Nissan Juke F15. Instruction — part 913
IP-16
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
2. Remove fixing clip (A).
3. Pull the instrument lower cover LH crosswise, and disen-
gage the pawl and metal clips.
CAUTION:
Remove pawl and metal clips slowly so that they are not
damaged.
6. Remove instrument lower cover RH.
1. Put front seat assembly RH to rearmost position.
2. Remove fixing clip (A).
3. Pull the instrument lower cover RH crosswise, and disen-
gage the pawl and metal clips.
CAUTION:
Remove pawl and metal clips slowly so that they are not
damaged.
7. Remove center console assembly.
1. Remove center console fixing screws (A).
2. Remove seat heated switch harness clip (with seat heated switch).
3. Lift up center console assembly back side.
CAUTION:
Be careful not for damaging parts in surrounding area.
8. Release front pillar portion of front body side welt LH. Refer to
INT-21, "BODY SIDE WELT : Removal and
.
9. Remove front pillar garnish LH. Refer to
INT-18, "FRONT PILLAR GARNISH : Removal and Installation"
.
10. Remove instrument side finisher LH.
1. Insert remover tool (A) between instrument side finisher LH
and instrument panel assembly to disengage the pawls as
shown in the figure.
2. Pull back instrument side finisher LH.
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
11. Remove instrument lower panel LH.
: Pawl
: Metal clip
JMJIA4551ZZ
: Pawl
: Metal clip
JMJIA4552ZZ
JMJIA4553ZZ
: Pawl
JMJIA4554ZZ
INSTRUMENT PANEL ASSEMBLY
IP-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
1. Remove hood opener and fuel lid opener lever. Refer to
DLK-155, "HOOD LOCK CONTROL CABLE
(with Intelligent Key System).
2. Remove fixing screw (A).
3. Pull back instrument lower panel LH, and then disengage
the pawls and metal clips.
4. Disconnect harness connectors and aspirator duct.
12. Remove driver air bag module. Refer to
SR-12, "Removal and Installation"
.
13. Remove steering wheel. Refer to
ST-9, "Removal and Installation"
14. Remove steering column covers.
without paddle shifter
1. Place the tilt to the lowest level.
2. Remove steering lock escutcheon (1). (without Intelligent
Key)
3. Remove fixing screws (A).
4. Pull up steering column upper cover (2), and then disen-
gage steering column upper cover fixing pawls.
5. Remove steering column upper cover.
6. Pull down the steering column lower cover (3), and then
remove steering column lower cover.
NOTE:
Disengage the pawls, and then remove steering lock escutch-
eon (4). (with Intelligent Key)
with paddle shifter
1. Place the tilt to the lowest level.
2. Remove fixing screws (A).
3. Pull up steering column upper cover (1), and then disen-
gage steering column upper cover fixing pawls.
4. Remove steering column upper cover.
5. Disengage fixing pawls, and then remove steering column
LH cover (2).
6. Disengage fixing pawls, and then remove steering column
RH cover (3).
7. Remove fixing screws (B).
8. Pull down the steering column lower cover (4), and then
remove steering column lower cover.
: Pawl
: Metal clip
JMJIA4556ZZ
: Pawl
JMJIB0706ZZ
: Pawl
JMJIB0702ZZ
IP-18
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
15. Remove spiral cable. Refer to
SR-15, "Removal and Installation"
.
16. Remove combination switch. Refer to
BCS-95, "Removal and Installation"
(with Intelligent Key System).
17. Remove cluster lid A.
1. Cover steering shaft with a shop cloth (A) to prevent dam-
age.
2. Pull back cluster lid A while holding the lower side and dis-
engage the metal clips underside.
3. Hold both upper sides of cluster lid A and pull it out towards
vehicle rear, and disengage pawl and metal clips topside.
4. Disconnect push-button ignition switch harness connector
and NATS antenna amp.harness connector. (with Intelligent
Key)
CAUTION:
Remove metal clips slowly so that they are not damaged.
18. Remove combination meter. Refer to
MWI-64, "Removal and Installation"
19. Remove multi display unit (with auto A/C) or A/C finisher (with instruction A/C).
Multi display unit (with auto A/C)
1. Apply protective tape (B) on instrument panel assembly (2) to protect it from damage.
: Pawl
: Metal clip
JMJIA4557ZZ
1.
Multi display unit (with auto A/C)
2.
Instrument panel assembly
(with auto A/C models)
3.
Intake door lever knob
4.
A/C finisher (with instruction A/C)
5.
Instrument panel assembly
(with instruction A/C models)
: Pawl
: Metal clip
JMJIA4558ZZ
INSTRUMENT PANEL ASSEMBLY
IP-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
2. Insert a remover tool (A) into the cutouts at the bottom of
multi display unit (1), then pull straight back to disengage
the pawls and metals clips.
3. Pull back multi display unit, and then disconnect harness connector.
A/C finisher (with instruction A/C)
1. Apply a protective tape (B) on instrument panel assembly (5) to protect it from damage.
2. Hold intake door lever knob (1) from upper side and lower
side, tilt it to the right and the left, and then disengage it
from intake door lever (2). Pull up intake door lever knob
and remove it from intake door lever.
3. Insert a remover tool (A) into the cutouts at the bottom of multi display unit (4), then pull straight back
to disengage pawls and metal clips.
4. Pull back A/C finisher.
20. Remove A/C control fixing screws (with Instruction A/C). Refer to
HAC-151, "Removal and Installation"
: Pawl
: Metal clip
JMJIA6909ZZ
JMJIA6910ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст