Chrysler Voyager. Manual — part 387
TEST
ACTION
APPLICABILITY
4
Turn the ignition on.
With the DRBIII
t, erase all BCM and FCM DTCs.
Turn the ignition off.
NOTE: Visually inspect the related wiring harness and circuits. Look for
any chafed, pierced, pinched, or partially broken wires.
NOTE: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
Note: Refer to any Technical Service Bulletins (TSB) that may apply.
Were any problems found?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
975
WINDSHIELD WIPER & WASHER
FRONT WASH SWITCH INPUT STUCK —
Continued
Symptom:
FRONT WASHER OUTPUT OPEN
POSSIBLE CAUSES
INTERMITTENT WIRING AND CONNECTORS
FRONT WASHER MOTOR CONTROL CIRCUIT OPEN
FUSED ACCESSORY RELAY OUTPUT CIRCUIT
FRONT WASHER MOTOR CONTROL CIRCUIT SHORT TO VOLTAGE
FRONT WASHER PUMP MOTOR
FRONT CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Ignition on, engine off.
Press the Front Washer Switch.
Does the Front Washer Motor Function?
All
Yes
→ Go To 2
No
→ Go To 3
2
Turn the ignition on.
With the DRBIII
t, erase all BCM and FCM DTCs.
Turn the ignition off.
The conditions necessary to set this DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
Were there any problems found?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
3
Turn the ignition off to the lock position.
Disconnect the Front Washer Pump Motor harness connector.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine off.
Using a 12-volt test light connected to ground, check the Fused Accessory Relay
Output circuit in the Front Washer Pump Motor harness connector.
Does the test light illuminate brightly?
All
Yes
→ Go To 4
No
→ Repair the Fused Accessory Relay Output circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
976
WINDSHIELD WIPER & WASHER
TEST
ACTION
APPLICABILITY
4
Turn the ignition off to the lock position.
Disconnect the Front Washer Pump Motor harness connector.
Ignition on, engine off.
Using a 12-volt test light connected to 12 Volts, check the Front Washer Pump Motor
Control circuit in the Front Washer Pump Motor harness connector while pressing
the Front Washer Switch.
Does the test light illuminate brightly?
All
Yes
→ Replace the Front Washer Pump Motor in accordance with the
Service Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 5
5
Turn the ignition off to the lock position.
Disconnect the Front Control Module harness connector.
Disconnect the Front Washer Pump Motor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Rear Washer Pump Motor Control Circuit from the
Front Control Module connector to the Rear Washer Pump Motor harness connector.
Is the resistance above 5.0 ohms?
All
Yes
→ Repair the Front Washer Pump Motor Control Circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 6
6
Turn the ignition off to the lock position.
Disconnect the Front Control Module connector.
Disconnect the Front Washer Pump Motor harness connector.
Note: Check connectors - Clean/repair as necessary.
Turn the ignition on.
Using a 12-volt test light connected to ground, check the Front Washer Pump Motor
Control circuit.
Does the test light illuminate brightly?
All
Yes
→ Repair the Front Washer Pump Motor Control Circuit for a short
to voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Front Control Module in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
977
WINDSHIELD WIPER & WASHER
FRONT WASHER OUTPUT OPEN —
Continued
Symptom:
FRONT WIPER NOT PARKED
POSSIBLE CAUSES
FRONT CONTROL MODULE
FRONT WIPER MODULE
MECHANICAL PROBLEM
WIRING HARNESS INSPECTION
FRONT WIPER PARK SWITCH SENSE CIRCUIT OPEN
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRB, select Body, Front Control Module, Inputs/Outputs and read the
Wiper Park Sw state.
Does the DRB display Closed?
All
Yes
→ Go To 2
No
→ Go To 3
2
Turn the ignition on.
With the DRBIII
t, erase all BCM and FCM DTCs.
Turn the ignition off.
NOTE: Visually inspect the related wiring harness and circuits. Look for
any chafed, pierced, pinched, or partially broken wires.
NOTE: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
Note: Refer to any Technical Service Bulletins (TSB) that may apply.
Were any problems found?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
3
Turn the ignition off.
Inspect all of the moving components associated with the Front Wiper system. Look
for broken or damaged components which may prevent the wipers from parking
properly.
Are the any mechanical problems?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
978
WINDSHIELD WIPER & WASHER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст