Nissan Juke F15. Instruction — part 974
LU-26
< SYSTEM DESCRIPTION >
[MR EXCEPT FOR NISMO RS MODELS]
SYSTEM
Engine Lubrication System Schematic
INFOID:0000000012197492
19.
Camshaft (INT)
20.
Camshaft sprocket (INT)
21
High-pressure fuel pump
22.
Camshaft (EXH)
JPBIA7037GB
OIL FILTER
LU-27
< BASIC INSPECTION >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
BASIC INSPECTION
OIL FILTER
Removal and Installation
INFOID:0000000012197493
REMOVAL
1. Remove oil filter using an oil filter wrench [SST: KV10115801]
(A).
CAUTION:
• Never get burned when engine or engine oil is heated.
• Use a shop cloth to absorb engine oil leakage when
removing.
• Never spill engine oil on the drive belt.
• Completely wipe away any engine oil spilled on the
engine and vehicle.
INSTALLATION
1. Eliminate foreign materials on the oil filter mounting surface.
2. Apply engine oil to the full circumference of the oil seal on a new
oil filter.
3. Screw in oil filter by hand until it contacts mounting surface on
the engine, and then screw in another 2/3 of a turn (A).
NOTE:
Tightening torque is 17.7 N·m (1.8 kg-m).
Inspection
INFOID:0000000012197494
INSPECTION AFTER INSTALLATION
1. Use the oil level gauge and check that the oil level is within the standard. Refer to
2. Start the engine. Check for fuel leakage.
3. Stop the engine. After stopping it, leave it for 10 minutes or more.
4. Check the engine oil level again. Fill with engine oil to adjust oil level if necessary. Refer to
: Vehicle front
JPBIA4450ZZ
SMA010
JPBIA0077ZZ
LU-28
< PERIODIC MAINTENANCE >
[MR EXCEPT FOR NISMO RS MODELS]
ENGINE OIL
PERIODIC MAINTENANCE
ENGINE OIL
Inspection
INFOID:0000000012197495
ENGINE OIL LEVEL AND CONTAMINATION
• Check engine oil level on a horizontal area before starting the engine. Wait for 10 minutes or more to check
oil level when the engine is started.
• Check that oil level is within the range between level L and level H.
• Fill with engine oil if oil level is outside the range.
• Check for white contamination or significant dirt in the engine oil.
• If the oil contains white contamination, the most likely cause is con-
tamination from engine coolant. Repair the cause of the contami-
nation.
• When inserting the oil level gauge into the oil level gauge guide,
apply engine oil to the rubber seal on the grip.
ENGINE OIL LEAKAGE
Check for engine oil leakage at the following parts.
• Oil pan
• Oil pan drain plug
• Oil filter
• Oil cooler
• Oil pressure sensor
• Oil temperature sensor
• Front cover
• VTC cover
• Intake valve timing control solenoid valve
• Intake valve timing intermediate-lock control solenoid valve
• Exhaust valve timing control solenoid valve
• Turbocharger assembly
• Turbocharger oil tube and hose
• Mating surface of cylinder head and rocker cover
• Mating surface of high-pressure fuel pump and camshaft bracket
• Mating surface of camshaft bracket and cylinder head
• Mating surface of cylinder block and cylinder head
• Crankshaft oil seal (front, rear)
ENGINE OIL PRESSURE CHECK
CAUTION:
Be careful not to get burned, as engine oil may be hot.
1. Remove the oil pressure sensor (1).
CAUTION:
Handle parts carefully and never subject them to impact.
2. Check the engine oil level.
A : Level must be within this range.
JPBIA0554ZZ
: Engine front
JSBIA5728ZZ
ENGINE OIL
LU-29
< PERIODIC MAINTENANCE >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
3. Install oil pressure gauge [SST: ST25051001 (J-25695-1)] (A)
and hose [SST: ST25052000 (J-25695-2)] (B).
4. Start engine and warm it up to normal operating temperature.
5. Check oil pressure with engine running under no-load.
NOTE:
When engine oil temperature is low, engine oil pressure becomes high.
If difference is extreme, check oil passage and oil pump for oil leakage.
6. After the inspections, install oil pressure sensor as follows:
a. Remove old liquid gasket adhering to oil pressure sensor and engine.
b. Apply liquid gasket and tighten oil pressure sensor to specification.
Use Genuine RTV Silicon Sealant or equivalent.
c. Check engine oil level.
d. After warming up engine, check that there is no leakage of engine oil with running engine.
e. Check engine oil level.
f.
After warming up engine, check that there is no leakage of engine oil with running engine.
Draining
INFOID:0000000012197496
WARNING:
• Be careful not to get burned, as engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin
contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.
1. Warm up the engine, and check for engine oil leakage from engine components. Refer to
2. Stop the engine and wait for 10 minutes.
3. Loosen oil filler cap.
4. Remove drain plug and then drain engine oil.
Refilling
INFOID:0000000012197497
1. Install drain plug with new drain plug washer. Refer to
.
CAUTION:
Be sure to clean drain plug and install with new drain plug washer.
2. Refill with new engine oil.
Engine oil specification and viscosity: Refer to
MA-11, "Fluids and Lubricants"
JPBIA0074ZZ
Engine oil pressure
: Refer to
Tightening torque
: Refer to
Tightening torque
: Refer to
Engine oil capacity
: Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст