Nissan Juke F15. Instruction — part 912
IP-12
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
REMOVAL AND INSTALLATION
INSTRUMENT PANEL ASSEMBLY
Exploded View
INFOID:0000000012199206
JSJIA0096GB
INSTRUMENT PANEL ASSEMBLY
IP-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
Removal and Installation
INFOID:0000000012199207
WORK STEP
When removing instrument panel assembly, combination meter, audio unit, NAVI C/U, or center console
assembly take steps in the order shown by the numbers below.
1.
Front passenger air bag module
2.
Instrument panel assembly
3.
Instrument side finisher LH
4.
Combination meter
5.
Cluster lid A
6.
Push-button ignition switch
7.
Steering column upper cover (with-
out paddle shifter)
8.
Steering column lower cover (without
paddle shifter)
9.
Multi display unit
10. Instrument lower cover LH
11. Instrument lower cover RH
12. Glove box lid
13. Glove box dumper
14. Glove box assembly
15. Illumination lamp
16. Socket and bulb
17. Instrument side finisher RH
18. Switch panel
19. Sunload sensor
20. Optical sensor
21. Hazard switch
22. Instrument lower panel LH
23. Audio unit or AV C/U
24. Steering lock escutcheon (without In-
telligent Key)
25. Steering column mask (with Intelli-
gent Key)
26. Cluster lid C
27. Warning lamp
28. Socket knob
29. Inner socket
30. Socket ring
31. Cluster tray
32. USB connector
33. A/C controller (instruction A/C)
34. A/C finisher (instruction A/C)
35. Knob
36. Steering column upper cover (with
paddle shifter)
37. Steering column LH cover (with pad-
dle shifter)
38. Steering column lower cover (with
paddle shifter)
39. Steering column RH cover (with pad-
dle shifter)
: Clip
: Pawl
: Metal clip
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
, : Indicates that the part is connected at points with same symbol in actual vehicle.
PARTS
INSTRUMENT
PANEL
ASSEMBLY
COMBINATION
METER
AUDIO UNIT
or
NAVI C/U
CENTER
CONSOLE
ASSEMBLY
Shift lever knob (MT models only)
[1]
[1]
Console finisher assembly
[2]
[2]
Console rear finisher
[3]
[3]
Center console assembly fixing screws (rear side)
[4]
[4]
Instrument lower cover LH
[5]
[5]
Instrument lower cover RH
[6]
[6]
Center console assembly
[7]
[7]
Front body side welt LH
[8]
Front pillar garnish LH
[9]
Instrument side finisher LH
[10]
Instrument lower panel LH
[11]
[1]
Driver air bag module
[12]
Steering wheel assembly
[13]
Steering column covers
[14]
Spiral cable
[15]
Combination switch
[16]
IP-14
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
[]: Number indicates step in removal procedure.
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or
more.
REMOVAL
CAUTION:
When removing, always use a remover tool that is made of plastic.
1. Remove shift lever knob (MT models only). Refer to
TM-25, "Removal and Installation"
(6MT: RS6F94R)
TM-83, "Removal and Installation"
(6MT: RS6F52H).
2. Remove console finisher assembly.
1. Put selector lever in “N” position.
2. Loosen the parking brake lever stroke by turning the adjusting nut with a socket wrench. Refer to
4, "Inspection and Adjustment"
.
3. Lift up console finisher assembly in numerical order shown in the figure and disengage metal clips.
4. Remove console finisher assembly while pulling it towards vehicle rear.
Cluster lid A
[17]
[2]
Combination meter
[18]
[3]
Multi display unit (with auto A/C) or A/C finisher
(with instruction A/C)
[19]
[1]
A/C control fixing screws (with instruction A/C)
[20]
Cluster lid C
[21]
[2]
Audio unit or AV C/U
[22]
[3]
Harness connector of hazard switch
[23]
Cluster tray
[24]
Front body side welt RH
[25]
Front pillar garnish RH
[26]
Instrument side finisher RH
[27]
Glove box lid
[28]
Glove box assembly
[29]
Passenger air bag module
[30]
Switch panel
[31]
Instrument panel assembly
[32]
INSTRUMENT PANEL ASSEMBLY
IP-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
CAUTION:
• Be careful not for damaging parts in surrounding area.
• Remove metal clips slowly so that they are not damaged.
5. Disconnect seat heated switch harness connectors (with seat heated switch).
3. Remove console rear finisher.
1. Put front seat assembly (LH and RH) to frontmost position.
2. Pull back console rear finisher, and disengage the pawls
and metal clips.
4. Remove center console assembly fixing screws (A).
5. Remove instrument lower cover LH.
1. Put front seat assembly LH to rearmost position.
: Metal clip
JSJIA0057ZZ
: Pawl
: Metal clip
JMJIA4183ZZ
JMJIA4202ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст