Nissan Juke F15. Instruction — part 745
EXL-200
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT
TURNED ON
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT
TURNED ON
Description
INFOID:0000000012201773
The parking, license plate, side marker and tail lamps are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000012201774
1.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK POSITION LIGHT REQUEST SIGNAL
With CONSULT
1. Turn ignition switch ON.
2. Select “TAIL & CLR REQ” in “Data Monitor” mode of “IPDM E/R” using CONSULT.
3. With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> Perform the tail lamp diagnosis. Refer to
EXL-171, "Component Function Check"
.
NO
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
Monitor item
Condition
Monitor status
TAIL & CLR REQ Lighting switch
1ST
On
OFF
Off
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
EXL-201
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
Description
INFOID:0000000012201775
Both side front fog lamps are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000012201776
1.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK FRONT FOG LIGHT REQUEST SIGNAL
With CONSULT
1. Turn ignition switch ON.
2. Select “FR FOG REQ” in “Data Monitor” mode of “IPDM E/R” using CONSULT.
3. With operating the front fog lamp switch, check the monitor status.
Is the inspection result normal?
YES
>> Perform the front fog lamp diagnosis. Refer to
EXL-180, "Component Function Check"
NO
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
Monitor item
Condition
Monitor status
FR FOG REQ
Front fog lamp switch
(With lighting switch 1ST)
ON
On
OFF
Off
EXL-202
< PERIODIC MAINTENANCE >
[HALOGEN TYPE]
HEADLAMP AIMING ADJUSTMENT
PERIODIC MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
Description
INFOID:0000000012201777
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the trunk
room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.).
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
Aiming Adjustment Procedure
INFOID:0000000012201778
1. Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
JMLIA6147ZZ
A. Headlamp RH (UP/DOWN) adjustment screw B.
Headlamp LH (UP/DOWN) adjustment screw
: Vehicle front
Adjustment screw
Screw driver rotation
Facing direction
A
Headlamp LH (UP/DOWN)
Clockwise
DOWN
Counterclockwise
UP
B
Headlamp RH (UP/DOWN)
Clockwise
DOWN
Counterclockwise
UP
HEADLAMP AIMING ADJUSTMENT
EXL-203
< PERIODIC MAINTENANCE >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
2. Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the headlamp center and the screen.
3. Start the engine. Turn the headlamp (LO) ON.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
4. Measure the distance (X) between the horizontal center line of headlamp (H) and the cutoff line (A) within
the light axis measurement range (R) from the vertical center line ahead of headlamp (V).
Low beam distribution on the screen
5. Adjust the cutoff line height (X) with the aiming adjustment screw so as to enter in the adjustment range
(M–N) according to the horizontal center line of headlamp (H).
unit: mm (in)
Side view
Light axis measurement range (R)
: 350
± 175 mm (13.78 ± 6.89 in)
JSLIA0005ZZ
Horizontal center line of headlamp (H)
Highest cutoff line height (M)
Lowest cutoff line height (N)
700 (27.56) or less
4 (0.16)
30 (1.18)
701(27.60) – 800 (31.50)
4 (0.16)
30 (1.18)
801 (31.54) or more
17 (0.67)
44 (1.73)
JSLIA0006ZZ
Distance between the headlamp center and the screen (L)
: 10 m (32.8 ft)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст