Lexus GS300/400 (2000 year). Service manual — part 253
RS082–01
RS–66
–
SUPPLEMENTAL RESTRAINT SYSTEM
SIDE AIRBAG SENSOR ASSEMBLY
2297
REPLACEMENT
REPLACEMENT REQUIREMENTS
In the following cases, replace the side airbag sensor assembly.
If the side airbag sensor assembly has been deployed in a collision.
If the side airbag sensor assembly has been found to be faulty in troubleshooting.
If the side airbag sensor assembly has been dropped.
CAUTION:
For removal and installation of the side airbag sensor assembly, see page
Be sure to follow the correct procedure.
RS083–01
H02619
–
SUPPLEMENTAL RESTRAINT SYSTEM
SIDE AIRBAG SENSOR ASSEMBLY
RS–67
2298
INSTALLATION
NOTICE:
Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.
Never reuse the side airbag sensor assembly in-
volved in a collision when the airbag has deployed.
Never repair a sensor in order to reuse it.
1.
INSTALL SIDE AIRBAG SENSOR
(a)
Using a torx wrench, install the side airbag assembly with
4 screws.
Torx wrench: T40 (Part No.09042–00020 or locally
manufactured tool)
Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
(b)
Connect the connector.
NOTICE:
Make sure the sensor assembly is installed to the
specified torque.
If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.
When installing the sensor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.
After installation, shake the sensor assembly to
check that there is no looseness.
2.
INSTALL FRONT SEAT OUTER BELT RETRACTOR
(See page
)
(a)
Install the retractor with 2 bolts.
HINT:
After tightening the upper bolt, tighten the lower bolt.
Torque:
Upper bolt: 7.4 N·m (75 kgf·cm, 65 in.·lbf)
Lower bolt: 41 N·m (420 kgf·cm, 30 ft·lbf)
(b)
w/ Seat Belt Warning:
Connect the retractor switch connector.
(c)
w/ Seat Belt Pretensioner:
Connect the pretensioner connector.
3.
INSTALL THESE PARTS:
(a)
Center pillar lower garnish
(b)
Rear door scuff plate
(c)
Front door scuff plate
RS084–01
H02621
Combination Meter
(Warning Light)
Steering Wheel Pad
(with Airbag)
Spiral Cable
RH Front Airbag Sensor
Front Passenger Airbag Assembly
RH Side Airbag
Assembly
RH Side Airbag
Sensor Assembly
RH Seat Belt
Pretensioner
Airbag Sensor Assembly
LH Side Airbag
Assembly
LH Seat Belt
Pretensioner
LH Side Airbag
Sensor Assembly
LH Front Airbag
Sensor
RS–68
–
SUPPLEMENTAL RESTRAINT SYSTEM
WIRE HARNESS AND CONNECTOR
2299
WIRE HARNESS AND CONNECTOR
LOCATION
RS085–01
–
SUPPLEMENTAL RESTRAINT SYSTEM
WIRE HARNESS AND CONNECTOR
RS–69
2300
INSPECTION
HINT:
The SRS wire harness is integrated with the instrument panel wire harness assembly. The wires for the SRS
wire harness are encased in a yellow corrugated tube and all the connectors in the system are a standard
yellow color.
1.
VEHICLE NOT INVOLVED IN COLLISION
Do a diagnostic system check.
(See page
2.
VEHICLE INVOLVED IN COLLISION
(a)
Do a diagnostic system check.
(See page
)
(b)
Check breaks in all wires of the SRS wire harness, and exposed conductors.
(c)
Check to see if the SRS wire harness connectors are cracked or chipped.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст