Nissan Juke F15. Instruction — part 1081
RAX-16
< REMOVAL AND INSTALLATION >
[AWD]
REAR WHEEL HUB AND HOUSING
REMOVAL AND INSTALLATION
REAR WHEEL HUB AND HOUSING
Exploded View
INFOID:0000000012196561
Removal and Installation
INFOID:0000000012196562
REMOVAL
1. Remove tires with power tool. Refer to
WT-39, "Removal and Installation"
.
2. Remove wheel sensor. Refer to
BRC-150, "REAR WHEEL SENSOR : Removal and Installation"
.
3. Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to
BR-64, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
CAUTION:
Never depress brake pedal while brake caliper is removed.
4. Remove disc rotor. If disc rotor cannot be removed, remove as follows.
CAUTION:
• Parking brake completely in the released position.
• Put matching marks (A) on the wheel hub assembly and
the disc rotor before removing the disc rotor.
• Never drop disc rotor.
a. Fix the disc rotor with wheel nuts and remove the adjusting hole
plug.
1.
Axle housing
2.
Suspension arm
3.
Parking brake assembly
4.
Hub bolt
5.
Wheel hub assembly (Bearing-inte-
grated type)
6.
Disc rotor
7.
Plug
8.
Wheel hub lock nut
9.
Cotter pin
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JPDIG0202GB
JPDIG0066ZZ
REAR WHEEL HUB AND HOUSING
RAX-17
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
b. Using suitable tool, rotate adjuster (1) in the direction (A) to
retract and loosen brake shoe.
c. Remove disc rotor.
5. Remove cotter pin, and then loosen wheel hub lock nut with
power tool.
6. Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage wheel hub assembly from drive shaft.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be
careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for
joint sub-assembly, shaft and the other parts.
NOTE:
Use suitable puller, if wheel hub assembly and drive shaft can-
not be separated even after performing the above procedure.
7. Remove wheel hub lock nut.
8. Remove wheel hub assembly.
CAUTION:
Never remove parking brake assembly. Protect it from falling.
9. If axle housing need to be removed, remove drive shaft. Refer to
RAX-19, "Removal and Installation"
.
10. Remove hub bolts (1) from wheel hub assembly, using the ball
joint remover (A) (commercial service tool).
CAUTION:
• Remove hub bolt only when necessary.
• Never hammer the hub bolt to avoid impact to the wheel
hub assembly.
• Pull out the hub bolt in a direction perpendicular to the
wheel hub assembly.
11. Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Place a washer (A) as shown in the figure to install the hub bolts
(1) by using the tightening force of the nut (B).
CAUTION:
• Check that there is no clearance between wheel hub assem-
bly and hub bolt.
• Never reuse hub bolt.
• Never reuse wheel hub lock nut and cotter pin.
• Align the matching marks that have been made during removal
when reusing the disc rotor.
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000012196563
INSPECTION AFTER REMOVAL
Check wheel hub assembly for wear, cracks, and damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
JPDIG0204ZZ
JPDIG0070ZZ
JPDIF0299ZZ
JPDIF0300ZZ
RAX-18
< REMOVAL AND INSTALLATION >
[AWD]
REAR WHEEL HUB AND HOUSING
1. Check wheel sensor harness for proper connection.
BRC-148, "REAR WHEEL SENSOR : Exploded
.
2. Adjust parking brake operation (stroke). Refer to
PB-4, "Inspection and Adjustment"
.
3. Check wheel alignment. Refer to
4. Adjust neutral position of steering angle sensor. Refer to
.
REAR DRIVE SHAFT
RAX-19
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
REAR DRIVE SHAFT
Exploded View
INFOID:0000000012196564
Removal and Installation
INFOID:0000000012196565
REMOVAL
1. Remove tires with power tool. Refer to
WT-39, "Removal and Installation"
.
2. Remove wheel sensor. Refer to
BRC-150, "REAR WHEEL SENSOR : Removal and Installation"
.
3. Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to
BR-64, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
CAUTION:
Never depress brake pedal while brake caliper is removed.
4. Remove disc rotor. Refer to
RAX-16, "Removal and Installation"
5. Remove cotter pin, and then loosen wheel hub lock nut with power tool. Refer to
.
6. Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage wheel hub assembly from drive shaft.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be
careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for
joint sub-assembly, shaft and the other parts.
NOTE:
Use suitable puller, if wheel hub assembly and drive shaft can-
not be separated even after performing the above procedure.
7. Remove wheel hub lock nut.
8. Set jack under suspension arm.
1.
Circular clip
2.
Dust shield
3.
Housing
4.
Snap ring
5.
Ball cage/steel ball/inner race as-
sembly
6.
Stopper ring
7.
Boot band
8.
Boot
9.
Shaft
10. Joint sub-assembly
11. Sensor rotor
: Wheel side
: Fill NISSAN genuine grease or an equivalent.
: Always replace after every disassembly.
JPDIG0207ZZ
JPDIG0070ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст