%]
×
Displays the value of the cooling fan speed request signal received from ECM via CAN
communication.
AC COMP REQ
[Off/On]
×
Displays the status of the A/C compressor request signal received from ECM via CAN
communication.
TAIL&CLR REQ
[Off/On]
×
Displays the status of the position light request signal received from BCM via CAN
communication.
HL LO REQ
[Off/On]
×
Displays the status of the low beam request signal received from BCM via CAN com-
munication.
HL HI REQ
[Off/On]
×
Displays the status of the high beam request signal received from BCM via CAN com-
munication.
FR FOG REQ
[Off/On]
×
Displays the status of the front fog light request signal received from BCM via CAN
communication.
FR WIP REQ
[Stop/1LOW/Low/Hi]
×
Displays the status of the front wiper request signal received from BCM via CAN com-
munication.
WIP AUTO STOP
[STOP P/ACT P]
×
Displays the status of the front wiper auto stop signal judged by IPDM E/R.
WIP PROT
[Off/BLOCK]
×
Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
IGN RLY1 -REQ
[Off/On]
Displays the status of the ignition switch ON signal received from BCM via CAN com-
munication.
PCS
DIAGNOSIS SYSTEM (IPDM E/R)
PCS-15
< SYSTEM DESCRIPTION >
[IPDM E/R]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
Test item
IGN RLY
[Off/On]
×
Displays the status of the ignition relay judged by IPDM E/R.
PUSH SW
[Off/On]
Displays the status of the push-button ignition switch judged by IPDM E/R.
INTER/NP SW
[Off/On]
Displays the status of the ignition power supply (M/T models) or shift position (CVT
models) judged by IPDM E/R.
ST RLY CONT
[Off/On]
Displays the status of the starter relay status signal received from BCM via CAN com-
munication.
IHBT RLY -REQ
[Off/On]
Displays the status of the starter control relay signal received from BCM via CAN com-
munication.
ST/INHI RLY
[Off/ ST ON/INHI ON/UNKWN]
Displays the status of the starter relay and starter control relay judged by IPDM E/R.
DETENT SW
[Off/On]
Displays the status of the CVT shift selector (detention switch) judged by IPDM E/R.
S/L RLY -REQ
[Off/On]
NOTE:
This item is indicated, but not monitored.
S/L STATE
[LOCK/UNLK/UNKWN]
NOTE:
This item is indicated, but not monitored.
DTRL REQ
[Off/On]
Displays the status of the daytime running light request signal received from BCM via
CAN communication.
NOTE:
This item is monitored only for the except for NISMO models.
OIL P SW
[Open/Close]
NOTE:
This item is indicated, but not monitored.
HOOD SW
[Off/On]
NOTE:
This item is indicated, but not monitored.
HL WASHER REQ
[Off/On]
NOTE:
This item is indicated, but not monitored.
THFT HRN REQ
[Off/On]
Displays the status of the theft warning horn request signal received from BCM via
CAN communication.
HORN CHIRP
[Off/On]
Displays the status of the horn reminder request signal received from BCM via CAN
communication.
Monitor Item
[Unit]
MAIN
SIGNALS
Description
Test item
Operation
Description
HORN
On
Operates horn relay for 20 ms.
REAR DEFOGGER
Off
OFF
On
Operates the rear window defogger relay.
FRONT WIPER
Off
OFF
Lo
Operates the front wiper relay.
Hi
Operates the front wiper relay and front wiper high relay.
MOTOR FAN
1
OFF
2
Transmits 50% pulse duty signal (PWM signal) to the cooling fan control module.
3
Transmits 75% pulse duty signal (PWM signal) to the cooling fan control module.
4
Transmits 100% pulse duty signal (PWM signal) to the cooling fan control module.
HEAD LAMP WASHER
On
NOTE:
This item is indicated, but cannot be tested.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст