Chrysler Voyager. Manual — part 386
Symptom:
FR WIPER HI-LO RELAY OPEN
POSSIBLE CAUSES
FUSED B(+) CIRCUIT
COMMON CIRCUIT OPEN
WIPER HI/LOW RELAY
WIPER ON/OFF RELAY
WIPER HI/LOW RELAY CONTROL CIRCUIT OPEN
FCM-ON/OFF RELAY DRIVER OPEN
TEST
ACTION
APPLICABILITY
1
Turn the ignition off.
Remove the Wiper On/Off Relay from the PDC.
Using a 12-volt test light connected to ground, probe both Fused B(+) circuits in the
PDC.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly at each terminal?
All
Yes
→ Go To 2
No
→ Repair the Fused B(+) circuit(s) for an open.
Perform BODY VERIFICATION TEST - VER 1.
2
Install a substitute relay in place of the Wiper On/Off Relay.
Turn the ignition on.
Turn the wipers on.
Does the system operate correctly?
All
Yes
→ Replace the Wiper On/Off Relay.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
3
Turn the ignition off.
Remove the wiper High/Low Relay from the PDC.
Remove the wiper On/Off Relay from the PDC.
Measure the resistance of the Common circuit between the High/Low Relay and the
On/Off relay in the PDC.
Is the resistance below 10.0 ohms?
All
Yes
→ Go To 4
No
→ Repair the Common circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
4
Install a substitute relay in place of the Wiper Hi/Low Relay.
Turn the ignition on.
Turn the wipers on.
Does the system operate correctly?
All
Yes
→ Replace the Wiper Hi/Low Relay.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 5
971
WINDSHIELD WIPER & WASHER
TEST
ACTION
APPLICABILITY
5
Turn the ignition off.
Remove the Wiper Hi/Low Relay from the PDC.
Disconnect the FCM from the IPM.
Connect a jumper wire between the Wiper Hi/Low Relay Control circuit at the IPM
connector to ground.
Measure the resistance between ground and the Wiper Hi/Low Relay Control circuit
in the PDC.
Is the resistance below 5.0 ohms?
All
Yes
→ Replace the Front Control Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Repair the Wiper Hi/Low Relay Control circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
972
WINDSHIELD WIPER & WASHER
FR WIPER HI-LO RELAY OPEN —
Continued
Symptom:
FR WIPER HI-LO RELAY SHORT TO BATT
POSSIBLE CAUSES
WIPER HI/LOW RELAY
WIPER HI/LOW RELAY CONTROL CIRCUIT SHORTED TO VOLTAGE
FCM
TEST
ACTION
APPLICABILITY
1
Turn the ignition off.
Remove the Wiper Hi/Low Relay from the PDC.
Disconnect the FCM from the IPM.
Turn the ignition on.
Measure the voltage of the Wiper Hi/Low Relay Control circuit at the PDC connector.
Is the voltage above 1.0 volt?
All
Yes
→ Repair the Wiper Hi/Low Relay Control circuit for a short to
voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Install a substitute relay in place of the Wiper Hi/Low Relay.
Turn the ignition on.
Turn the wipers on.
Does the system operate correctly?
All
Yes
→ Replace the Wiper Hi/Low Relay.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Front Control Module.
Perform BODY VERIFICATION TEST - VER 1.
973
WINDSHIELD WIPER & WASHER
Symptom:
FRONT WASH SWITCH INPUT STUCK
POSSIBLE CAUSES
HIGH BEAM/FRONT WASHER SWITCH MUX CIRCUIT SHORTED TO GROUND
MULTI-FUNCTION SWITCH
WIRING HARNESS INSPECTION
FCM
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRB, select Body, Front Control Module and read the F Washer Switch
state.
Does the DRB display switch state as Closed?
All
Yes
→ Go To 2
No
→ Go To 4
2
Turn the ignition off.
Disconnect the Multi-Function Switch harness connector.
Turn the ignition on.
With the DRB, select Body, Front Control Module and read the F Washer Switch
state.
Does the DRB display switch state as Open?
All
Yes
→ Replace the Multi-Function Switch.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
3
Turn the ignition off.
Disconnect the Multi-Function Switch harness connector.
Disconnect the BCM C5 harness connector.
Measure the resistance between ground and the High Beam/Front Washer Switch
MUX circuit.
Is the resistance below 1000.0 ohms?
All
Yes
→ Repair the High Beam/Front Washer Switch MUX circuit for a
short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Front Control Module.
Perform BODY VERIFICATION TEST - VER 1.
974
WINDSHIELD WIPER & WASHER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст