Honda Clarity Plug-in Hybrid (2018 year). Manual — part 35
545
Han
d
lin
g the U
n
expected
Indicator, Coming On/Blinking
If the Low Oil Pressure Warning Appears
■
Reasons for the Warning to appear
Appears when the engine oil pressure is low.
■
What to do as soon as the warning
appears
1. Immediately park the vehicle on level
ground in a safe place.
2. If necessary, turn the hazard warning lights
on.
■
What to do after parking the vehicle
1. Stop the engine and let it sit for
approximately three minutes.
2. Open the hood and check the oil level.
3. Start the engine and check the low oil
pressure warning.
u
The warning disappears: Start driving
again.
u
The warning does not disappear within
10 seconds: Immediately stop the engine
and contact an authorized Honda Clarity
Plug-In Hybrid dealer for repairs.
1
If the Low Oil Pressure Warning Appears
NOTICE
Running the engine with low oil pressure can cause
serious mechanical damage almost immediately.
546
uu
Indicator, Coming On/Blinking
u
If the 12-Volt Battery Charging System Indicator Comes On
Han
d
lin
g the U
n
expected
If the 12-Volt Battery Charging System Indicator
Comes On
■
Reasons for the indicator to come on
Comes on when the 12-volt battery is not being charged.
■
What to do when the indicator comes on
Turn off the climate control system, rear defogger, and other electrical
systems, and immediately contact an authorized Honda Clarity Plug-In
Hybrid dealer for repairs.
1
If the 12-Volt Battery Charging System Indicator Comes On
If you need to stop temporarily, do not turn off the
power system. Restarting the power system may
rapidly discharge the battery.
547
uu
Indicator, Coming On/Blinking
u
If the Malfunction Indicator Lamp Comes On or Blinks
Han
d
lin
g the U
n
expected
If the Malfunction Indicator Lamp Comes On or
Blinks
■
Reasons for indicator lamp to come on or blink
• Comes on when there is a problem with the engine emissions control
system, or the fuel fill cap is missing, or loose.
• Blinks when engine misfiring is detected.
■
What to do when the indicator lamp comes on
Avoid high speeds and immediately get your vehicle inspected at an
authorized Honda Clarity Plug-In Hybrid dealer.
■
What to do when the indicator lamp blinks
Park the vehicle in a safe place with no flammable items and wait at least
10 minutes or more with the power system stopped until it cools.
■
The message appears on when:
An evaporative system leak is detected. This may be caused by the fuel fill cap being
loose or not being installed.
■
What to do when the message appears:
1. Stop the power system.
2. Check if the fuel fill cap is fully installed.
u
If not, loosen the cap, and then retighten it until it clicks at least once.
3. Drive for several days of normal driving.
u
The message should go off.
■
When the malfunction indicator lamp comes on
The malfunction indicator lamp comes on if the system continues to detect a leak of
gasoline vapor. If this happens, follow the procedures described earlier to check the
fuel fill cap.
■
Tighten Fuel Cap Message
1
If the Malfunction Indicator Lamp Comes On or Blinks
NOTICE
If you drive with the malfunction indicator lamp on,
the emissions control system and the engine could be
damaged.
If the malfunction indicator lamp blinks again when
restarting the engine, drive to the nearest an
authorized Honda Clarity Plug-In Hybrid dealer at 31
mph (50 km/h) or less. Have your vehicle inspected.
548
uu
Indicator, Coming On/Blinking
u
If the Brake System Indicator (Red) Comes On or Blinks
Han
d
lin
g the U
n
expected
If the Brake System Indicator (Red) Comes On or
Blinks
■
Reasons for the indicator to come on
• The brake fluid is low.
• There is a malfunction in the brake system.
■
What to do when the indicator comes on while driving
Depress the brake pedal lightly to check pedal pressure.
• If normal, check the brake fluid level the next time you stop.
• If abnormal, take immediate action. If necessary, slow the vehicle
using the deceleration paddle selector.
■
Reason for the indicator to blink
• There is a problem with the electric parking brake system.
■
What to do when the indicator blinks
Avoid using the parking brake and have your vehicle checked by an
authorized Honda Clarity Plug-In Hybrid dealer immediately.
1
If the Brake System Indicator (Red) Comes On or Blinks
Have your vehicle repaired immediately.
It is dangerous to drive with low brake fluid. If there
is no resistance from the brake pedal, stop
immediately in a safe place. If necessary, downshift
the gears.
If the brake system indicator and ABS indicator come
on simultaneously, the electronic brake distribution
system is not working. This can result in vehicle
instability under sudden braking.
Have your vehicle inspected by an authorized Honda
Clarity Plug-In Hybrid dealer immediately.
If the brake system indicator (red) blinks at the same
time when the brake system indicator (amber) comes
on, the parking brake may not work.
Avoid using the parking brake and have your vehicle
checked by an authorized Honda Clarity Plug-In
Hybrid dealer immediately.
2 If the Brake System Indicator (Red) Comes
On or Blinks at the Same Time When the
Brake System Indicator (Amber) Comes On
P. 550
U.S.
Canada
549
uu
Indicator, Coming On/Blinking
u
If the Electric Power Steering (EPS) System Indicator Comes On
Han
d
lin
g the U
n
expected
If the Electric Power Steering (EPS) System Indicator
Comes On
■
Reasons for the indicator to come on
• Comes on when there is a problem with the EPS system.
• If you depress the accelerator pedal repeatedly to increase the motor
speed while the motor is idling, the indicator comes on, and
sometimes the steering wheel becomes harder to operate.
• Comes on when the EPS steering angle center point memory is lost.
This could be due to a number of problems including: battery
disconnection, main fuse blow, low battery causing the reset of the
EPS system, wire damage to EPS harness. Vehicle Stability Assist
(VSA®), VSA® OFF, Collision Mitigation Braking System
TM
(CMBS
TM
),
and low tire pressure/TPMS indicators come on along with a message
in the driver information interface.
■
What to do when the indicator comes on
• Stop the vehicle in a safe place, turn off the power system, and turn
on the power system again.
If the indicator re-appears and stays on, immediately have your vehicle
inspected by an authorized Honda Clarity Plug-In Hybrid dealer.
• If VSA® indicator, VSA® OFF indicator, CMBS
TM
indicator, and low tire
pressure/TPMS indicator come on along with a message in the driver
information interface, you need to calibrate the VSA and EPS systems.
Drive a short distance at more than 12 mph (20 km/h) to calibrate the
VSA and EPS systems.
If the indicators come on and stay on, park your vehicle in a safe
place, turn off and turn on the power system, then repeat the above
operation.
If the indicators still come on and stay on, immediately have your
vehicle inspected by an authorized Honda Clarity Plug-In Hybrid dealer.
550
uu
Indicator, Coming On/Blinking
u
If the Brake System Indicator (Red) Comes On or Blinks at the Same Time When the Brake System Indicator (Amber) Comes On
Han
d
lin
g the U
n
expected
If the Brake System Indicator (Red) Comes On or
Blinks at the Same Time When the Brake System
Indicator (Amber) Comes On
■
If the brake system indicator (red) comes on or blinks at the
same time when the brake system indicator (amber) comes on,
release the parking brake manually or automatically.
2 Parking Brake P. 431
• If the brake system indicator (red) continuously comes on or blinks at
the same time the brake system indicator (amber) comes on, stop the
vehicle in a safe place, and have it inspected by an authorized Honda
Clarity Plug-In Hybrid dealer immediately.
u
Prevents the vehicle from moving gear position to
(
P.
• If only the Brake System Indicator (Red) is turned off, avoid using the
parking brake, and have your vehicle checked by an authorized
Honda Clarity Plug-In Hybrid dealer immediately.
1
If you apply the parking brake, you may not be able
to release it.
If the brake system indicator (red) and the brake
system indicator (amber) come on at the same time,
the parking brake is working.
If the brake system indicator (red) blinks at the same
time when the brake system indicator (amber) comes
on, the parking brake may not work because it is
checking the system.
U.S.
Canada
U.S.
Canada
(Red)
(Red)
(Amber)
(Amber)
551
uu
Indicator, Coming On/Blinking
u
If the Low Tire Pressure/TPMS Indicator Comes On or Blinks
Han
d
lin
g the U
n
expected
If the Low Tire Pressure/TPMS Indicator Comes On or
Blinks
■
Reasons for the indicator to come on or blink
A tire pressure is significantly low, or the TPMS has not been calibrated.
If there is a problem with the TPMS, the indicator blinks for about one
minute, and then stays on.
■
What to do when the indicator comes on
Drive carefully and avoid abrupt cornering and hard braking.
Stop your vehicle in a safe place. Check the tire pressure and adjust the
pressure to the specified level. The specified tire pressure is on a label on
the driver’s side doorjamb.
u
Calibrate the TPMS after the tire pressure is adjusted.
■
What to do when the indicator blinks, then remains on
Have the tire inspected by an authorized Honda Clarity Plug-In Hybrid
dealer as soon as possible.
1
If the Low Tire Pressure/TPMS Indicator Comes On or Blinks
NOTICE
Driving on an extremely underinflated tire can cause
it to overheat. An overheated tire can fail. Always
inflate your tires to the prescribed level.
552
uu
Indicator, Coming On/Blinking
u
If the Transmission System Indicator Blinks along with the Warning Message
Han
d
lin
g the U
n
expected
If the Transmission System Indicator Blinks along
with the Warning Message
■
Reasons for the indicator to blink
The transmission is malfunctioning.
■
What to do when the indicator blinks
• Immediately have your vehicle inspected by
an authorized Honda Clarity Plug-In Hybrid
dealer.
• Change the gear position to
(
N when you
turn the power system on.
u
Check if the
(
N position in the
instrument panel and the indicator on
the
(
N button light/blink.
u
The power system cannot be turned on
unless the parking brake is set.
1
If the Transmission System Indicator Blinks along with the
Warning Message
You may not be able to turn on the power system.
Make sure to set the parking brake when parking
your vehicle.
Call a professional towing service if you need to tow
your vehicle.
2 Emergency Towing P. 561
553
Continued
Han
d
lin
g the U
n
expected
Fuses
Fuse Locations
If any electrical devices are not working, set
the power mode to VEHICLE OFF (LOCK),
and check to see if any applicable fuse is
blown.
There are three fuse boxes in the engine
compartment.
Fuse locations are shown on the fuse box
cover. Locate the fuse in question by the
fuse number and box cover number.
■
Fuse box A
Located near the windshield washer
reservoir. Push the tabs to open the box.
■
Engine Compartment Fuse
Box
Tab
■
Circuit protected and fuse rating
Circuit Protected
Amps
1
BATTERY
175 A
2
EPS
70 A
ESB
40 A
IG MAIN (SMART)
30 A
ABS/VSA MOTOR
40 A
WIPER MOTOR 1
30 A
ABS/VSA FSR
40 A
−
30 A
3
Engine EWP
30 A
SUB FUSE BOX 2-1
30 A
SUB FUSE BOX 3-2
30 A
IG MAIN 2
30 A
4
IG COIL
15 A
5
H/L LO MAIN
15 A
6
EVTC
20 A
7
DTWP
10 A
8
DBW
15 A
9
VBU
10 A
10
STOP LIGHT
7.5 A
11
IGP
15 A
12
FUSE BOX MAIN 1
60 A
FUSE BOX MAIN 2
40 A
FUSE BOX MAIN 3
50 A
H/L HI MAIN
30 A
SMALL MAIN
20 A
SUB FUSE BOX 4
(30 A)
−
30 A
WIPER MOTOR 2
30 A
−
30 A
−
30 A
13
HEATER MOTOR
40 A
14
REAR DEFROSTER
40 A
15
−
−
16
BATT SNSR
7.5 A
17
ES EWP
15 A
18
A/C MAIN/DRL
10 A
19
ES VLV
7.5 A
20
HORN
10 A
21
BACK UP
10 A
22
AUDIO
15 A
23
IGPS (LAF)
10 A
24
R H/L LO
7.5 A
25
L H/L LO
7.5 A
26
IGPS
10 A
Circuit Protected
Amps
554
uu
Fuses
u
Fuse Locations
Han
d
lin
g the U
n
expected
■
Fuse box B
Tab
Pull up the cover on the + terminal, then
remove it while pulling out the tab as
shown.
Replacement of engine compartment fuses
should be done by an authorized Honda
Clarity Plug-In Hybrid dealer.
■
Circuit protected and fuse rating
Circuit Protected
Amps
a
MAIN
200 A
b
RB MAIN 1
70 A
c
RB MAIN 2
80 A
d
GLOW
60 A
555
uu
Fuses
u
Fuse Locations
Continued
Han
d
lin
g the U
n
expected
■
Fuse Box C
Located near the fuse box B.
Fuse locations are shown on the fuse box
cover. Locate the fuse in question by the
fuse number and box cover number.
Tab
■
Circuit protected and fuse rating
Circuit Protected
Amps
1
RFC1
30 A
2
RFC2
30 A
3
P-ACT
30 A
4
IGB RFC1
7.5 A
5
IGB RFC2
7.5 A
556
uu
Fuses
u
Fuse Locations
Han
d
lin
g the U
n
expected
There are four fuse boxes on the driver’s
side.
■
Fuse Box A
Located under the dashboard.
Fuse locations are shown on the label on
the under panel.
Locate the fuse in question by the fuse
number and label number.
■
Driver’s Side Interior Fuse Box
Fuse Label
Fuse Box A
■
Circuit protected and fuse rating
Circuit Protected
Amps
1
ACC
7.5 A
2
−
−
3
VB SOL
10 A
4
SHIFTER
7.5 A
5
OPTION MAIN
15 A
6
SRS OPTION
7.5 A
7
METER
10 A
8
FUEL PUMP
15 A
9
OPTION
7.5 A
10
CTR ACC SOCKET
20 A
11
−
−
12
R SIDE DOOR LOCK
10 A
13
L SIDE DOOR UNLOCK
10 A
14
RR L P/W
20 A
15
AS P/W
20 A
16
DOOR LOCK
20 A
17
P-DRV
7.5 A
18
−
−
19
WASHER
15 A
20
−
−
21
ACG
7.5 A
22
DRL
7.5 A
23
−
10 A
24
FR SENSOR CAMERA
5 A
25
DR DOOR LOCK
10 A
26
R SIDE DOOR UNLOCK
10 A
27
RR R P/W
20 A
28
DR P/W
20 A
29
FR ACC SOCKET
20 A
30
INTERIOR LIGHT
7.5 A
31
DR P/SEAT REC
20 A
32
FR SEAT HEATER
20 A
33
DR P/SEAT SLI
20 A
34
ABS/VSA
7.5 A
35
SRS
10 A
36
−
−
37
LID ACT
10 A
38
L SIDE DOOR LOCK
10 A
39
DR DOOR UNLOCK
10 A
Circuit Protected
Amps
557
uu
Fuses
u
Fuse Locations
Continued
Han
d
lin
g the U
n
expected
■
Fuse Box B
Located under the fuse box A.
Fuse locations are shown on the label on
the under panel.
Locate the fuse in question by the fuse
number and label number.
Fuse Label
Fuse Box B
■
Circuit protected and fuse rating
Circuit Protected
Amps
c
QC CNT
(10 A)
d
R H/L HI
7.5 A
e
L H/L HI
7.5 A
f
IGC
10 A
g
HAZARD
10 A
h
IGB
15 A
i
SMART
10 A
j
IGA
10 A
558
uu
Fuses
u
Fuse Locations
Han
d
lin
g the U
n
expected
■
Fuse Box C
Located on the right side of fuse box B.
Fuse locations are shown on the label on
the under panel.
Locate the fuse in question by the fuse
number and label number.
Fuse Label
Fuse Box C
■
Circuit protected and fuse rating
Circuit Protected
Amps
k
AS P/SEAT REC
(20 A)
l
AS P/SEAT SLIDE
(20 A)
m
ILLUMI
7.5 A
n
SMALL
7.5 A
559
uu
Fuses
u
Fuse Locations
Han
d
lin
g the U
n
expected
■
Fuse Box D
Located inside the driver’s side outer panel.
Replacement of fuses in the driver’s side
outer panel should be done by an
authorized Honda Clarity Plug-In Hybrid
dealer.
Fuse Box D
■
Circuit protected and fuse rating
Circuit Protected
Amps
p
COMBO
(10 A)
q
IGMG
(7.5 A)
r
SHIFTER
7.5 A
s
P-ACT DRV
7.5 A
t
−
−
u
EPP
(7.5 A)
v
OPTION
7.5 A
w
ESB
7.5 A
560
uu
Fuses
u
Inspecting and Changing Fuses
Han
d
lin
g the U
n
expected
Inspecting and Changing Fuses
1. Set the power mode to VEHICLE OFF
(LOCK). Turn headlights and all accessories
off.
2. Check the fuses on the battery in the
engine compartment.
u
If the fuse is blown, have it replaced by
an authorized Honda Clarity Plug-In
Hybrid dealer.
3. Remove the fuse box cover.
4. Check the large fuse in the engine
compartment.
u
If the fuse is blown, use a Phillips-head
screwdriver to remove the screw, and
replace it with a new one.
5. Inspect the small fuses in the engine
compartment and the vehicle interior.
u
If there is a blown fuse, remove it with
the fuse puller, and replace it with a new
one.
1
NOTICE
Replacing a fuse with one that has a higher rating
greatly increases the chances of damaging the
electrical system.
Replace the fuse with a spare fuse of the same
specified amperage.
Confirm the specified amperage using the charts on
P. to 559.
There is a fuse puller on the back of the cover of the
engine compartment fuse box A.
12-Volt Battery
Blown Fuse
Fuse Puller
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст