Nissan Juke F15. Instruction — part 746
EXL-204
< PERIODIC MAINTENANCE >
[HALOGEN TYPE]
FRONT FOG LAMP AIMING ADJUSTMENT
FRONT FOG LAMP AIMING ADJUSTMENT
Description
INFOID:0000000012201779
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the trunk
room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.).
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
• Turn the aiming adjusting screw for adjustment.
• For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.
Aiming Adjustment Procedure
INFOID:0000000012201780
1. Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2. Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.
3. Start the engine. Turn the front fog lamp ON.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
4. Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and (A) becomes 150 mm (5.91 in).
A: UP
B: DOWN
JMLIA1249ZZ
FRONT FOG LAMP AIMING ADJUSTMENT
EXL-205
< PERIODIC MAINTENANCE >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Front fog lamp light distribution on the screen
JPLIA0008ZZ
A
: Cutoff line
B
: High illuminance area
H
: Horizontal center line of front fog lamp
V
: Vertical center line of front fog lamp
X
: Cutoff line height
EXL-206
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
HEADLAMP
REMOVAL AND INSTALLATION
HEADLAMP
Exploded View
INFOID:0000000012201781
REMOVAL
DISASSEMBLY
1.
Headlamp assembly
: Vehicle front
: N·m (kg-m, in-lb)
JMLIA5396GB
HEADLAMP
EXL-207
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Removal and Installation
INFOID:0000000012201782
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-119, "Precautions for Removing Battery Terminal"
REMOVAL
1. Remove front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
2. Remove headlamp mounting bolts.
3. Pull out headlamp assembly forward the vehicle, and then disconnect the connector before removing the
headlamp assembly.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000012201783
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-119, "Precautions for Removing Battery Terminal"
• After installing the bulb, install the back cover and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
1.
Headlamp assembly
2.
Halogen bulb (LO)
3.
Back cover A
4.
Halogen bulb (HI)
5.
Back cover B
: Vehicle front
JMLIA5398ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст