Nissan Juke F15. Instruction — part 280
REAR PROPELLER SHAFT
DLN-125
< REMOVAL AND INSTALLATION >
[REAR PROPELLER SHAFT: 3F
φ16-ETJ75]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• If constant velocity joint was bent during propeller shaft
assembly removal, installation, or transportation, its boot
(1) may be damaged. Wrap boot interference area to metal
part (2) with shop cloth or rubber to protect boot from
breakage.
• Since no retaining pin is included in sliding direction, the
boot may be damaged or dropped if the constant velocity
joint is slid out 25 mm (0.98 in) or more from the original
length. Therefore, handle constant velocity joint by slid-
ing it inward.
8. Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
• Align matching marks to install propeller shaft assembly to final drive and transfer companion flanges.
• To install, adjust front and rear position of mount bracket to avoid deflection (front-rear direction of the vehi-
cle) to the center bearing insulator.
• Perform inspection after installation. Refer to
• After tightening the bolts and nuts to the specification torque,
check that the bolts (3) on the flange side is tightened as shown in
the figure.
• If propeller shaft assembly or final drive assembly has been replaced, connect them as follows:
CAUTION:
Constant velocity joint of a new propeller shaft has a pre-
installed protector (1). Protector must be removed after
installing propeller shaft.
PDIA0982J
PDIA0983J
1.
Final drive assembly
2.
Propeller shaft assembly
JSDIA0196ZZ
JSDIA2289ZZ
DLN-126
< REMOVAL AND INSTALLATION >
[REAR PROPELLER SHAFT: 3F
φ16-ETJ75]
REAR PROPELLER SHAFT
1. Install propeller shaft (1) while aligning its matching mark (A) of
propeller shaft with the matching mark (B) of final drive (2) on
the joint as close as possible.
2. Temporary tighten bolts and nuts.
3. Press down propeller shaft (1) with matching mark (C) of final
drive (2) facing upward. Then tighten fixing bolts and nuts to the
specified torque.
Inspection
INFOID:0000000012199489
INSPECTION AFTER REMOVAL
Appearance
Check the propeller shaft for bend and damage. If damage is detected, replace propeller shaft assembly.
Propeller Shaft Runout
Check propeller shaft runout at measuring points with a dial indica-
tor. If runout exceeds specifications, replace propeller shaft assem-
bly.
• Propeller shaft runout measuring point (Point “ ”)
Journal Axial Play
JSDIA2287ZZ
JSDIA2288ZZ
Propeller shaft runout
: Refer to
.
JSDIA0193ZZ
: Front
Dimension
A: 542 mm (21.34 in)
B: 516.5 mm (20.33 in)
JSDIA2286ZZ
REAR PROPELLER SHAFT
DLN-127
< REMOVAL AND INSTALLATION >
[REAR PROPELLER SHAFT: 3F
φ16-ETJ75]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
As shown in the figure, while fixing yoke on one side, check axial
play of joint. If it is outside the standard, replace propeller shaft
assembly.
CAUTION:
Never disassemble joints.
Center Bearing
Check center bearing for noise and damage. If noise or damage is detected, replace propeller shaft assembly.
CAUTION:
Never disassemble center bearing.
INSPECTION AFTER INSTALLATION
After assembly, perform a driving test to check propeller shaft vibration. If vibration occurred, separate propel-
ler shaft from final drive or transfer. Reinstall companion flange by changing the phase between companion
flange and propeller shaft by the one bolt hole at a time. Then perform driving test and check propeller shaft
vibration again at each point.
Journal axial play
: Refer to
PDA0005D
DLN-128
< SERVICE DATA AND SPECIFICATIONS (SDS)
[REAR PROPELLER SHAFT: 3F
φ16-ETJ75]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
INFOID:0000000012199490
Propeller Shaft Runout
INFOID:0000000012199491
Unit: mm (in)
Journal Axial Play
INFOID:0000000012199492
Unit: mm (in)
Applied model
MR16DDT
Propeller shaft model
3F
φ16-ETJ75
Number of joints
3
Shaft length
1st (Spider to CVJ joint center)
1051 mm (41.38 in)
2nd (CVJ joint center to spider)
1000 mm (39.37 in)
Shaft outer diameter
1st
57 mm (2.500 in)
2nd
75 mm (2.95 in)
Type of journal bearings
(Non-disassembly type)
1st joint
Sell type
2nd joint
CVJ type
3rd joint
Shell type
Coupling method
Transfer side
Flange type
Rear final drive side
Flange type
Item
Limit
Propeller shaft runout
1.0 (0.031)
Item
Standard
Journal axial play
0 (0)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст