Honda Clarity Plug-in Hybrid (2018 year). Manual — part 7
96
uu
Indicators
u
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
Low Tire
Pressure/TPMS
Indicator
●
Comes on for a few seconds when
you set the power mode to ON.
●
May come on briefly if the power
mode is set to ON and the vehicle
is not moved within 45 seconds, to
indicate the calibration process is
not yet complete.
●
Comes on and stays on when:
- One or more tires’ pressures are
determined to be significantly
low.
- The system has not been
calibrated.
●
Comes on while driving - Stop in a safe
place, check tire pressures, and inflate the
tire(s) if necessary.
●
Stays on after the tires are inflated to
the recommended pressures - The
system needs to be calibrated.
2 TPMS Calibration P. 425
●
Blinks for about one minute, and
then stays on if there is a problem
with the TPMS.
●
Blinks and remains on - Have your
vehicle checked by an authorized Honda
Clarity Plug-In Hybrid dealer.
●
Comes on if the TPMS is
deactivated temporarily after the
battery has been disconnected,
then re-connected.
●
Drive a short distance at more than 12
mph (20 km/h). The indicator should go
off. If it does not, have your vehicle
checked by an authorized Honda Clarity
Plug-In Hybrid dealer.
97
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
*1:Canadian models only: Apply and hold the brake pedal before selecting the ON mode.
Indicator
Name
On/Blinking
Explanation
Message
Turn Signal and
Hazard Warning
Indicators
●
Blinks when you operate the turn
signal lever.
●
Blinks along with all turn signals
when you press the hazard
warning button.
●
Does not blink or blinks rapidly -
Have your vehicle checked by an
authorized Honda Clarity Plug-In Hybrid
dealer immediately.
—
High Beam
Indicator
●
Comes on when the high beam
headlights are on.
—
—
Lights On
Indicator
●
Comes on when the light switch in
a position other than OFF or when
the switch is set to AUTO and the
exterior lights come on.
●
If you set the power mode to
ACCESSORY or VEHICLE OFF while the
exterior lights are on, a chime sounds
when the driver’s door is opened.
—
Immobilizer
System Indicator
●
Blinks if the immobilizer system
cannot recognize the key
information.
●
Blinks - You cannot start the power
system. Set the power mode to VEHICLE
OFF
*1
, then select the ON mode again.
●
Repeatedly blinks - The system may be
malfunctioning. Have your vehicle
checked by an authorized Honda Clarity
Plug-In Hybrid dealer.
●
Do not attempt to alter this system or add
other devices to it. Electrical problems can
occur.
Indicator
Canadian models
98
uu
Indicators
u
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
System Message
Indicator
●
Comes on along with a beep when
a problem is detected. A system
message on the driver information
interface appears at the same time.
●
While the indicator is on, press the
(display/information) button to see the
message again.
●
Refer to the Indicators information in this
chapter when a system message appears
on the driver information interface. Take
the appropriate action for the message.
●
The driver information interface does not
return to the normal screen unless the
warning is canceled, or the
button is
pressed.
—
Security System
Alarm Indicator
●
Blinks when the security system
alarm has been set.
2 Security System Alarm P. 153
—
SPORT Mode
Indicator
●
Comes on when you press the
SPORT button.
●
The ambient meter remains lit up
in red as long as sport mode is on.
2 SPORT Mode P. 389
ECON Mode
Indicator
●
Comes on when ECON mode is on.
Indicator
99
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
Road Departure
Mitigation
(RDM) Indicator
●
Comes on for a few seconds when
you set the power mode to ON,
then goes off.
●
Comes on if there is a problem
with the RDM system.
●
Stays on constantly - Have your vehicle
checked by an authorized Honda Clarity
Plug-In Hybrid dealer.
●
Comes on when the RDM system
shuts itself off.
●
Stays on - The temperature inside the
camera is too high.
Use the climate control system to cool
down the camera.
The system activates when the
temperature inside the camera cools
down sufficiently.
●
Stays on - The area around the camera is
blocked by dirt, mud, etc. Stop your
vehicle in a safe place, and wipe it off
with a soft cloth.
●
Have your vehicle checked by an
authorized Honda Clarity Plug-In Hybrid
dealer if the indicator and message come
back on after you cleaned the area
around the camera.
100
uu
Indicators
u
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
Adaptive Cruise
Control (ACC)
with Low Speed
Follow (LSF)
Indicator
(Amber)
●
Comes on for a few seconds when
you set the power mode to ON,
then goes off.
●
Comes on if there is a problem
with ACC with LSF.
●
Comes on while driving - Have your
vehicle checked by an authorized Honda
Clarity Plug-In Hybrid dealer.
●
Comes on if anything covers the
radar sensor cover and prevents
the sensor from detecting a vehicle
in front.
●
May come on when driving in bad
weather (rain, snow, fog, etc.)
●
ACC with LSF has been
automatically canceled.
●
When the radar sensor gets dirty, stop
your vehicle in a safe place, and then
clean the sensor using a soft cloth.
●
Have your vehicle checked by an
authorized Honda Clarity Plug-In Hybrid
dealer if the indicator does not disappear,
even after you clean the sensor cover.
Adaptive Cruise
Control (ACC)
with Low Speed
Follow (LSF)
Indicator (Green)
●
Comes on when you press the
MAIN button.
2 Adaptive Cruise Control (ACC) with
—
101
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
Lane Keeping
Assist System
(LKAS) Indicator
(Amber)
●
Comes on for a few seconds when
you set the power mode to ON,
then goes off.
●
Comes on if there is a problem
with the LKAS.
●
Stays on constantly - Have your vehicle
checked by an authorized Honda Clarity
Plug-In Hybrid dealer.
Lane Keeping
Assist System
(LKAS) Indicator
(Green)
●
Comes on when you press the
MAIN button.
2 Lane Keeping Assist System (LKAS)
P. 415
—
Collision
Mitigation
Braking
System
TM
(CMBS
TM
)
Indicator
●
Comes on for a few seconds when
you set the power mode to ON,
then goes off.
●
Comes on when you deactivate
the CMBS
TM
.
●
Comes on if there is a problem
with the CMBS
TM
.
●
Stays on constantly without the
CMBS
TM
off - Have your vehicle checked
by an authorized Honda Clarity Plug-In
Hybrid dealer.
2 Collision Mitigation Braking
●
Comes on if the CMBS is
deactivated temporarily after the
battery has been disconnected,
then re-connected.
●
Drive a short distance at more than 12
mph (20 km/h). The indicator should go
off. If it does not, have your vehicle
checked by an authorized Honda Clarity
Plug-In Hybrid dealer.
102
uu
Indicators
u
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
Collision
Mitigation
Braking
System
TM
(CMBS
TM
)
Indicator
●
Comes on when the CMBS
TM
system shuts itself off.
●
Stays on - The area around the camera is
blocked by dirt, mud, etc. Stop your
vehicle in a safe place, and wipe it off
with a soft cloth.
●
When the radar sensor gets dirty, stop
your vehicle in a safe place, and then
clean the sensor using a soft cloth.
●
Have your vehicle checked by an
authorized Honda Clarity Plug-In Hybrid
dealer if the message does not disappear
even after you clean the sensor cover.
2 Collision Mitigation Braking
●
Stays on - The temperature inside the
camera is too high. Use the climate
control system to cool down the camera.
The system activates when the
temperature inside the camera cools
down sufficiently.
103
uu
Indicators
u
Driver Information Interface Warning and Information Messages
Continued
In
strum
e
nt Pa
nel
Driver Information Interface Warning and Information Messages
The following messages appear only on the driver information interface. Press the
(display/information) button to see the message
again with the system message indicator on.
Message
Condition
Explanation
●
Appears when the vehicle cannot be driven.
●
Immediately stop in a safe place.
●
Appears when the washer fluid gets low.
●
Refill the washer fluid.
2 Refilling Window Washer Fluid P. 493
●
Appears when the scheduled maintenance is due
soon.
●
Consequently, Service Due Now and Service Past
Due follow.
2 Warning Message and Maintenance Minder
Information on the Driver Information Interface
P. 476
●
Appears as soon as a problem is detected in the
smart entry system or push button starting system.
●
Appears constantly - Have your vehicle checked by an
authorized Honda Clarity Plug-In Hybrid dealer.
Canadian models
104
uu
Indicators
u
Driver Information Interface Warning and Information Messages
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears when there is a problem with the sensor on
the 12-volt battery.
●
Have your vehicle checked by an authorized Honda
Clarity Plug-In Hybrid dealer.
2 Checking the 12-Volt Battery P. 508
●
Appears along with the battery charging system
indicator when the battery is not charging.
●
Turn off the climate control system and rear defogger to
reduce electricity consumption.
2 If the 12-Volt Battery Charging System Indicator
●
Appears when the engine oil pressure is low.
●
Appears while driving - Immediately stop in a safe
place.
2 If the Low Oil Pressure Warning Appears P. 545
●
Appears when the engine coolant temperature gets
abnormally high.
2 Overheating P. 542
●
Appears when the engine coolant temperature is
near its upper limit.
●
Drive slowly to prevent overheating.
●
Appears if there is a problem with the cooling
system.
●
Drive slowly to prevent overheating and have your
vehicle checked by an authorized Honda Clarity Plug-In
Hybrid dealer as soon as possible.
●
Appears when the fuel fill cap is loose or is not
installed.
105
uu
Indicators
u
Driver Information Interface Warning and Information Messages
Continued
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears if the vehicle’s speed reaches about 10 mph
(15 km/h) with the fuel fill door opened.
●
Stop the vehicle and close the fuel fill door.
●
Appears when the fuel fill door has been open for 30
minutes.
●
Turn off the power system, reinstall the fuel cap, and
close the fuel fill door.
- If you still want to refuel, press the fuel fill door release
button to reopen the door.
106
uu
Indicators
u
Driver Information Interface Warning and Information Messages
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears after the driver’s door is opened when the
power mode is in ACCESSORY.
●
Press the POWER button twice with your foot off the
brake pedal to change the power mode to VEHICLE
OFF.
●
Appears when the power mode is in ACCESSORY.
—
●
Appears when you close the door with the power
mode in ON without the smart entry remote inside
the vehicle.
●
Disappears when you bring the smart entry remote back
inside the vehicle and close the door.
2 Smart Entry Remote Reminder P. 160
●
Appears when the smart entry remote battery
becomes weak.
●
Replace the battery as soon as possible.
2 Replacing the Button Battery P. 510
●
Appears if the smart entry remote’s battery is too
weak to turn on the power system or the key is not
within operating range to turn on the power system.
A beeper sounds six times.
●
Bring the back of the smart entry remote into contact
with the POWER button.
2 If the Smart Entry Remote Battery is Weak P. 537
●
Appears when you set the power mode to
ACCESSORY or ON.
●
Appears after you unlock and open the driver’s door.
2 Turning on the Power P. 376
●
Appears when the POWER button is pressed while
driving.
2 Emergency Power System Off P. 538
Canadian models
107
uu
Indicators
u
Driver Information Interface Warning and Information Messages
Continued
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears when the high voltage battery charge level
is extremely low.
●
Caused by the low battery charge level -
Immediately charge the high voltage battery.
●
Appears when the power system temperature is low.
●
Your vehicle has less ability to accelerate and may be
harder to start on an incline.
●
In extremely cold climates, keep the vehicle stored in a
garage.
●
In extremely cold climates, keep the vehicle stored in a
garage and connect the charging connector.
●
Appears when the power system temperature is
high.
●
Your vehicle has less ability to accelerate and may be
harder to start on an incline.
●
Park in a safe place, and cool the system down.
2 Overheating P. 542
●
Appears if the power system is in diagnostic mode.
●
You may notice a decrease in available power. Have
your vehicle checked by an authorized Honda Clarity
Plug-In Hybrid dealer immediately.
●
As a result of diagnostics, the POWER SYSTEM
indicator may come on.
2 POWER SYSTEM Indicator P. 88
U.S. models
Canadian models
108
uu
Indicators
u
Driver Information Interface Warning and Information Messages
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears when the charging connector is connected
to the inlet.
●
The vehicle does not move while the charging
connector is plugged into the inlet.
●
Appears when there is a problem with the standard
plug-in charging system or the charging station
outlet.
●
This message only - There may be a problem with the
charging station outlet. Refer to the instructions
provided at the station or consult a qualified technician.
If the outlet works properly, have the vehicle checked by
an authorized Honda Clarity Plug-In Hybrid dealer.
●
Comes on with the POWER SYSTEM indicator -
Have your vehicle checked by an authorized Honda
Clarity Plug-In Hybrid dealer.
●
Appears if there is a problem with the acoustic
vehicle alerting system.
●
Have your vehicle checked by an authorized Honda
Clarity Plug-In Hybrid dealer immediately.
●
Appears when the charge lid is open.
●
Close the charge lid.
109
uu
Indicators
u
Driver Information Interface Warning and Information Messages
Continued
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears when you press the fuel fill door release
button.
●
The display changes to Ready when the fuel vapor
pressure inside the fuel tank is released. You can start
refueling once Ready appears.
●
Appears when the vehicle is ready to be refueled.
●
Appears when the high voltage battery and other
system control temperatures are too low to operate
(approx. –22°F [–30°C] or below).
●
You must wait for an increase in the ambient
temperature or move the vehicle to a warmer location.
●
Consult an authorized Honda Clarity Plug-In Hybrid
dealer.
●
In extremely cold climates, keep the vehicle stored in a
garage.
●
In extremely cold climates, keep the vehicle stored in a
garage and connect the charging connector.
●
Appears when the charging connector is
disconnected while the power mode is in ON with
the charging connector connected.
●
Set the power mode to OFF, then set it back to ON if
you drive again.
●
Appears when the high voltage battery temperature
is too low to operate (approx. −22°F [−30°C]).
●
You can start the engine and use the climate control
system to warm up the interior.
●
You must wait for an increase in the high voltage
battery temperature to drive.
U.S. models
Canadian models
Canadian models
110
uu
Indicators
u
Driver Information Interface Warning and Information Messages
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears when the outside temperature is low.
●
In extremely cold climates, keep the vehicle stored in a
garage or connect the charging connector.
●
Appears when the engine starts automatically when
the engine has not started for a long time.
—
●
Appears when the vehicle can run only in EV because
the failure that cannot generate power by the engine
failure or generator failure etc occurs.
●
The estimated distance you can travel on the
remaining power is displayed.
●
Have your vehicle checked by an authorized Honda
Clarity Plug-In Hybrid dealer.
●
Appears when you are unable to select the HV
Charge because the High Voltage battery charge
level is at maximum limit (12 segments) of the HV
Charge.
2 SPORT HYBRID i-MMD Plug-in (Intelligent Multi-
●
Appears if the drive mode cannot be changed due to
certain situations, such as a system error or adverse
driving conditions.
—
Canadian models
111
uu
Indicators
u
Driver Information Interface Warning and Information Messages
Continued
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears when you set the power mode to ON
without fastening the driver’s seat belt.
●
Appears if the gear position has been automatically
changed to
(
P and the driver attempts to take the
vehicle out of
(
P but does not have his or her
seatbelt fastened.
●
Fasten the seat belt properly before you start to drive.
●
Appears when you try to change the gear position
without depressing the brake pedal while the
transmission is in
(
P or
(
N.
●
Depress the brake pedal, then select a shift button.
●
Appears when you try to change the gear position
without releasing your foot off the accelerator pedal
while the transmission is in
(
P or
(
N.
●
Release your foot off the accelerator pedal, then select
a shift button.
●
Appears when the transmission system temperature
is too high.
●
Park in a safe place, and allow the system to cool down
sufficiently.
●
Appears when you depress the accelerator pedal
while the transmission is in
(
N.
●
Release the accelerator pedal.
●
Depress the brake pedal, then select a shift button to
start driving.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст