Nissan Juke F15. Instruction — part 999
MWI-18
< SYSTEM DESCRIPTION >
SYSTEM
NOTE:
• Current fuel consumption on the information display is updated approximately every 0.5 seconds.
• Current fuel consumption on the information display shows 0 l/100km (0 mpg) when vehicle speed is 0 km/h
(0 MPH).
Average Fuel Consumption
The combination meter calculates average fuel consumption based on the following signals, and the calcu-
lated value is displayed on the information display.
NOTE:
• Average fuel consumption on the information display is updated approximately every 30 seconds.
• Soon after a reset or when the ignition switch is turned ON right after battery removal and installation, “
−−−”
is displayed until after a travel of 30 seconds and approximately 500 m (0.31 mile).
Distance to Empty
The combination meter calculates distance to empty based on the following signals, and the calculated value
is displayed on the information display.
NOTE:
• Distance to empty on the information display is updated approximately every 30 seconds.
• When the ignition switch is turned ON right after battery removal and installation, “
−−−” is displayed until after
a travel of 30 seconds.
• The indicated values may not match each other when refueling with the ignition switch ON.
Torque Distribution Indicator
DLN-12, "Torque Distribution Indicator"
INTERRUPT INDICATION
• The combination meter displays an interrupt regarding a warning, alert, and maintenance on the information
display, based on signals received from each unit and switch.
• When conditions are satisfied, the normal screen switches to a warning screen to display an interrupt.
Meter Illumination Level
The combination meter displays the illuminance level of the back light on the information display by turning the
meter control switch.
Fuel Filler Cap Warning
Signal name
Signal path
Ignition signal
—
Fuel consumption monitor signal
ECM
Combination
meter
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
Signal name
Signal path
Ignition signal
—
Fuel consumption monitor signal
ECM
Combination
meter
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
Signal name
Signal path
Ignition signal
—
Fuel level sensor signal
Fuel level sensor unit
Combination meter
Fuel consumption monitor signal
ECM
Combination
meter
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
MWI
SYSTEM
MWI-19
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• The combination meter judges showing/hiding of “fuel filler cap warning”, according to the signals below:
• For further information, refer to
EC-62, "FUEL FILLER CAP WARNING SYSTEM : System Description"
(MR
FOR NISMO RS MODELS) or
EC-652, "FUEL FILLER CAP WARNING SYSTEM : System Description"
(MR
EXCEPT FOR NISMO RS MODELS).
Low Tire Pressure Warning
• The combination meter judges showing/hiding of “low tire pressure warning”, according to the signals below:
• For further information, refer to
Signal name
Signal path
Ignition signal
—
Fuel filler cap warning display signal
ECM
Combination meter
Signal name
Signal Path
Ignition signal
—
Low tire pressure warning lamp signal
BCM
Combination
meter
MWI-20
< SYSTEM DESCRIPTION >
OPERATION
OPERATION
Switch Name and Function
INFOID:0000000012201312
JSNIA3203ZZ
Switch name
Operation
Description
Illumination control switch (1)
Press
An illuminance level of the back light of the combination meter can be adjusted.
Meter control switch (2)
• The information display screen can be switched.
• An indicated value of the trip computer can be reset by pressing and holding the
meter control switch.
MWI
DIAGNOSIS SYSTEM (COMBINATION METER)
MWI-21
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DIAGNOSIS SYSTEM (COMBINATION METER)
On Board Diagnosis Function
INFOID:0000000012201313
ON BOARD DIAGNOSIS ITEM
The combination meter allows the following diagnosis items with the on-board diagnosis function.
METHOD OF STARTING
1. Turn ignition switch ON, and switch the trip meter to “trip A” or “trip B”.
2. Turn ignition switch OFF.
3. While pressing the meter control switch (1), turn ignition switch
ON.
4. Make sure that the trip meter displays “0000.0”.
5. Press the meter control switch at least 3 times. (Within 7 sec-
onds after the ignition switch is turned ON.)
6. The combination meter is turned to self-diagnosis mode.
All of the segments of fuel gauge, odo/trip meter, shift position
indicator (A) for CVT models and information display illuminate.
NOTE:
• Check combination meter power supply and ground circuit
when the self-diagnosis mode of the combination meter does
not start. Replace combination meter if power supply and
ground circuit are normal.
• If any of the dots are not displayed, replace combination
meter.
• For M/T models, start-up lamp (B) illuminate instead of shift
position indicator.
7. Each meter activates by pressing the meter control switch.
NOTE:
Diagnosis item
Drive circuit check
• Speedometer
• Tachometer
LCD (liquid crystal dis-
play) check
Information display
JSNIA3204ZZ
JSNIA8952ZZ
JSNIA8953ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст