Nissan Juke F15. Instruction — part 1345
TM-570
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
WATER HOSE
WATER HOSE
Exploded View
INFOID:0000000012201266
Removal and Installation
INFOID:0000000012201267
REMOVAL
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter turn to
allow built-up pressure to escape. Carefully remove the cap by turning it all the way.
CAUTION:
Perform when the engine is cold.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Remove battery. Refer to
PG-105, "Removal and Installation"
.
2. Remove ECM and bracket as a set. Refer to
EC-1256, "Removal and Installation"
3. Remove CVT fluid charging pipe. Refer to
4. Remove water hoses.
5. Remove water tube assembly
INSTALLATION
1.
Thermostat housing
2.
Hose clamp
3.
Water hose A
4.
Clip
5.
Water tube assembly
6.
Water hose B
7.
Water hose C
8.
CVT oil warmer
9.
Transaxle assembly
10. Water outlet
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JSDIA6063GB
WATER HOSE
TM-571
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse hose clamp and clip.
• Securely install the water hose clip to the converter housing.
• Refer to the following when installing water hoses.
• Refer to the followings when installing hose clamp.
CAUTION:
Hose clamp should not interfere with the bulge of tube.
Inspection
INFOID:0000000012201268
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of engine coolant.
Hose (1)
Installation side
tube (2)
Direction of paint
mark
Hose insertion
depth (L)
Water hose A
Thermostat hous-
ing
Frontward
Hose end reaches
the 2-stage bulge.
CVT oil warmer
Water hose B
CVT oil warmer
Water tube as-
sembly
Water hose C
Water tube as-
sembly
Water outlet
Leftward
JSDIA2459ZZ
Hose (1)
Installation side tube
(2)
Hose clamp (3)
Direction of tab
Clamping position
(A)
Water hose A
Thermostat housing
Frontward
5 – 7 mm (0.20 –
0.28 in) from hose
end
CVT oil warmer
Water hose B
CVT oil warmer
Water tube assem-
bly
Water hose C
Water tube assem-
bly
Water outlet
Leftward
JSDIA2424ZZ
TM-572
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
FLUID COOLER HOSE
FLUID COOLER HOSE
Exploded View
INFOID:0000000012201269
Removal and Installation
INFOID:0000000012201270
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Remove fluid cooler hose A and B.
2. Remove fluid cooler tube A and B.
INSTALLATION
Note the followings and Installation is in the reverse order of removal.
CAUTION:
Never reuse hose clamp, and copper washer.
1.
Transaxle assembly
2.
Copper washer
3.
Fluid cooler tube B
4.
Hose clamp
5.
Fluid cooler hose B
6.
Fluid cooler tube A
7.
Fluid cooler hose A
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JSDIA6978GB
FLUID COOLER HOSE
TM-573
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Refer to the followings when installing CVT fluid cooler tubes.
• When installing fluid cooler tube A (1) and fluid cooler tube B (2) to
transaxle assembly, contact fluid cooler tubes stopper (A) and (B)
to transaxle case.
• Refer to the followings when installing fluid cooler hose.
• Refer to the followings when installing hose clamp.
CAUTION:
Hose clamp should not interfere with the bulge of tube.
Inspection
INFOID:0000000012201271
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
JSDIA6070ZZ
Hose (1)
Installation side tube (2)
Direction of paint mark
Hose insertion depth (L)
Fluid cooler hose A
CVT fluid cooler tube A
Frontward
(A): Hose end reaches the 2-stage bulge.
CVT oil warmer
(B): Hose end reaches the end of tube.
Fluid cooler hose B
CVT fluid cooler tube B
(A): Hose end reaches the 2-stage bulge.
CVT oil warmer
(B): Hose end reaches the end of tube.
JSDIA2355ZZ
Hose (1)
Installation side
tube (2)
Hose clamp (3)
Direction of tab
Clamping position
Fluid cooler
hose A
CVT oil warmer
Frontward
5 - 9 mm. (0.20 - 0.35
in) (A) from hose end
CVT fluid cooler
tube A
Fluid cooler
hose B
CVT oil warmer
CVT fluid cooler
tube B
JSDIA2424ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст