Volvo V70 (2016 year). Manual — part 6
||
03 Instruments and controls
03
102
Upper row: left-hand drive cars, templates A and B. Lower row: right-hand drive cars, templates C and D.
03 Instruments and controls
03
103
Templates for halogen headlamps
03 Instruments and controls
03
104
*
Option/accessory, for more information, see Introduction.
Wipers and washers
Wipers and washers clean the windscreen
and rear window. The headlamps are cleaned
with high-pressure washing.
Windscreen wipers
22
Windscreen wipers and windscreen washers.
Rain sensor, On/Off
Thumbwheel sensitivity/frequency
Windscreen wipers off
Move the stalk switch to position 0
to switch off the windscreen wipers.
Single sweep
Raise the stalk switch and release to
make one sweep.
Intermittent wiping
Set the number of sweeps per time
unit with the thumbwheel when
intermittent wiping is selected.
Continuous wiping
The wipers sweep at normal speed.
The wipers sweep at high speed.
Before activating the wipers during winter
ensure that the wiper blades are not frozen
in, and that any snow or ice on the wind-
screen is scraped away.
Use plenty of washer fluid when the wipers
are cleaning the windscreen. The wind-
screen must be wet when the windscreen
wipers are operating.
Service position wiper blade
For cleaning the windscreen/wiper blades
and replacement of wiper blades, see Car
wash (p. 398) and Wiper blades (p. 375).
Rain sensor*
The rain sensor automatically starts the wind-
screen wipers based on how much water it
detects on the windscreen. The sensitivity of
the rain sensor can be adjusted using the
thumbwheel.
When the rain sensor is activated a lamp in
the button is illuminated and the rain sensor
symbol
is shown in the combined
instrument panel.
Activating and setting the sensitivity
When activating the rain sensor, the car must
be running or the remote control key in posi-
tion I or II while the windscreen wiper stalk
switch must be in position 0 or in the position
for a single sweep.
Activate the rain sensor by pressing the rain
sensor button
. The windscreen wipers
make one sweep.
Press the stalk switch up for the wipers to
make an extra sweep.
Turn the thumbwheel upward for higher sen-
sitivity and downward for lower sensitivity.
(An extra sweep is made when the thumb-
wheel is turned upward.)
Deactivate
Deactivate the rain sensor by pressing the
rain sensor button
or move the stalk
switch down to another wiper program.
22
For replacing the wiper blades and service position wiper blades, see Wiper blades (p. 375). For filling washer fluid, see Washer fluid - filling (p. 377).
03 Instruments and controls
03
}}
*
Option/accessory, for more information, see Introduction.
105
The rain sensor is automatically deactivated
when the remote control key is removed from
the ignition switch or five minutes after the
engine has been switched off.
The windscreen wipers could start and be
damaged in an automatic car wash.
Switch off the rain sensor while the car is
in motion or when the remote control key
is in position I or II. The symbol in the
combined instrument panel and the lamp
in the button go out.
Washing the headlamps and windows
Washing function.
Washing the windscreen
Move the stalk switch toward the steering
wheel to start the windscreen and headlamp
washers.
The windscreen wipers will make several
more sweeps and the headlamps are washed
once the stalk switch has been released.
Heated washer nozzles*
The washer nozzles are heated automatically
in cold weather to prevent the washer fluid
freezing solid.
High-pressure headlamp washing*
High-pressure headlamp washing consumes
a large quantity of washer fluid. To save fluid,
the headlamps are washed automatically at
every fifth windscreen wash cycle.
Reduced washing
If only approx. 1 litre of washer fluid remains
in the reservoir and the message that you
should fill the washer fluid is shown in the
combined instrument panel, then the supply
of washer fluid to the headlamps is switched
off. This is in order to prioritise cleaning the
windscreen and the visibility through it.
Wiping and washing the rear window
Rear window wiper – intermittent wiping
Rear window wiper – continuous speed
Press the stalk switch forward (see the arrow
in the illustration above) to initiate rear win-
dow washing and wiping.
The rear window wiper is equipped with
overheating protection which means that
the motor is switched off if it overheats.
The rear window wiper works again after a
cooling period (30 seconds or longer,
depending on the heat in the motor and
the outside temperature).
||
03 Instruments and controls
03
106
*
Option/accessory, for more information, see Introduction.
Wiper – reversing
Engaging reverse gear while the windscreen
wipers are on initiates intermittent rear win-
dow wiping
23
. The function stops when
reverse gear is disengaged.
If the rear window wiper is already on at con-
tinuous speed, no change is made.
On cars with rain sensors, the rear wiper is
activated during reversing if the sensor is
activated and it is raining.
Related information
•
Washer fluid - filling (p. 377)
Power windows
All power windows can be operated using the
control panel for the driver's door - the con-
trol panels for the other doors operate their
respective power window.
Driver's door control panel.
Switch for electric child safety locks* and
disengaging rear power window buttons;
see Child safety locks - electrical activa-
tion* (p. 189).
Rear window controls
Front window controls
WARNING
Check that children or other passengers
are not trapped when the windows are
closed from the driver's door.
WARNING
Check that no children or other passen-
gers are trapped if/when the windows are
closed using the remote control key.
WARNING
If there are children in the car - remember
to always switch off the power supply to
the power windows by selecting key posi-
tion 0 and then take the remote control key
with you when leaving the car. For infor-
mation on key positions - see Key posi-
tions - functions at different levels (p. 81).
23
This function (intermittent wiping when reversing) can be deactivated. Visit a workshop. Volvo recommends an authorised Volvo workshop.
03 Instruments and controls
03
107
Operating
Operating the power windows.
Operating without auto
Operating with auto
All power windows can be operated using the
control panel for the driver's door - the con-
trol panels for the other doors can only each
operate their respective power window. Only
one control panel can be operated at a time.
In order for the power windows to be used,
the key position must be at least I - see Key
positions - functions at different levels (p. 81).
The power windows can be operated for a
few minutes after the engine has been
switched off and after the remote control key
has been removed - although not after a door
has been opened.
Closing of the windows is stopped and the
window is opened if anything prevents its
movement. It is possible to force the pinch
protection when closing has been interrupted,
e.g. with ice, by continuously holding the but-
ton up until the window is closed. The pinch
protection is reactivated after a brief pause.
One way to reduce the pulsating wind
noise when the rear windows are open is
to also open the front windows slightly.
Operating without auto
Move one of the controls up/down gently.
The power windows move up/down as long
as the control is held in position.
Operating with auto
Move one of the controls up/down to the end
position and release it. The window runs
automatically to its end position.
Operating with the remote control key
and central locking
To remotely operate the power windows from
the outside with the remote control key or
from inside with central locking, see Remote
control key (p. 167) and Locking/unlocking -
Resetting
If the battery is disconnected then the func-
tion for automatic opening must be reset so
that it can work correctly.
1. Gently raise the front section of the but-
ton to raise the window to its end position
and hold it there for one second.
2. Release the button briefly.
3. Raise the front section of the button again
for one second.
WARNING
A reset must take place for pinch protec-
tion to work.
03 Instruments and controls
03
108
*
Option/accessory, for more information, see Introduction.
Door mirrors
The door mirror positions are adjusted with
the joystick in the driver's door controls.
Door mirror controls.
Adjusting
1. Press the L button for the left-hand door
mirror or the R button for the right-hand
door mirror. The light in the button illumi-
nates.
2. Adjust the position with the joystick in the
centre.
3. Press the L or R button again. The light
should no longer be illuminated.
WARNING
Both mirrors are the wide-angle type to
provide optimal vision. Objects may
appear further away than they actually are.
Storing settings
24
The settings for the rearview and door mirrors
and the positions of the driver's seat can be
stored for each remote control key in the car
key memory*, see Remote control key - per-
Angling the door mirror when parking
24
The door mirror can be angled down for the
driver to view the side of the road when park-
ing for example.
–
Engage reverse gear and press the L or R
button.
When reverse gear is disengaged the mirror
automatically returns to its original position
after approx. 10 seconds, or earlier by press-
ing the button labelled L or R respectively.
Automatic angling of the door mirror
when parking
24
When reverse gear is engaged the door mirror
is automatically angled down so that the
driver can see the side of the road when
parking for example. When reverse gear is
disengaged the mirror automatically returns
to its original position after a short time.
The function can be activated/deactivated in
the menu system MY CAR, see MY CAR
Automatic retraction when locking
24
When the car is locked/unlocked with the
remote control key the door mirrors are auto-
matically retracted/extended.
The function can be activated/deactivated in
the menu system MY CAR, see MY CAR
Resetting to neutral
Mirrors that have been moved out of position
by an external force must be reset electrically
to the neutral position for electric retracting/
extending to work correctly:
1. Retract the mirrors with the L and R but-
tons.
2. Fold them out again with the L and R but-
tons.
3. Repeat the above procedure as neces-
sary.
The mirrors are now reset in neutral position.
Retractable power door mirrors*
The mirrors can be retracted for parking/driv-
ing in narrow spaces:
1. Depress the L and R buttons simultane-
ously (key position must be at least I).
24
Only in combination with power seat with memory, see Seats, front - electrically operated* (p. 83).
03 Instruments and controls
03
*
Option/accessory, for more information, see Introduction.
109
2. Release them after approximately
1 second. The mirrors automatically stop
in the fully retracted position.
Fold out the mirrors by pressing down the L
and R buttons simultaneously. The mirrors
automatically stop in the fully extended posi-
tion.
Home safe and approach lighting
The lamp on the door mirrors illuminates
when approach lighting (p. 99) or home safe
Related information
•
Rearview mirror - interior (p. 110)
•
Windows and rearview and door mirrors -
Windows and rearview and door
mirrors - heating
The defroster is used to quickly remove mist-
ing and ice from the windscreen, rear window
and door mirrors.
Heated windscreen*, rear window and
door mirrors
Heating, windscreen
Heating, rear window and door mirrors
The function is used to remove ice and mist-
ing from the windscreen, rear window and
door mirrors.
One press of the respective button starts the
heating. The light in the button indicates that
the function is active. Switch off the heating
as soon as the ice/misting is cleared in order
not to load the battery unnecessarily. How-
ever, the function is switched off automati-
cally after a certain time.
See also Demisting and defrosting the wind-
screen (p. 140).
The door mirrors and rear window are demis-
ted/defrosted automatically if the car is
started in an outside temperature lower than
+7 °C. Automatic defrosting can be selected
03 Instruments and controls
03
110
*
Option/accessory, for more information, see Introduction.
Rearview mirror - interior
The interior rearview mirror can be dimmed
with a control in the mirror's lower edge.
Alternatively, the rearview mirror dims auto-
matically.
Control for dimming
Manual dimming
Bright light from behind could be reflected in
the rearview mirror and dazzle the driver. Use
dimming with the dimming control when
lights from behind are distracting:
1. Use dimming by moving the control in
towards the passenger compartment.
2. Return to normal position by moving the
control towards the windscreen.
Automatic dimming*
Bright light from behind is automatically
dimmed by the rearview mirror. The control
for manual dimming is not available on mir-
rors with automatic dimming.
The rearview mirror contains two sensors -
one forward facing and one rearward facing -
that work together to identify and eliminate
dazzling light. The forward facing sensor
detects ambient light, while the rearward fac-
ing sensor detects the light from vehicle
headlights behind.
If the sensors are obscured by e.g. parking
permits, transponders, sun visors or
objects in the seats or in the cargo area in
such a way that light is prevented from
reaching the sensors, then the dimming
function of the rearview mirror is reduced.
Only rearview mirror with automatic dimming
can be equipped with compass (p. 110).
Related information
•
Compass*
The upper right-hand corner of the rearview
mirror contains a display that shows the com-
pass direction in which the front of the car is
pointing.
Operation
Rearview mirror with compass.
Eight different directions are shown with Eng-
lish abbreviations:
N
(north),
NE
(north east),
E
(east),
SE
(south east),
S
(south),
SW
(south
west),
W
(west) and
NW
(north west).
The compass is activated automatically when
the car is started or when key position II is
active, see Key positions - functions at differ-
ent levels (p. 81). To deactivate/activate the
compass - press in the button on the under-
side of the mirror using a paper clip for exam-
ple.
03 Instruments and controls
03
*
Option/accessory, for more information, see Introduction.
111
Calibration
The compass may need calibrating to show
the correct compass direction.
The earth is divided into 15 magnetic zones.
The compass should be calibrated if the car
is moved across several magnetic zones.
Proceed as follows to perform calibration:
1. Stop the car in a large open area free
from steel structures and high-voltage
power lines.
2. Start the car and switch off all electrical
equipment (air conditioning, wipers, etc.)
and ensure that all doors are closed.
Calibration may fail or not start at all if
electrical equipment is not switched off.
3. Hold the button on the underside of the
rearview mirror depressed (use a paper
clip or similar) for approx. 3 seconds. The
number of the current magnetic zone is
shown.
Magnetic zones.
4. Press the button repeatedly until the
required magnetic zone (
1–15
) is shown.
See the map of magnetic zones for the
compass.
5. Wait until the display returns to showing
the character
C
, or hold the button on the
underside of the rearview mirror
depressed for approx. 6 seconds until the
character
C
is shown.
6. Drive slowly in a circle at a speed of no
more than 10 km/h until a compass direc-
tion is shown in the display, indicating
that calibration is complete. Then drive a
further 2 circles to fine-tune calibration.
7. Cars with heated windscreen*: If the
character
C
is shown in the display when
the heated windscreen is activated, per-
form the calibration in accordance with
point 6 above with the heated windscreen
activated, see Demisting and defrosting
8. Repeat the above procedure as neces-
sary.
03 Instruments and controls
03
112
*
Option/accessory, for more information, see Introduction.
Sunroof*
The sunroof can be operated with a control in
the roof panel.
The sunroof's inner sunscreen is closed man-
ually.
The sunroof has a wind deflector.
The sunroof controls are located in the roof
panel. The sunroof can be opened vertically
at the rear edge and horizontally. Key position
I or II is required for the sunroof to be
opened.
Horizontal opening
G017823
Horizontal opening, backward/forward.
Opening, automatic
Opening, manual
Closing, manual
Closing, automatic
Opening
For maximum sunroof opening, move the
control back to the position for automatic
opening and release.
Open manually by pulling the control back-
wards to the point of resistance for manual
opening. The sunroof moves to maximum
open position as long as the button is kept
depressed.
Closing
Close manually by pushing the control for-
wards to the point of resistance for manual
closing. The sunroof moves to closed posi-
tion as long as the button is kept depressed.
WARNING
Risk of crushing when the sunroof is
closed. The sunroof's pinch-protection
function only operates during automatic
closing, not manual.
Close automatically by pressing the control to
the position for automatic closing and then
release it.
The power supply to the sunroof is switched
off by selecting key position 0 and removing
the remote control key from the ignition
switch.
WARNING
If there are children in the car:
Remember to always switch off the power
supply to the sunroof by selecting key
position 0 and then take the remote con-
trol key with you when leaving the car. For
information on key positions - see Key
positions - functions at different levels
Vertical opening
G028900
Vertical opening, raised at the rear edge.
Open by pressing the rear edge of the
control upward.
Close by pulling the rear edge of the con-
trol down.
03 Instruments and controls
03
}}
113
Closing using the remote control key or
central locking button
G021345
One long press on the lock button closes the
sunroof and all the windows, see Remote
control key - functions (p. 170) and Locking/
unlocking - from the inside (p. 183). The
doors and the tailgate are locked. To interrupt
closing, press the lock button again.
WARNING
If the sunroof is closed with the remote
control key, check that no one risks being
trapped.
Sunscreen
The sunroof features a manual, sliding interior
sunscreen. The sunscreen slides back auto-
matically when the sunroof is opened. Grip
the handle and slide the screen forward to
close it.
Pinch protection
The sunroof's pinch protection function is
triggered if it is blocked by an object during
automatic closing. If blocked, the sunroof will
stop and automatically open to the previous
position.
Wind deflector
The sunroof has a wind deflector that is
folded up when the sunroof is in the open
position.
Menu navigation - combined
instrument panel
The left-hand stalk controls the menus
(p. 114) shown on the information display in
the combined instrument panel (p. 65). Which
menus are shown depends on the key posi-
Display (analogue combined instrument panel)
and controls for menu navigation.
||
03 Instruments and controls
03
114
*
Option/accessory, for more information, see Introduction.
Display (digital combined instrument panel) and
controls for menu navigation.
OK – access to message list and mes-
sage confirmation.
Thumbwheel – browse between menu
options.
RESET – reset the active function. Used
in certain cases to select/activate a func-
tion, see the explanation under each
respective function.
If there is a message (p. 115) then it must be
acknowledged with OK in order that the
menus shall be shown.
Related information
•
Menu overview - combined
instrument panel
Which menus are shown in the combined
instrument panel's information display
depends on the key position (p. 81).
Some of the following menu options require
the function and hardware to be installed in
the car.
Analogue combined instrument panel
Digital speed
Parking heater*
Additional heater*
TC options
Service status
Oil level
25
Messages (##)
26
Digital combined instrument panel
Settings*
Themes
Contrast mode/Colour mode
Service status
Messages
26
Oil level
25
Parking heater*
Trip computer reset
Related information
•
Analogue combined instrument panel -
•
Digital combined instrument panel - over-
•
Menu navigation - combined instrument
25
Certain engines.
26
The number of messages is indicated in brackets.
03 Instruments and controls
03
*
Option/accessory, for more information, see Introduction.
115
Messages
When a warning, information or indicator
symbol illuminates, a corresponding message
appears on the information display.
Message
Specification
Stop safely
A
Stop and switch off the
engine. Serious risk of
damage - consult a work-
shop
B
.
Stop engine
A
Stop and switch off the
engine. Serious risk of
damage - consult a work-
shop
B
.
Service
urgent
A
Contact a workshop
B
to
check the car immedi-
ately.
Service
required
A
Contact a workshop
B
to
check the car as soon as
possible.
See manual
A
Read the owner's man-
ual.
Book time
for mainte-
nance
Time to book regular
service - contact a work-
shop
B
.
Message
Specification
Time for reg-
ular mainte-
nance
Time for regular service -
contact a workshop
B
. The
timing is determined by
the number of kilometres
driven, number of months
since the last service,
engine running time and
oil grade.
Maintenance
overdue
If the service intervals are
not followed then the
warranty does not cover
any damaged parts -
contact a workshop
B
.
Transmission
Oil change
needed
Contact a workshop
B
to
check the car as soon as
possible.
Transmission
Reduced
performance
The gearbox cannot han-
dle full capacity. Drive
carefully until the mes-
sage clears
C
.
If shown repeatedly -
contact a workshop
B
.
Transmission
hot Reduce
speed
Drive more smoothly or
stop the car in a safe
manner. Disengage the
gear and run the engine
at idling speed until the
message clears
C
.
Message
Specification
Transmission
hot Stop
safely Wait
for cooling
Critical fault. Stop the car
immediately in a safe
manner and contact a
workshop
B
.
Temporarily
off
A
A function has been tem-
porarily switched off and
is reset automatically
while driving or after star-
ting again.
Low battery
charge
Power save
mode
The audio system is
switched off to save
energy. Charge the bat-
tery.
A
Part of message, shown together with information on
where the problem has arisen.
B
An authorised Volvo workshop is recommended.
C
For more information regarding the automatic gearbox, see
Automatic gearbox -- Geartronic* (p. 273).
Related information
•
•
03 Instruments and controls
03
116
*
Option/accessory, for more information, see Introduction.
Messages - handling
Use the left-hand stalk switch to acknowledge
and browse among messages (p. 115) that
are shown in the information display of the
combined instrument panel.
When a warning, information or indicator
symbol illuminates, a corresponding message
appears in the display at the same time. An
error message is stored in a memory list until
the fault has been rectified.
Press OK on the left-hand stalk switch to
acknowledge a message. Scroll through mes-
sages with the thumbwheel (p. 113).
If a warning message appears while you
are using the trip computer, the message
must be read (press OK) before the previ-
ous activity can be resumed.
Related information
•
Menu overview - combined instrument
MY CAR
MY CAR is a menu source that handles many
of the car's functions, e.g. City Safety™, locks
and alarm, automatic fan speed, setting the
clock, etc.
Certain functions are standard, others are
optional - the range also varies depending on
the market.
Operation
Navigation in the menus is carried out using
buttons in the centre console or with the
steering wheel's right-hand keypad*.
Control panel in centre console and steering
wheel keypad. The figure is schematic - the num-
ber of functions and layout of the buttons both
03 Instruments and controls
03
}}
117
vary, depending on the equipment selected and
the market.
MY CAR - opens the menu system MY
CAR.
OK/MENU - press the button in the cen-
tre console or the thumbwheel on the
steering wheel to select/tick in the high-
lighted menu option or store the selected
function in the memory.
TUNE - turn the knob in the centre con-
sole or the thumbwheel on the steering
wheel to scroll up/down through the
menu options.
EXIT
EXIT functions
Depending on the function the cursor is on
when EXIT is depressed briefly, and on which
menu level, one of the following may occur:
•
phone call is rejected
•
current function is interrupted
•
input characters are deleted
•
most recent selections are undone
•
leads up in the menu system.
A long press on EXIT leads to the normal
view for MY CAR or if you are in the normal
view, to the highest menu level (main source
menu).
Menu options and search paths
For a description of the menu options and
search paths in MY CAR, see the Sensus
Infotainment supplement.
Trip computer
The car's trip computer can record, calculate
and show information while driving.
Trip computer content and appearance varies
depending on whether the combined instru-
ment panel is analogue or digital:
•
Trip computer - analogue combined
•
Trip computer - digital combined instru-
Checking and settings of the trip computer
can be made immediately after the combined
instrument panel is automatically illuminated
in connection with unlocking. If none of the
trip computer's controls are actuated within
approx. 30 seconds after the driver's door
has been opened then the instrument extin-
guishes, after which either key position II
(p. 81) or starting the engine is required in
order to operate the trip computer.
If a warning message appears when the
trip computer is used then the message
must first be acknowledged before the trip
computer can be reactivated.
•
Acknowledge the message by briefly
pressing the indicator stalk OK button.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст