Toyota FJ Cruiser (GSJ 10, 15 series). Manual — part 338

MI–8

MIRROR – OUTER REAR VIEW MIRROR

MI

REMOVAL

HINT:
•

Use the same procedure for both the RH and LH sides.

•

The procedure described below is for the LH side.

1.

DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL

2.

REMOVE FRONT ARMREST BASE UPPER PANEL
(See page

WS-25

)

3.

REMOVE FRONT DOOR TRIM BOARD SUB-
ASSEMBLY
HINT:
Use the same procedure as for the RH side (see page

ED-9

).

4.

REMOVE NO. 2 FRONT DOOR SERVICE HOLE
COVER
HINT:
Use the same procedure as for the RH side (see page

ED-10

).

5.

REMOVE OUTER REAR VIEW MIRROR
(a) Driver side:

Provisionally install the power window regulator
master switch.

(b) Passenger side:

Provisionally install the power window regulator
switch.

(c) Close the door glass.
(d) Disconnect the connector.
(e) Remove the 3 bolts and the outer rear view mirror.

NOTICE:
Do not drop or damage the outer rear view
mirror when removing the bolts.

(f)

Apply protective tape to the lower part of the mirror
body.

(g) Press down the upper part of the mirror and tilt the

mirror.

B135564

Protective
Tape

B140036E01

MIRROR – OUTER REAR VIEW MIRROR

MI–9

MI

(h) Using a screwdriver with its tip wrapped in

protective tape, insert it between the mirror holder
and the mirror holder base.

(i)

Twist and disengage the 2 clips on the lower side of
the mirror.
HINT:
Heating the mirror holder with a domestic dryer
before this procedure makes the work easier.

(j)

While holding the mirror with the screwdriver,
disengage the 4 clips and 2 claws on the upper side
of the mirror and remove the mirror.

(k) Driver side:

Remove the power window regulator master switch.

(l)

Passenger side:
Remove the power window regulator switch.

6.

REMOVE OUTER REAR VIEW MIRROR
ILLUMINATION LIGHT BULB (w/ Illumination)
(a) Turn the outer rear view mirror illumination light

socket and bulb, in the direction indicated by the
allow in the illustration, to remove them.

(b) Remove the outer rear view mirror illumination light

bulb from the light socket.

Mirror Holder

Mirror Holder
Base

B140035E01

Protective Tape

B138150E01

E127190

MI–10

MIRROR – OUTER REAR VIEW MIRROR

MI

INSPECTION

1.

INSPECT OUTER REAR VIEW MIRROR ASSEMBLY
LH
(a) Check the operation.

(1) Apply battery voltage to the outer rear view

mirror and check the operation of the outer rear
view mirror.
Standard

If the result is not as specified, replace the
outer rear view mirror.

2.

INSPECT OUTER REAR VIEW MIRROR ASSEMBLY
RH
(a) Check the operation.

(1) Apply battery voltage to the outer rear view

mirror and check the operation of the outer rear
view mirror.
Standard

If the result is not as specified, replace the
outer rear view mirror.

3.

INSPECT OUTER REAR VIEW MIRROR
ILLUMINATION LIGHT
(a) Check the illumination operation.

(1) Connect the positive (+) battery lead to terminal

2 and the negative (-) battery lead to terminal 1,
then check that the illumination illuminates.
Standard:

Illumination illuminates.

If the illumination does not illuminate, check the
faulty bulb.

1

2

3

4

5

B135566

Measurement Condition

Mirror Assembly Operation

Battery positive (+) - Terminal 3 (MV)

Battery negative (-) - Terminal 4 (COM)

Turns upward

Battery positive (+) - Terminal 4 (COM)

Battery negative (-) - Terminal 3 (MV)

Turns downward

Battery positive (+) - Terminal 5 (MH)

Battery negative (-) - Terminal 4 (COM)

Turns left

Battery positive (+) - Terminal 4 (COM)

Battery negative (-) - Terminal 5 (MH)

Turns right

1

2

3

4

5

B135567

Measurement Condition

Mirror Assembly Operation

Battery positive (+) - Terminal 3 (MV)

Battery negative (-) - Terminal 4 (COM)

Turns upward

Battery positive (+) - Terminal 4 (COM)

Battery negative (-) - Terminal 3 (MV)

Turns downward

Battery positive (+) - Terminal 5 (MH)

Battery negative (-) - Terminal 4 (COM)

Turns left

Battery positive (+) - Terminal 4 (COM)

Battery negative (-) - Terminal 5 (MH)

Turns right

1

2

3

4

5

B140027

MIRROR – OUTER REAR VIEW MIRROR

MI–11

MI

(b) Inspect the bulb.

(1) Inspect continuity of the bulb by connecting the

tester.
Standard:

Continuity.

If continuity exists, replace the outer rear view
mirror.
If no continuity exists, replace the bulb.

INSTALLATION

1.

INSTALL OUTER REAR VIEW MIRROR
ILLUMINATION LIGHT BULB (w/ Illumination)
(a) Install the outer rear view mirror illumination light

bulb into the light socket.

(b) Turn the outer rear view mirror illumination light

socket and bulb, in the direction indicated by the
arrow in the illustration, to install them.

2.

INSTALL OUTER REAR VIEW MIRROR
(a) Engage the 2 claws on the upper side of the mirror

and the 6 clips and install the mirror.
HINT:
Heating the mirror holder with a domestic dryer
before this procedure makes the work easier.

E127191

B138151