Citroen C2 (2008 year). Manual — part 5
1
5
3
2
4
III
81
F R O N T S E A T S
1
5
4
3
2
III
82
F R O N T S E A T S
Manual adjustments
Head restraint
To raise or lower the head restraint, pull it forwards at the same
time as sliding it.
The adjustment is correct when the top edge of the head
restraint is at the same height as the top of the head.
To remove it, bring it to the high position. Lift the tab with the aid of a coin
and pull.
Backrest angle
Action the control rearwards and adjust the angle of the
backrest.
It is possible to recline the backrest to an angle of 45° by
tilting it until it locks. Press the control to unlock.
Seat height and rake adjustment
Lift the control and use the weight of your body to move the
seat to the desired position.
Reach
Lift the control bar and adjust to the desired position.
Access to the rear seat positions
To access the rear seat positions, action the control forwards
to fold the backrest and slide the front seat.
Afterwards the front seat will revert to its initial position.
Make sure that the seat is secured in place (particularly if the
rear seats are folded).
Heated seats
The front seats can be heated indi-
vidually. Use the controls located
at the side of the seats, and select
one of the three heating levels:
0: Off.
1: Slight heat.
2: Medium heat.
3: Maximum heat.
The seat temperature adjusts auto-
matically.
Note: The heated seats only oper-
ate when the engine is running.
1
2
3
4
III
83
R E A R S E A T S
For ease of handling from the boot, it is advised to close the lower tailgate.
1
4
3
2
III
84
R E A R S E A T S
The function 3 is available on all models. The other functions are available depending on the version of your vehicle.
Fore and aft adjustment
From the boot, it is possible to modify the loadspace by sliding the seats.
Push down control 2 and adjust to the desired position.
At the front of the seat, it is also possible to adjust knee room.
Raise the bar located under the seat and adjust to the desired position (several positions).
Rear head restraints
The rear head restraints have two positions:
A stowed position for when the seat is not occupied.
A deployed position to provide passenger safety, by raising them to their locking point.
To raise them, pull them upwards to their maximum height, pressing the unlocking button.
•
•
Foldable backrest
It can be folded either totally or partially.
Lower the head restraint against the backrest, then pivot control 3 towards the rear of the vehicle.
The backrest also has a vertical position to optimise the bootspace.
When you reposition the backrest, make sure that it locks in place.
Folded (fully-folded position)
To facilitate this manoeuvre, slide the front seat as far forward as possible, using the fore/aft slide
control.
Move the rear seat as far forward as possible using control 2, fold the backrest using control 3, then
lift control 4.
The seat goes automatically to the fully-folded position.
Reposition the front seat. The rear seat in the fully-folded position will adapt automatically to the position of the front
seat.
When restoring the seat to its original position, check that there is nothing obstructing the anchoring points to ensure
that it latches properly.
III
85
S E A T C O N F I G U R A T I O N
TRANSPORTING LONG OBJECTS
Rear seats
By confi guring the rear seats, you can create space for a variety of objects.
As a safety measure, use the anchoring rings positioned on the boot fl oor.
4-seater
versions
Versions with folding
backrests
Versions with
fully-folding seats
A
III
86
A I R B A G S
In the front passenger's seat position, it is imperative to deactivate the
front passenger's airbag if you are installing a "rear-facing" child seat
there. Otherwise the child risks being killed or seriously injured should
the airbag deploy.
Front passenger's airbag deactivation
In order to be able to use a rear-facing child seat in the front passenger's seat position, it is imperative to deactivate
the passenger's airbag.
For that:
With the ignition switched off, insert the key into the switch A.
Turn the key to the
"OFF" position, the passenger's airbag is deactivated.
The front passenger's airbag deactivation warning lamp, in the instrument panel, lights up when you switch on
the ignition.
Reactivating the front passenger's airbag
Do not forget to reactivate the function.
For that:
With the ignition switched off, insert the key into the switch A.
Turn the key to the
"ON" position, the airbag is activated.
The warning lamp in the instrument panel lights up for a few seconds when you switch on the ignition.
The airbags only function with the ignition switched on. A slight noise is emitted when they are triggered.
Note: the gas released from the airbags may be a mild irritant.
•
•
•
•
•
•
III
87
C H I L D R E S T R A I N T S
ISOFIX anchoring points and
the ISOFIX fastening system
The rear seats of your vehicle are
equipped with ISOFIX anchoring
points. These consist of 2 rings
located between the backrest and
the vehicle seat, approx. 28 cm
apart.
ISOFIX child seats are equipped
with 2 latches which are eay to
attach to these rings. This fi xing
system is intended for children
weighing up to 18 kg.
Incorrect installation of a child seat
in a vehicle compromises protection
of the child in the event of a collision.
The ISOFIX system enables you to
minimise the risks posed by incorrect
fi tting. The ISOFIX fastening system
gives you a convenient, strong and
reliable fi tting for a child seat in your
vehicle.
The recommended ISOFIX child seat (1) for your vehicle is:
The ISOFIX RÖMER Duo Plus (1):
This child seat has been approved for children between 9 – 18 kg. It can
only be installed in the "forward-facing" position. The front seat must be
adjusted so that the child’s feet are not touching the backrest of the front
seat (slide the rear seat back as far as possible). The use of a top belt is not
necessary.
This child seat can also be installed in seat positions not fi tted with ISOFIX
anchoring points. In this case, it must be secured to the seat by means of
the vehicle seat belt.
(1): On the ISOFIX anchoring points of the vehicle, you can only attach the
ISOFIX child seat approved for this vehicle.
III
88
C H I L D R E S T R A I N T S
Child seats secured by
means of the vehicle seat
belt
In conformity with Directive 2003/20,
the table tells you to what extent
each of the seat positions in your
vehicle may take a child seat
that is secured by means of the
vehicle seat belt and approved
as "Universal" as a function of the
weight of the child.
Consult
"User
Precautions",
chapter on "Child Safety" at the
end of this handbook, in order
to ensure that you are installing
your child in conditions of maxi-
mum safety.
Seat position(s)
Weight of child
Up to 10 kg
and up to 13 kg
Up to 10 kg
Up to 10 kg
(groups 0 and 0+)
and up to 13 kg
and up to 13 kg
9 - 18 kg
(group 1)
9 - 18 kg
9 - 18 kg
15 - 25 kg
(group 2)
15 - 25 kg
15 - 25 kg
22 - 36 kg
(group 3)
22 - 36 kg
22 - 36 kg
Front
passenger’s (a)
Fixed seat
U
U
U
U
Height-
adjustable seat
U (R)
U (R)
U (R)
U (R)
Rear passenger’s seat
U
U
U
U
KEY TO THE TABLE
U: Seat position suitable for the installation of a universal rear-facing child seat and a universal forward-facing child seat
position.
U(R): Seat position suitable for installation of a universal rear-facing child seat and of a forward-facing seat. The vehicle seat
should be adjusted to the highest position.
(a): In the front passenger's seat position, it is imperative to deactivate the front passenger's airbag if you are installing a "rear-
facing" child seat there. Otherwise the child risks being killed or seriously injured should the airbag deploy. Before placing
your child in the front passenger’s seat position, consult the legislation currently in force in your country on the carrying of
children in this position.
Take care to comply with the fi tting instructions given in the
child seat manufacturer’s installation guide.
1
2
2
III
89
I N T E R I O R L I G H T I N G
1. Interior lamps
Move the control 1 to the 3 following positions.
Automatic lighting of the interior lamps
On entering the vehicle:
They come on as soon as the vehicle is unlocked or a door is opened.
They go out 30 seconds after the doors are closed or when ignition is switched on.
On vacating the vehicle:
They come on as soon as the ignition key is removed (timed for 30 seconds), or when a door is opened.
They go out 30 seconds after all the doors have been closed or immediately after the vehicle has been locked.
2. Spotlamps
A press on one of the buttons 2 switches the corresponding spotlamp on or off.
These do not work if the ignition is off or in economy mode.
•
•
In this position, the interior lamp comes on when you open a door
or the boot.
In this position, it is deactivated and remains permanently off. The
spotlamps are deactivated.
In this position, lighting is permanent.
III
90
I N T E R I O R C O M F O R T
Lower glovebox
To open, pull the handle and lower
the lid.
It comprises a storage area for
vehicle documents.
The glove box permits access to
the fascia fuse box
.
Storage/CD changer
Oddments tray on front
central console
WARNING
As a safety measure, the glovebox must remain shut
when the vehicle is in motion.
III
91
I N T E R I O R C O M F O R T
Cigar-lighter
Functions when the ignition is
switched on.
Push in and wait a few moments.
The cigar lighter will release auto-
matically.
Ashtray
A movable ashtray can be placed
in the cupholder locations on the
central console and in the storage
pockets of the rear panels.
Storage pockets in the front
doors
Storage pockets in the rear
panels
III
92
I N T E R I O R C O M F O R T
Sun visor
To prevent dazzle from ahead, fold
the visor downwards. They can
be disengaged from their central
fi xing and pivoted over to the side
windows if required.
The passenger’s and driver’s sun
visors each have a mirror that can
be covered.
Sun visor with illuminated
mirror
Illuminates automatically on opening
the mirror cover fl ap (ignition on).
Storage areas
Straps fi xed to the bottom of the
boot enable you to secure objects
stowed there.
Grab handles/Coat hanger
hook
The lower tailgate can
support spread loads of
up to 100 kg.
Lower tailgate storage
Lift up the two levers located on
the lower tailgate to open the cover
and access the storage area.
Storage capacity: 5 litres.
1
2
3
III
93
R E A R P A R C E L S H E L F
Removal
Open the upper tailgate.
Detach the parcel shelf cords.
Pull fi rmly downwards to
disengage the hinge pivots.
•
•
•
Refi tting
Open the upper tailgate.
orient the underside of the shelf towards you.
introduce the two hinge pivots into the apertures located on the upper
tailgate trim.
attach the cords (on the right hand side: take care to pass the cord to
the outside of the upper tailgate strut, positioning the ball 1 of the cord
between the boot attachment 2 and the tailgate hinge 3).
•
•
•
•
Do not place any hard or heavy item on the shelf.
These could be dangerous if thrown around during harsh braking or, if
they touch the rear screen, could damage the heating elements.
A
IV
94
Check that the bonnet is properly secured.
Avoid opening the bonnet in high winds.
Bonnet
This operation should only be
performed while the vehicle is
stationary.
To release the bonnet, pull the con-
trol located under the dashboard
towards you.
Operate the lever A, located above
the grille, to the right of the chev-
rons, then lift.
Note: The panel may be hot after
the vehicle has been in use.
Bonnet stay: Unclip the stay and
pivot to lodge it in the notch.
To close
Return the bonnet stay to its initial
position.
Check that nothing has been left
on top of the engine and that any
component that was moved has
been correctly repositioned.
Lower the bonnet carefully, then let
it drop shut.
B O N N E T R E L E A S E
A
B
IV
95
L E V E L S
REFER TO THE CHAPTER: USER PRECAUTIONS
Air fi lter
Follow the requirements
set out in the Maintenance
Guide.
Windscreen/rear
screen wash and
headlamp wash fl uid
Use CITROËN-approved
products wherever possible.
Capacity: See "Capacities".
Characteristics of fl uid
In order to ensure optimum cleaning
and to avoid freezing, you must
never top up or replace this fl uid
with water.
Engine coolant
The fl uid level should be
between the marks MIN. and
MAX. on the header tank.
Engine hot, wait at least 15 minutes.
Quality: See "Maintenance Guide".
Never do anything relating to
the cooling system of an engine
that is hot.
12 V battery
See "Starting with a slave
battery".
Engine oil
Check the engine oil level
on horizontal ground with
the engine having been
switched off for at least 10 minutes.
Quality: See "Maintenance Guide".
Pull out the manual dipstick.
The
level
should
be
between the marks MIN.
and MAX. on the gauge.
It must never exceed the
maximum.
MAX.
MIN.
Brake fl uid
The level of fl uid should be
between the marks MIN.
and MAX. on the reservoir.
Quality: See "Maintenance Guide".
If the warning lamp comes on
while you are driving, stop
immediately
and
contact
a
CITROËN dealer.
immediately
and
immediately
Cabin particle fi lter/
Odour fi lter
See "Maintenance Guide".
If opening the bonnet when the engine is hot, even if it is
stopped and the ignition is switched off, remember that the
cooling fan may operate at any moment.
Consult "User Precautions" at the end of this handbook.
IV
101
L E V E L S
Engine oil
Check the engine oil level on
horizontal ground with the engine
having been switched off for at
least 10 minutes.
Pull out the manual dipstick.
The level should be between the
marks MIN. and MAX. on the
gauge.
Topping up engine oil
Before fi lling, pull out the dipstick.
Check the dipstick after fi lling.
It must never exceed the maxi-
mum.
Screw the cap back on and close
the bonnet.
Quality: See the Maintenance
Guide.
If opening the bonnet when the engine is hot, even if it is
stopped and the ignition is switched off, remember that the
cooling fan may operate at any moment.
Radiator – coolant fl uid
Checking the level and topping up
with fl uid must always be done with
the engine cold.
Engine hot
Release the protection cover.
Wait 15 minutes or for the tem-
perature to be lower than 100 °C
and then carefully unscrew the
cap so as to allow the pressure to
drop, protecting yourself with, say,
a cloth.
Topping up the coolant
The fl uid level should be between
the marks MIN. and MAX. on the
header tank.
Top up the level. If you have to
put in more than 1 litre, have the
cooling system checked by a
CITROËN dealer.
cooling system checked
cooling system
Make sure that the cap is
back on properly.
Note:
If you need to top up the fl uid
frequently, this indicates a malfunc-
tion which you should get checked
at the earliest opportunity.
Quality: See the Maintenance
Guide.
Remark: The cooling fan may
operate for around 10 minutes
after the engine has stopped.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст