Honda Clarity Plug-in Hybrid (2018 year). Manual — part 34
529
uu
If a Tire Goes Flat
u
Temporarily Repairing a Flat Tire
Continued
Han
d
lin
g the U
n
expected
4. Recheck the air pressure using the sealant/
air hose on the compressor.
5. Turn the selector knob to AIR
*1
, AIR
ONLY
*2
, AIR SEULEMENT
*2
.
u
Do not turn the air compressor on to
check the pressure.
2 Inflating an Under-inflated Tire P. 531
6. If the air pressure is
• Less than 25 psi (175 kPa):
Do not add air or continue driving. The
leak is too severe. Call for help and have
your vehicle towed.
• 36 psi (250 kPa) or more:
Continue driving for another 10 minutes
or until you reach the nearest service
station, whichever is sooner. Do not
exceed 50 mph (80 km/h). If you have not
reached a service station after 10 minutes,
stop in a safe place and check the tire
pressure.
u
If the air pressure does not go down
after the 10 minute driving, you do not
need to check the pressure any more.
*1: U.S. models
*2: Canadian models
U.S.
Canada
Sealant/Air Hose
uu
If a Tire Goes Flat
u
Temporarily Repairing a Flat Tire
530
Han
d
lin
g the U
n
expected
• Greater than 25 psi (175 kPa), but less
than 36 psi (250 kPa):
Turn the air compressor on to inflate the
tire until the tire pressure reaches 36 psi
(250 kPa).
2 Inflating an Under-inflated Tire P. 531
Then drive carefully for 10 more minutes
or until you reach the nearest service
station, whichever is sooner. Do not
exceed 50 mph (80 km/h). If you have not
reached a service station after 10 minutes,
stop in a safe place and check the tire
pressure.
u
You should repeat this procedure as
long as the air pressure is within this
range.
7. Unplug the kit from the accessory power
socket.
8. Unscrew the air only hose from the tire
valve stem. Reinstall the valve cap.
9. Press the pressure relief button until the
gauge returns to 0 psi (0 kPa).
10. Repackage and properly stow the kit.
Pressure Relief Button
1
Distributing the Sealant in the Tire
3
WARNING
Running the engine with the vehicle in an
enclosed or even partly enclosed area can
cause a rapid build-up of toxic carbon
monoxide.
Breathing this colorless, odorless gas can
cause unconsciousness and even death.
Only run the engine to power the air
compressor with the vehicle outdoors.
Continued
531
uu
If a Tire Goes Flat
u
Temporarily Repairing a Flat Tire
Han
d
lin
g the U
n
expected
You can use the kit to inflate a non-punctured under-inflated tire.
1. Open the trunk floor lid.
2 Getting Ready to Temporarily Repair
2. Remove the kit from the case.
3. Place the kit, face up, on flat ground near
the flat tire, away from traffic. Do not
place the kit on its side.
4. Remove the air only hose from the kit.
5. Remove the valve cap.
6. Attach the sealant/air hose onto the tire
valve stem. Screw it until it is tight.
■
Inflating an Under-inflated Tire
1
Inflating an Under-inflated Tire
NOTICE
Do not operate the temporary tire repair kit
compressor for more than 15 minutes. The
compressor can overheat and become permanently
damaged.
Sealant/Air Hose
Valve Cap
Valve Stem
Sealant/Air Hose
uu
If a Tire Goes Flat
u
Temporarily Repairing a Flat Tire
532
Han
d
lin
g the U
n
expected
7. Plug in the kit to the accessory power
socket.
u
Be careful not to pinch the cord in a
door or window.
u
Do not plug any other electronic
devices into other accessory power
sockets.
2 Accessory Power Sockets P. 189
8. Turn the power system on.
u
Keep the power system on while
injecting air.
9. Turn the selector knob to AIR
*1
, AIR
ONLY
*2
, AIR SEULEMENT
*2
.
10. Press the inflator switch to turn on the kit.
u
The compressor starts to inject air into
the tire.
11. Inflate the tire to the specified air pressure.
*1: U.S. models
*2: Canadian models
1
Inflating an Under-inflated Tire
3
WARNING
Running the engine with the vehicle in an
enclosed or even partly enclosed area can
cause a rapid build-up of toxic carbon
monoxide.
Breathing this colorless, odorless gas can
cause unconsciousness and even death.
Only run the engine to power the air
compressor with the vehicle outdoors.
U.S.
Canada
533
uu
If a Tire Goes Flat
u
Temporarily Repairing a Flat Tire
Han
d
lin
g the U
n
expected
12. Turn off the kit.
u
Check the pressure gauge on the air
compressor.
u
If overinflated, press the pressure relief
button.
13. Unplug the kit from the accessory power
socket.
14. Unscrew the sealant/air hose from the tire
valve stem. Reinstall the valve cap.
15. Press the pressure relief button until the
gauge returns to 0 psi (0 kPa).
16. Repackage and properly stow the kit.
Pressure Relief Button
534
Han
d
lin
g the U
n
expected
Handling of the Jack
Your vehicle has jacking points as shown.
When replacing your tires, consult an authorized Honda Clarity Plug-In Hybrid
dealer.
Jacking Points
535
Continued
Han
d
lin
g the U
n
expected
Power System Won’t Start
Checking the Procedure
When the READY indicator does not come on and the Ready To Drive message
does not appear on the driver information interface, check the following items and
take appropriate action.
Checklist
Condition
What to Do
Check if the related
indicator or driver
information interface
messages come on.
The Remove Charger Connector message appears
Removing a charge connector. Set the power
mode to ACCESSORY, then to ON.
The Low Battery Charge. Power Reduced. message appears Charge the High Voltage battery.
The Temperature Is Too Cold For Vehicle To Operate
message appears.
2 Driver Information Interface Warning and
The To Start, Hold Remote Near Start Button message
appears.
u
Make sure the smart entry remote is in its operating range.
2 POWER Button Operating Range P. 158
2 If the Smart Entry Remote Battery is Weak
P. 537
The POWER SYSTEM indicator comes on.
Have your vehicle checked by an authorized
Honda Clarity Plug-In Hybrid dealer.
The transmission system indicator blinks and Transmission
Problem Apply Parking Brake When Parked message
appears.
The power system can be activated as a
temporary measure.
2 If the Transmission System Indicator Blinks
along with the Warning Message P. 552
Check the brightness
of the interior lights.
The interior lights are dim or do not come on at all.
Have the 12-volt battery checked by an
authorized Honda Clarity Plug-In Hybrid dealer.
The interior lights come on normally.
Check all fuses, or have your vehicle checked by
an authorized Honda Clarity Plug-In Hybrid
dealer.
2 Inspecting and Changing Fuses P. 560
1
If you must start the vehicle immediately, use an
assisting vehicle or booster battery to jump start it.
2 Jump Starting P. 539
536
uu
Power System Won’t Start
u
Checking the Procedure
Han
d
lin
g the U
n
expected
Checklist
Condition
What to Do
Check the Security
System Alarm
indicator.
When the Security System Alarm indicator is blinking, the power
system cannot be turned on.
2 Security System Alarm P. 153
537
uu
Power System Won’t Start
u
If the Smart Entry Remote Battery is Weak
Han
d
lin
g the U
n
expected
If the Smart Entry Remote Battery is Weak
If the beeper sounds, the To Start, Hold Remote Near Start Button message
appears on the driver information interface, and the POWER button flashes, the
READY indicator does not come on.
Turn on the power system as follows:
1. Touch the center of the POWER button
with the H logo on the smart entry remote
while the indicator on the POWER button is
flashing. The buttons on the smart entry
remote should be facing you.
u
The POWER button flashes for about 30
seconds.
2. Depress the brake pedal and press the
POWER button within 10 seconds after the
beeper sounds and the POWER button
changes from flashing to on.
u
If you do not depress the pedal, the
mode will change to ACCESSORY.
538
uu
Power System Won’t Start
u
Emergency Power System Off
Han
d
lin
g the U
n
expected
Emergency Power System Off
The POWER button may be used to turn the power system off due to an emergency
situation even while driving. If you must turn the power system off, do either of the
following operations:
• Press and hold the POWER button for about two seconds.
• Firmly press the POWER button three times.
The steering wheel will not lock. However, because turning off the power system
disables the power assist the power system provides to the steering and braking
systems, it will require significantly more physical effort and time to steer and slow
the vehicle. Use both feet on the brake pedal to slow down the vehicle and stop
immediately in a safe place.
The gear position automatically changes to
(
P after the vehicle comes to a complete
stop. Then, the power mode changes to VEHICLE OFF.
1
Do not press the button while driving unless it is
absolutely necessary for the power system to be
turned off.
539
Continued
Han
d
lin
g the U
n
expected
Jump Starting
Turn off the power to electric devices, such as the audio and lights. Turn off the
power system, then open the hood.
1. Open the battery terminal cover.
2. Connect the first jumper cable to your
vehicle’s 12-volt battery + terminal.
3. Connect the other end of the first jumper
cable to the booster battery + terminal.
u
If you use a booster battery, only use a
12-volt booster battery.
u
When using an automotive battery
charger, select a charging voltage lower
than 15-volts. Check the charger manual
for the proper setting.
4. Connect the second jumper cable to the
booster battery - terminal.
■
Jump Starting Procedure
1
Securely attach the jumper cable clips so that they do
not come off when the power system vibrates. Also
be careful not to tangle the jumper cables or allow
the cable ends to touch each other while attaching or
detaching the jumper cables.
12-volt Battery performance degrades in cold
conditions and may prevent the power system from
starting.
3
WARNING
A 12-volt battery can explode if you do not
follow the correct procedure, seriously
injuring anyone nearby.
Keep all sparks, open flames, and smoking
materials away from the 12-volt battery.
Battery Terminal Cover
Booster Battery
540
uu
Jump Starting
u
Han
d
lin
g the U
n
expected
5. Connect the other end of the second
jumper cable to the power system
mounting bolt as shown. Do not connect
this jumper cable to any other part of the
vehicle.
6. If your vehicle is connected to another
vehicle, start the assisting vehicle’s engine,
and increase its rpm slightly.
7. Attempt to start your vehicle’s power
system. If it does not turn on, check that the
jumper cables have good metal-to-metal
contact.
541
uu
Jump Starting
u
Han
d
lin
g the U
n
expected
Once your vehicle’s power system has started, remove the jumper cables in the
following order:
1. Disconnect the jumper cable from your vehicle’s ground.
2. Disconnect the other end of the jumper cable from the booster battery -
terminal.
3. Disconnect the jumper cable from your vehicle’s 12-volt battery + terminal.
4. Disconnect the other end of the jumper cable from the booster battery +
terminal.
Have your vehicle inspected by a nearby service station or an authorized Honda
Clarity Plug-In Hybrid dealer.
■
What to Do After the Power System Starts
1
What to Do After the Power System Starts
The indicators for the Vehicle Stability Assist (VSA®)
system, VSA® OFF, Collision Mitigation Braking
System
TM
(CMBS
TM
), and low tire pressure/Tire
Pressure Monitoring System (TPMS) may come on
along with a message in the driver information
interface when you turn the power system on after
reconnecting the battery.
Drive a short distance at 12 mph (20 km/h). The
indicator should go off. If it does not, have your
vehicle checked by an authorized Honda Clarity Plug-
In Hybrid dealer.
542
Han
d
lin
g the U
n
expected
Overheating
How to Handle Overheating
Overheating symptoms are as follows:
• The High Temperature. Power Reduced. message appears on the multi-
information display.
• The Stop Driving When Safe. Engine Temperature Too Hot message appears
on the multi-information display.
• Steam or spray comes out of the engine compartment.
The High Temperature. Power Reduced. message appears on the multi-
information display when the power system temperature is high.
2 Driver Information Interface Warning and Information Messages P. 103
1. Immediately park the vehicle in a safe place.
u
Change the gear position to
(
P, and set the parking brake. Turn off all
accessories and turn on the hazard warning lights.
2. Keep the power mode in ON, and wait until the message disappears.
u
If the message does not disappear, have the vehicle inspected at an authorized
Honda Clarity Plug-In Hybrid dealer.
■
The High Temperature. Power Reduced. Message Appears
on the Multi-Information Display
Continued
543
uu
Overheating
u
How to Handle Overheating
Han
d
lin
g the U
n
expected
■
First thing to do
1. Immediately park the vehicle in a safe place.
2. Turn off all accessories and turn on the hazard warning lights.
u
No steam or spray present: Keep the power system on and open the hood.
u
Steam or spray is present: Turn off the power system and wait until it
subsides. Then open the hood.
■
The Stop Driving When Safe. Engine Temperature Too Hot
Message Appears on the Multi-Information Display
1
NOTICE
Continuing to drive with the Stop Driving When
Safe. Engine Temperature Too Hot message on
the multi-information display may damage the
engine.
3
WARNING
Steam and spray from an overheated
engine can seriously scald you.
Do not open the hood if steam is coming
out.
uu
Overheating
u
How to Handle Overheating
544
Han
d
lin
g the U
n
expected
■
Next thing to do
1. Check that the cooling fan is operating and
turn the power system off once the Stop
Driving When Safe. Engine
Temperature Too Hot message
disappears.
u
If the cooling fan is not operating,
immediately turn the power system off.
2. Once the engine has cooled down, inspect
the coolant level and check the cooling
system components for leaks.
u
If the coolant level in the reserve tank is
low, add coolant until it reaches the
MAX mark.
u
If there is no coolant in the reserve tank,
check that the radiator is cool. Cover the
radiator cap with a heavy cloth and open
the cap. If necessary, add coolant up to
the base of the filler neck, and put the
cap back on.
■
Last thing to do
Once the engine has cooled sufficiently, turn the power system on.
If the Stop Driving When Safe. Engine Temperature Too Hot message does not
appear, resume driving. If it appears again, contact an authorized Honda Clarity
Plug-In Hybrid dealer for repairs.
1
If the coolant is leaking, contact an authorized Honda
Clarity Plug-In Hybrid dealer for repairs.
Use water as an emergency/temporary measure only.
Have an authorized Honda Clarity Plug-In Hybrid
dealer flush the system with proper antifreeze as
soon as possible.
3
WARNING
Removing the radiator cap while the
engine is hot can cause the coolant to spray
out, seriously scalding you.
Always let the engine and radiator cool
down before removing the radiator cap.
Reserve Tank
MAX
MIN
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст