Nissan Juke F15. Instruction — part 627
EM-62
< UNIT REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
ENGINE ASSEMBLY
UNIT REMOVAL AND INSTALLATION
ENGINE ASSEMBLY
2WD
2WD : Exploded View
INFOID:0000000012197282
M/T
Standard Models
CAUTION:
Check that the stud bolt (*2) is tight at the specified torque before tightening the mounting nut (*1)
shown in the figure. [Stud bolt (*2) may be loosened after loosening the mounting nut (*1)]
JSBIA4461GB
1.
Washer
2.
Upper torque rod (RH)
3.
Engine mounting insulator (RH)
4.
Rear torque rod bracket
5.
Rear torque rod
6.
Engine mounting bracket (LH)
7.
Engine mounting frame support (LH) 8.
Engine mounting insulator (LH)
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
ENGINE ASSEMBLY
EM-63
< UNIT REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
NISMO RS Models
CAUTION:
Check that the stud bolt (*2) is tight at the specified torque before tightening the mounting nut (*1)
shown in the figure. [Stud bolt (*2) may be loosened after loosening the mounting nut (*1)]
CVT
JSBIA4428GB
1.
Washer
2.
Upper torque rod (RH)
3.
Engine mounting insulator (RH)
4.
Rear torque rod bracket
5.
Rear torque rod
6.
Engine mounting bracket (LH)
7.
Engine mounting frame support (LH) 8.
Engine mounting insulator (LH)
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
EM-64
< UNIT REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
ENGINE ASSEMBLY
2WD : Removal and Installation
INFOID:0000000012197283
WARNING:
• Situate the vehicle on a flat and solid surface.
• Place chocks at front and back of rear wheels.
• Attach proper slingers and bolts described in PARTS CATALOG if engine slingers are not equipped.
CAUTION:
• Always be careful to work safely, avoid forceful or uninstructed operations.
• Never start working until exhaust system and coolant are cool enough.
• If items or work required are not covered by the engine section, refer to the applicable sections.
• Always use the support point specified for lifting.
• Use either 2-pole lift type or separate type lift as best you can. If board-on type is used for unavoid-
able reasons, support at the rear axle jacking point with a transmission jack or similar tool before
starting work, in preparation for the backward shift of center of gravity.
• For supporting points for lifting and jacking point at rear axle, refer to
NOTE:
1.
Washer
2.
Upper torque rod (RH)
3.
Engine mounting insulator (RH)
4.
Rear engine mounting bracket
5.
Rear torque rod
6.
Engine mounting insulator (LH)
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JSBIA4462GB
ENGINE ASSEMBLY
EM-65
< UNIT REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
Outline
Remove the engine and the transaxle assembly from the vehicle downward. Separate the engine and the tran-
saxle.
Preparation
1. Release fuel pressure. Refer to
2. Drain engine coolant from radiator. Refer to
CAUTION:
• Perform this step when the engine is cold.
• Never spill engine coolant on drive belts.
3. Remove the following parts.
• Engine undercover
• Front road wheels and tires
• Front fender protector (RH and LH): Refer to
• Drive belt: Refer to
EM-20, "Removal and Installation"
• Engine cover: Refer to
• Battery and battery tray: Refer to
.
• Air duct, and air cleaner case assembly and air cleaner body assembly: Refer to
.
• Radiator hose (upper and lower): Refer to
.
• Exhaust front tube: Refer to
.
• Radiator cooling fan assembly: Refer to
• Charger air cooler: Refer to
• Alternator: Refer to
STR-28, "MR16DDT : Removal and Installation"
Engine Room LH
1. Disconnect all connections of engine harness around the battery, and then temporarily secure the engine
harness into the engine side.
CAUTION:
Protect connectors using a resin bag against foreign materials during the operation.
2. Disconnect fuel feed hose quick connector. Refer to
3. Disconnect heater hoses. Refer to
.
4. Remove EVAP hoses. Refer to
.
5. Disconnect control cable from transaxle. (CVT models) Refer to
6. Disconnect control linkage from transaxle. (M/T models) Refer to
7. Disconnect clutch tube on transaxle side from clutch damper. (M/T models) Refer to
.
Engine Room RH
1. Disconnect vacuum hose from intake manifold. Refer to
.
2. Remove A/C compressor. Refer to
.
3. Remove ground cable at engine side.
Vehicle Underbody
1. Remove ground cable at transaxle side.
2. Remove drive shafts (RH and LH). Refer to
FAX-28, "2WD : Removal and Installation"
3. Remove rear torque rod.
4. Remove stabilizer connecting rod. Refer to
.
5. Remove front suspension member. Refer to
6. Preparation for the separation work of transaxle is as follows:
• Remove transaxle joint bolts which pierce at oil pan (upper) lower rear side. Refer to
.
Removal
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст