Nissan Juke F15. Instruction — part 1173
B0093 FRONT DOOR SATELLITE SENSOR LH
SRC-57
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199609
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK DTC
Perform each inspection according to the displayed DTC.
Which DTC is displayed?
[B0093–86] >> GO TO 4.
Other than the above >> GO TO 2.
2.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO-1 >> Damage: Replace malfunctioning harness and connector.
NO-2 >> Disconnection or looseness: Securely lock the connector.
3.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace malfunctioning harness and connector.
4.
REPLACE FRONT DOOR SATELLITE SENSOR LH
1. Replace front door satellite sensor LH. Refer to
SR-26, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
SRC-58
< DTC/CIRCUIT DIAGNOSIS >
B0094 CRASH ZONE SENSOR
B0094 CRASH ZONE SENSOR
DTC Description
INFOID:0000000012199610
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B0094–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of crash zone sensor
• Internal malfunction of air bag diagnosis sensor unit
[B0094–23, B0094–24, B0094–25, B0094–28]
• Internal malfunction of crash zone sensor
• Internal malfunction of air bag diagnosis sensor unit
[B0094–81, B0094–93]
• Connection malfunction of harness or connector
• Internal malfunction of crash zone sensor
• Internal malfunction of air bag diagnosis sensor unit
[B0094–86]
• Air bag diagnosis sensor unit and crash zone sensor is different from the part specified
[B0094–88]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of crash zone sensor
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-10, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B0094–11
CRASH ZONE SENS
[Center Frontal Restraints
Sensor (Subfault)]
[GND-SHORT]
Crash zone sensor circuit is shorted to ground
B0094–23
[LOWER LIMIT ERR]
Lower limit value malfunction of crash zone sensor
B0094–24
[UPPER LIMIT ERR]
Upper limit value malfunction of crash zone sensor
B0094–25
[SELF-DIAG ERR]
Diagnosis malfunction of crash zone sensor
B0094–28
[OFFSET ERR]
Offset malfunction of crash zone sensor
B0094–81
[COMM ERR]
Communication malfunction of crash zone sensor
B0094–86
[UNMATCH]
Crash zone sensor is out of the specified specification
B0094–88
[OPEN]
Crash zone sensor circuit is open
B0094–93
[RESET]
Reset malfunction of crash zone sensor
B0094 CRASH ZONE SENSOR
SRC-59
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199611
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK DTC
Perform each inspection according to the displayed DTC.
Which DTC is displayed?
[B0094–86]>>GO TO 4.
Other than the above>>GO TO 2.
2.
CHECK HARNESS CONNECTOR
Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?
YES
>> GO TO 3.
NO–1 >> Damage: Replace malfunctioning harness and connector.
NO–2 >> Disconnection or looseness: Securely lock the connector.
3.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace malfunctioning harness and connector.
4.
REPLACE CRASH ZONE SENSOR
1. Replace crash zone. Refer to
SR-24, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to
SR-24, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
SRC-60
< DTC/CIRCUIT DIAGNOSIS >
B0096 B-PILLAR SATELLITE SENSOR
B0096 B-PILLAR SATELLITE SENSOR
DTC Description
INFOID:0000000012199612
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B0096–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
[B0096–23, B0096–24, B0096–25, B0096–28]
• Internal malfunction of satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
[B0096–81, B0096–93]
• Connection malfunction of harness or connector
• Internal malfunction of satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
[B0096–86]
• Air bag diagnosis sensor unit and satellite sensor RH is different from the part specified
[B0096–88]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-10, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B0096–11
B-PILLAR SAT SEN RH
[Right Frontal Restraints
Sensor 1(Subfault)]
[GND-SHORT]
Satellite sensor RH circuit is shorted to ground
B0096–23
[LOWER LIMIT ERR]
Lower limit value malfunction of satellite sensor RH
B0096–24
[UPPER LIMIT ERR]
Upper limit value malfunction of satellite sensor RH
B0096–25
[SELF-DIAG ERR]
Diagnosis malfunction of satellite sensor RH
B0096–28
[OFFSET ERR]
Offset malfunction of satellite sensor RH
B0096–81
[COMM ERR]
Communication malfunction of satellite sensor RH
B0096–86
[UNMATCH]
Satellite sensor RH is out of the specified specification
B0096–88
[OPEN]
Satellite sensor RH circuit is open
B0096–93
[RESET]
Reset malfunction of satellite sensor RH
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст