Toyota FJ Cruiser (GSJ 10, 15 series). Manual — part 339
MI–12
MIRROR – OUTER REAR VIEW MIRROR
MI
(b) Install the outer rear view mirror with the 3 bolts.
Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf)
(c) Connect the connector.
3.
INSTALL NO. 2 FRONT DOOR SERVICE HOLE
COVER
HINT:
Use the same procedure as for the RH side (see page
4.
INSTALL FRONT DOOR TRIM BOARD SUB-
ASSEMBLY
HINT:
Use the same procedure as for the RH side (see page
5.
INSTALL FRONT ARMREST BASE UPPER PANEL
(See page
)
6.
CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
Torque: 3.9 N*m (40 kgf*cm, 35 in.*lbf)
B135564
MIRROR – OUTER MIRROR SWITCH
MI–13
MI
BODY
MIRROR
OUTER MIRROR SWITCH
COMPONENTS
FUSE BOX OPENING
COVER
OUTER MIRROR
SWITCH
B138152E01
MI–14
MIRROR – OUTER MIRROR SWITCH
MI
REMOVAL
1.
DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
2.
REMOVE FUSE BOX OPENING COVER
(a) Disengage the 4 claws and remove the fuse box
opening cover.
3.
REMOVE OUTER MIRROR SWITCH
(a) Using a screwdriver with its tip wrapped in
protective tape, disengage the 2 claws and remove
the outer mirror switch.
(b) Disconnect the connector.
INSPECTION
1.
INSPECT OUTER MIRROR SWITCH
(a) Check the resistance.
(1) Select L on the left/right adjustment switch.
(2) Using an ohmmeter, measure the resistance
and check the results in accordance with the
value(s) in the table below.
Standard Resistance
If the result is not as specified, replace the
outer mirror switch.
(3) Select R on the left/right adjustment switch.
B138155
Protective Tape
B138153E01
L R
MIRROR
1
2
3
4
5
6
7
8
9
10
B127217
Tester Connection
Condition
Specified Condition
4 (VL) - 7 (E)
4 (VL) - 8 (B)
5 (HL) - 7 (E)
5 (HL) - 8 (B)
6 (M+) - 7 (E)
6 (M+) - 8 (B)
OFF
10 k
Ω or higher
4 (VL) - 8 (B)
6 (M+) - 7 (E)
UP
Below 1
Ω
4 (VL) - 7 (E)
6 (M+) - 8 (B)
DOWN
Below 1
Ω
5 (HL) - 8 (B)
6 (M+) - 7 (E)
LEFT
Below 1
Ω
5 (HL) - 7 (E)
6 (M+) - 8 (B)
RIGHT
Below 1
Ω
MIRROR – OUTER MIRROR SWITCH
MI–15
MI
(4) Using an ohmmeter, measure the resistance
and check the results in accordance with the
value(s) in the table below.
Standard Resistance
If the result is not as specified, replace the
outer mirror switch.
INSTALLATION
1.
INSTALL OUTER MIRROR SWITCH
(a) Connect the connector.
(b) Engage the 2 claws and install the outer mirror
switch.
2.
INSTALL FUSE BOX OPENING COVER
(a) Engage the 4 claws and install the fuse box opening
cover.
3.
CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
Torque: 3.9 N*m (40 kgf*cm, 35 in.*lbf)
Tester Connection
Condition
Specified Condition
2 (HR) - 7 (E)
4 (HR) - 8 (B)
3 (VR) - 7 (E)
3 (VR) - 8 (B)
6 (M+) - 7 (E)
6 (M+) - 8 (B)
OFF
10 k
Ω or higher
3 (VR) - 8 (B)
6 (M+) - 7 (E)
UP
Below 1
Ω
3 (VR) - 7 (E)
6 (M+) - 8 (B)
DOWN
Below 1
Ω
2 (HR) - 8 (B)
6 (M+) - 7 (E)
LEFT
Below 1
Ω
2 (HR) - 7 (E)
6 (M+) - 8 (B)
RIGHT
Below 1
Ω
B138154
B138155
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст