Dodge Durango SRT (2019 year). Instruction — part 32

This feature will automatically deactivate after extended
driving at road speeds, or when one or more of the
following conditions apply:
• If coolant temperatures reaches the target temperature

and cooling is no longer required.

• If battery voltage or state of charge drops below a

threshold.

• The hood is opened.

VALET MODE

To enter Valet Mode press the “Valet” button on the
touchscreen and a popup screen will ask you if you would
like to enter Valet Mode, after selecting “Yes” you will be
asked to enter a four digit PIN code. The PIN code is not
set, so you are free to select any four digit numeric
combination that will be easy to remember.

Valet Mode Activation

10

MULTIMEDIA

509

While in Valet Mode the following vehicle configurations
are set and locked to prevent unauthorized modification:
• All-Wheel Drive is set to 50/50.
• Transmission locks out access to first gear and up-shifts

earlier than normal.

• Steering wheel paddle shifters are disabled.
• The Drive Mode interface is not available. Pushing the

SRT button on the console will display the unlock
keypad.

• The ESC Off button is disabled.
• The Launch Control button is disabled.
• Engine power is reduced.

To exit Valet Mode you must enter the same four digit PIN
that was used to enter the mode. The unlock keypad can be
accessed by either pushing the SRT button, or pressing the
“Valet” button on the touchscreen.

Valet Mode Deactivation

510

MULTIMEDIA

The Valet Mode Deactivation key pad will then prompt
you for your four digit PIN code, enter your PIN code and
press the “OK” button on the touchscreen.

NOTE:

If your four digit PIN is lost or forgotten, the

vehicle will exit Valet Mode after a battery disconnect for
approximately five minutes. Reconnect the battery and
cycle the ignition to the RUN position, the vehicle will be in
Auto Mode.

ECO MODE

Push the ECO button on the touchscreen to enter ECO
mode. ECO mode modifies the vehicle’s engine and trans-
mission settings to provide improved fuel economy at a
trade-off with acceleration performance. Increased engine
exhaust noise and/or vibration may be noticed while ECO
is active. This is normal and a result of the increased

Valet Mode Deactivation PIN

Eco Mode

10

MULTIMEDIA

511

amount of operating conditions where the vehicle is al-
lowed to operate in four cylinder shutoff mode.

The Paddle Shifters will be disabled while in ECO mode.
• ECO will be disabled when another Drive Mode is

selected or ECO button is pushed.

STEERING WHEEL AUDIO CONTROLS —
IF EQUIPPED

The remote sound system controls are located on the rear
surface of the steering wheel. Reach behind the wheel to
access the switches.

The right-hand control is a rocker-type switch with a
push-button in the center and controls the volume and
mode of the sound system. Pushing the top of the rocker
switch increases the volume, and pushing the bottom of the
rocker switch decreases the volume.

Pushing the center button makes the radio switch between
the various modes available (AM/FM/SXM or Media etc.)

The left-hand control is a rocker-type switch with a push-
button in the center. The function of the left-hand control is
different depending on which mode you are in.

The following describes the left-hand control operation in
each mode.

Radio Operation

Pushing the top of the switch will “Seek” up for the next
listenable station and pushing the bottom of the switch will
“Seek” down for the next listenable station.

The button located in the center of the left-hand control
will tune to the next preset station that you have pro-
grammed in the radio preset button.

Steering Wheel Audio Controls
(Back View Of Steering Wheel)

512

MULTIMEDIA

Media Mode

Pushing the top of the switch once goes to the next track on
the selected media (AUX/USB/Bluetooth). Pushing the
bottom of the switch once goes to the beginning of the
current track, or to the beginning of the previous track if it
is within eight seconds after the current track begins to
play.

IPOD/USB/MP3 CONTROL — IF EQUIPPED

This feature allows an iPod or external USB device to be
plugged into the USB port, located inside the storage area
on the center stack of the instrument panel.

iPod control supports Mini, 4G, Photo, Nano, 5G iPod and
iPhone devices. Some iPod software versions may not fully
support the iPod control features. Please visit Apple’s
website for software updates.

For further information, refer to the Uconnect Owner’s
Instruction Supplement.

Connecting The iPod Or External USB Device

Use the connection cable to connect an iPod or external
USB device to the vehicles USB/AUX connector port which
is located in the center console.

The USB ports on the Media Hub are equipped with a
Smart Electronic Voltage Regulator (Smart Charge) feature.
This feature allows a device to charge for up to one hour
after the vehicle is powered off.

Once the audio device is connected and synchronized to
the vehicles iPod/USB/MP3 control system (iPod or exter-
nal USB device may take a few minutes to connect), the
audio device starts charging and is ready for use.

NOTE:

If the audio device battery is completely discharged,

it may not communicate with the iPod/USB/MP3 control
system until a minimum charge is attained. Leaving the

Integrated Center Console USB/AUX Media HUB

10

MULTIMEDIA

513

audio device connected to the iPod/USB/MP3 control sys-
tem may charge it to the required level.

Using This Feature

By using an iPod cable, or an external USB device to
connect to the USB port:
• The audio device can be played on the vehicle’s sound

system, providing metadata (artist, track title, album,
etc.) information on the radio display.

• The audio device can be controlled using the radio

buttons to Play, Browse, and List the iPod contents.

• The audio device battery charges when plugged into the

USB/AUX connector (if supported by the specific audio
device).

NOTE:

For further information, refer to the Uconnect

Owner’s Instruction Supplement.

Second Row USB Charging Port

Second row USB connector ports can be used for charging
purposes only. Use the connection cable to connect an iPod
or external USB device to the vehicle’s USB charging ports
which are located either on the rear of the front center
console and/or in the second row center console.

Front Center Console Rear USB Ports

Second Row Center Console USB Port

514

MULTIMEDIA

UCONNECT REAR SEAT ENTERTAINMENT (RSE)
SYSTEM — IF EQUIPPED

Your Rear Seat Entertainment System is designed to give
your family years of enjoyment. You can play your favorite
CDs, DVDs or Blu-ray Discs, listen to audio over the
wireless headphones, or plug and play a variety of stan-
dard video games or audio devices.

Please review this Owner’s Instruction to become familiar
with its features and operation.

Getting Started
• Screen(s) located in the rear of front seats: Open the

LCD screen cover by lifting up on the cover.

• Place the ignition in the ON or ACC position.
• Your vehicle may be equipped with a Blu-ray disc

player. If equipped with a Blu-ray disc player, the icon
will be present on the player.

• Turn on the Rear Seat Entertainment system by pushing

the power button on the remote control.

• When the Video Screen(s) are open and a DVD/Blu-ray

disc is inserted into the disc player, the screen(s) turn(s)
on automatically, the headphone transmitters turn on
and playback begins.

RSE System Screen

10

MULTIMEDIA

515

• With the Dual Video Screen System, Channel 1 (Rear 1)

on the remote control and headphones, refers to Screen
1 (driver’s side) and Channel 2 (Rear 2) on the Remote
Control and Headphones refers to Screen 2 (passenger
side).

RSE System Channel 1 (Rear 1)

RSE System Remote Control Channel Selectors

RSE System Headphone Channel Selectors

516

MULTIMEDIA

• The system can be controlled either by the front seat

occupants utilizing the touchscreen radio or by the rear
seat occupants using the remote control.

Dual Video Screen

NOTE:

Typically there are two different ways to operate

the features of the Rear Seat Entertainment System.
• The Remote Control
• The Touchscreen Radio (If Equipped)

Blu-ray Disc Player

Play A Blu-ray Disc

The Blu-ray disc player is located in the center console.

1. Insert a Blu-ray disc into the VES disc player with the

label facing as indicated on the Blu-ray player. The radio
automatically selects the appropriate mode after the disc
is recognized and displays the menu screen, the lan-
guage screen, or starts playing the first track.

2. To watch a Blu-ray disc on Rear 1 for driver’s side rear

passengers, ensure the Remote Control and Headphone
switch is on Rear 1.

3. To watch a Blu-ray disc on Rear 2 for passenger side rear

passengers, ensure the Remote Control and Headphone
switch is on Rear 2.

Blu-ray Disc Player Location

10

MULTIMEDIA

517

NOTE:
• To view a Blu-ray disc on the radio, press the “Media”

button on the touchscreen, and then press the “Disc”
button. Press the “Play” button, and then the “full
screen” button.

• Viewing a Blu-ray disc on the radio screen is not

available in all states/provinces. The vehicle must be
stopped, and the gear selector must be in the PARK
position for vehicles with automatic transmission.

Using The Touchscreen Radio

1. RSE Channel 1 Mode

Indicates the current source for Screen 1/Channel 1. This
button will be highlighted when it is the active Screen/
Channel being controlled by the front user. If this button is
not highlighted, select button to access controls for Screen
1/Channel 1 source.

2. RSE Power

Press to turn RSE On/Off.

3. RSE Mute

Mute rear headphones for the current ignition cycle. Press-
ing mute again will unmute rear headphones.

4. RSE Remote Control Lock Out

Press to enable/disable remote control functions.

5. RSE Channel 2 Mode

Indicates the current source for Screen 2/Channel 2. This
button will be highlighted when it is the active Screen/
Channel being controlled by the front user. If this button is
not highlighted, select button to access controls for Screen
2/Channel 2 source.

Rear Media Control Screen

518

MULTIMEDIA

6. Cabin Audio Mode

Select this button to change the cabin audio to the rear
entertainment source currently shown on the rear media
control screen.

7. Radio Full Screen Mode

Select this button to change to Full Screen Mode.

8. RSE Mode

Select this button to change source for the active (high-
lighted) rear Screen/Channel on the rear media control
screen.
• Press the Media button on the touchscreen, and then

press the rear media button on the touchscreen.

• Press the OK button on the touchscreen to begin playing

the Blu-ray disc on the touchscreen radio.

Using The Remote Control
• Select an audio channel (Rear 1 for driver’s side rear

screen and Rear 2 for passenger’s side rear screen), and
then press the source key, and using the up and down
arrows, highlight disc from the menu and press the OK
button.

• Press the popup/menu key to navigate the disc menu

and options.

Play Video Games

Connect the video game console to the Audio/Video
RCA/HDMI input jacks located on the side of each seat.

Audio/Video RCA/HDMI Jacks (AUX/HDMI Jacks) on
the side of each seat enable the monitor to display video
directly from a video camera, connect video games for
display on the screen, or play music directly from an MP3
player.

Audio/Video RCA/HDMI Input Jacks

10

MULTIMEDIA

519

When connecting an external source to the AUX/HDMI
input, ensure to follow the standard color coding for the
audio/video jacks:

1. HDMI Input.

2. Right audio in (red).

3. Left audio in (white).

4. Video in (yellow).

NOTE:

Certain high-end video games consoles may exceed

the power limit of the vehicle’s Power Inverter.

Play A DVD/Blu-ray Disc Using The Touchscreen
Radio

1. Insert the DVD/Blu-ray Disc with the label facing as

indicated on the DVD/Blu-ray Disc player. The radio
automatically selects the appropriate mode after the disc
is recognized and displays the menu screen or starts
playing the first track.

2. To watch a DVD/Blu-ray Disc on Rear 1 (driver’s side

rear passenger), ensure the Remote Control and Head-
phone channel selector switch is on Rear 1.

3. To watch a DVD/Blu-ray Disc on Rear 2 (passenger’s

side rear passenger), ensure the Remote Control and
Headphone channel selector switch is on Rear 2.

Using The Remote Control

1. Push the SOURCE button on the Remote Control.

2. While looking at Rear 1 or 2, highlight DISC by either

pushing Up/Down/Left/Right buttons, then push
ENTER/OK.

Select DISC Mode On The Rear Seat Entertainment Screen

520

MULTIMEDIA

Using The Touchscreen Radio Controls

1. Press the Media button on the Uconnect system touch-

screen.

2. Press the Rear Media button to display the Rear Media

Control screen.

3. Press the 1 or 2 buttons on the touchscreen, and the

select source button on the touchscreen. Press the DISC
button on the touchscreen in the MEDIA column. To
exit, press the X at the top right of the screen.

NOTE:

Pressing the screen on the radio while a DVD or

Blu-ray Disc is playing, brings up the basic remote control
functions for DVD play such as scene selection, Play, Pause,
FF, RW, and Stop. Pressing the X in the upper corner will
turn OFF the remote control screen functions.

Important Notes For Dual Video Screen System
• The Rear Seat Entertainment System is able to transmit

two channels of stereo audio and video simultaneously.

• The Blu-ray Disc Player can play CDs, DVDs and

Blu-ray Discs.

Rear Media Control Screen

Rear Seat Entertainment Source Screen

10

MULTIMEDIA

521

• Selecting a video source on Rear 1, the video source will

display on Rear 1 and can be heard on Rear 1.

• Selecting a video source on Rear 2, the video source will

display on Rear 2 and can be heard on Rear 2.

• Audio can be heard through the headphones even when

the screen(s) are closed.

Blu-ray Disc Player Remote Control — If Equipped

Controls And Indicators

1. Power — Turns the screen and wireless headphone

transmitter for the selected Channel on or off. To hear
audio while the screen is closed, push the Power button
to turn the headphone transmitter on.

2. Channel Selector Indicators — When a button is pushed,

the currently affected channel or channel button is
illuminated momentarily.

3. SOURCE — Push to enter Source Selection screen.

4. Channel/Screen Selector Switch — Indicates which

channel is being controlled by the remote control. When
the selector switch is in the Rear 1 position, the remote
controls the functionality of headphone Channel 1 (left
screen). When the selector switch is in the Rear 2
position, the remote controls the functionality of head-
phone Channel 2 (right screen).

5.

䉴 — Push to navigate menus.

6. SETUP — Push to access the screen settings menu.

7.

䉴䉴 — Push and hold to fast forward through the
current audio track or video chapter.

8.

䉴 / 㥋 (Play/Pause) — Begin/resume or pause disc play.

Blu-ray Player Remote Control

522

MULTIMEDIA

9. Four Colored Buttons — Push to access Blu-ray Disc

features.

10. POPUP/MENU — Push to bring up repeat and shuffle

options, the Blu-ray Disc popup menu, the DVD title
menu, or to access disc menus.

11. Keypad — Push to navigate chapters or titles.

12.

(Stop) — Stops disc play.

13.

䉳䉳 — Push and hold to fast rewind through the

current audio track or video chapter.

14.

— Mutes headphone audio.

15. BACK — Push to exit out of menus or return to source

selection screen.

16.

䉲 — Push to navigate menus.

17.

䉳 — Push to navigate menus.

18. OK— Push to select the highlighted option in a menu.

19.

䉱 — Push to navigate menus.

Headphones Operation

The headphones receive two separate channels of audio
using an infrared transmitter from the video screen.

If no audio is heard after increasing the volume control,
verify that the screen is turned on, the channel is not muted
and the headphone channel selector switch is on the
desired channel. If audio is still not heard, check that fully
charged batteries are installed in the headphones.

Rear Seat Entertainment Headphones

1 — Power Button
2 — Volume Control
3 — Channel Selection Switch

10

MULTIMEDIA

523

Controls

The headphone power indicator and controls are located
on the right ear cup.

NOTE:

The rear video system must be turned on before

sound can be heard from the headphones. To conserve
battery life, the headphones will automatically turn off
approximately three minutes after the rear video system is
turned off.

Changing the Audio Mode for Headphones

1. Ensure the Remote Control channel/screen selector

switch is in the same position as the headphone selector
switch.

NOTE:

• When both the headphone and the remote control

channel selector switches are on Channel 1, the Re-
mote is controlling Channel 1 and the headphones are
tuned to the audio on Channel 1.

• When both the headphone and the remote control

channel selector switches are on Channel 2, the Re-
mote is controlling Channel 2 and the headphones are
tuned to the audio on Channel 2.

2. Push the SOURCE button on the remote control.

3. Pushing the SOURCE button will advance to the next

mode.

4. When the Mode Selection menu appears on screen, use

the cursor buttons on the remote control to navigate to
the available modes and push the OK button to select
the new mode.

5. To cancel out of the Mode Selection menu, push the

BACK button on the remote control.

Replacing The Headphone Batteries

Each set of headphones requires two AAA batteries for
operation. To replace the batteries:

1. Locate the battery compartment on the left ear cup of

the headphones, and then slide the battery cover down-
ward.

2. Replace the batteries, making sure to orient them ac-

cording to the polarity diagram shown.

3. Replace the battery compartment cover.

524

MULTIMEDIA