Citroen C2 (2008 year). Manual — part 6
IV
96
1 . 1 i E N G I N E
1 . 4 i E N G I N E
IV
97
1 . 6 i 1 6 V 1 1 0 h p E N G I N E
IV
98
1 . 6 i 1 6 V 1 2 5 h p E N G I N E
IV
99
H D i 7 0 E N G I N E
The diesel fuel circuit being
under high pressure:
ANY INTERVENTION ON THE
CIRCUIT IS PROHIBITED.
H D i e n g i n e s a r e t h e r e s u l t o f a d v a n c e d
technology.
Any intervention requires special qualifi cations
which only a CITROËN dealer can guarantee.
Any intervention requires special qualifi cations
Any intervention requires special qualifi cations
IV
100
1 . 6 H D i 1 1 0 h p E N G I N E
H D i e n g i n e s a r e t h e r e s u l t o f a d v a n c e d
technology.
Any intervention requires special qualifi cations
which only a CITROËN dealer can guarantee.
Any intervention requires special qualifi cations
Any intervention requires special qualifi cations
IV
102
HDi 70 engine
1.6 HDi engine
HDi engines are the result of advanced technology.
Any intervention requires special qualifi cations which only a
CITROËN dealer can guarantee.
Any intervention requires special qualifi cations which only a
Any intervention requires special qualifi cations which only a
D I E S E L I N J E C T I O N E Q U I P M E N T
Draining water from the fuel
fi lter
Purge regularly (at each oil change).
To drain the water, slacken the
bleed screw or the water-in-diesel-
fuel sensor located at the base of
the fi lter.
Operate until the water has com-
pletely drained away.
Then retighten the bleed screw or
the water in diesel fuel sensor.
IV
103
HDi 70 engine
1.6 HDi engine
Detach the protection cover to
access the priming pump.
HDi engines are the result of advanced technology.
Any intervention requires special qualifi cations which only a
CITROËN dealer can guarantee.
Any intervention requires special qualifi cations which only a
Any intervention requires special qualifi cations which only a
D I E S E L I N J E C T I O N E Q U I P M E N T
Priming the fuel system
In the event of running out of fuel:
After fi lling (5 litres minimum),
operate the manual priming
pump until some resistance is
felt.
Operate the starter motor while
depressing the accelerator
pedal slightly until the engine
starts.
If the engine fails to start at the fi rst
attempt, wait 15 seconds before
trying again.
If the engine fails to start after sev-
eral attempts, repeat the procedure
from the beginning.
When the engine is idling, accelerate
slightly to complete the bleeding of
the circuit.
•
•
IV
104
C A P A C I T I E S
Engine type
Engine oil capacities (in litres)
(1)
1.1i engine
3.2
1.4i engine
3.2
1.6i 16V 110 ch engine
3.2
1.6i 16V 125 ch engine
3.2
HDi 70 engine
3.8
1.6 HDi 110 ch engine
3.75
(1)
Drain, refi ll and replace oil fi lter.
Screen wash fl uid (in litres)
3.5
Screen and headlamp wash fl uid
(in litres)
6
IV
105
Starting the engine after disconnecting and reconnecting
the battery
Turn the ignition key.
Wait approximately 1 minute before operating the starter in order to
allow the electronic systems to re-initialise. It may be necessary to
enter the radio code.
•
•
After the battery has been disconnected for a lengthy period of time, it may be necessary to re-initialise the following
functions:
Anti-pinch and sequential operation on the electric windows.
The multifunction display parameters (date, time, language, units of distance and of temperature).
The Radio stations.
Electronic Gearbox System: See Electronic Gearbox System (REINITIALISATION).
•
•
•
•
1 2 V B A T T E R Y
A
B
IV
106
Starting the engine with an assisting battery
If the battery is discharged, it is possible to use either a separate
emergency battery or a battery on another vehicle.
A. Dischargedbattery (Under the bonnet).
B. Assisting battery.
Check that the assisting battery has suffi cient voltage (12 V).
If you use the battery on another vehicle, stop the engine on the
latter. The two vehicles must not come into direct contact with
each other.
Connect the cables according to the order indicated in the
order
diagram. Check that the leads are well secured (risk of sparks).
Start the engine of the assisting vehicle. Let the engine run for
around 1 minute at a slightly accelerated idle.
Operate the starter on the vehicle being assisted.
It is essential to follow the indicated sequence correctly.
Never approach with a fl ame or create sparks in the vicinity
of the battery (explosive gas).
The battery contains dilute sulphuric acid which is highly
corrosive.
When handling batteries, always protect your face and
especially your eyes.
In the event of any contact with the skin, rinse immediately
with copious amounts of fresh water.
Advice
Do not touch the leads during
the operation.
Do not lean over the batteries.
Disconnect the cables in reverse
order, making sure they do not
touch together.
1 2 V B A T T E R Y
IV
107
F U S E S
Fuseboxes
There are two fuse boxes, one below the dashboard and one under the
bonnet.
Dashboard fuses
The fuse box is located in the lower glovebox compartment.
To access the fuses, open the glove box, pull the handle on the fuse box
cover.
Replacing a fuse
Before replacing a fuse, you should ascertain the cause of the fault and
have it remedied. The numbers of the fuses are indicated on the fusebox.
Good
Bad
Pliers A
Replace the fuse that has blown with one of the same rating (same
colour).
Use the special pliers A stowed on the cover close to the fuseboxes, this
includes a compartment for replacement fuses.
IV
108
T A B L E O F F U S E S
D A S H B O A R D F U S E S
Ref.
Rating
Function
3
5 A
Airbags
4
10 A
Diagnostic socket – Particle fi lter additive – Clutch switch – Steering angle sensor
5
30 A
–
6
30 A
Screen wash
8
20 A
Digital clock – Controls at the steering wheel – Radio – Display
9
30 A
Cigar-lighter – Digital clock – Interior lamps – Vanity mirror
10
15 A
Alarm
11
15 A
Ignition switch – Diagnostic socket
12
15 A
Airbag ECU – Rain and brightness sensor
14
15 A
Parking assistance – Instrument panel – Air conditioning – Bluetooth
®
telephone
®
15
30 A
Central locking – Deadlocking
17
40 A
Demisting - deicing of the rear screen
18
SHUNT
CUSTOMER PARK SHUNT
IV
109
F U S E S
Any action on the MAXI fuses (that give extra protection) (in
grey in the diagrams), located in the fuseboxes, should be left
to a CITROËN dealer.
grey in the diagrams), l
the dia
Fusebox
To access the fusebox located in
the engine compartment, remove
the battery cover and detach the
lid.
After a repair, take care to
reclose the cover.
Fuses under the bonnet
IV
110
T A B L E O F F U S E S
F U S E S U N D E R T H E B O N N E T
Ref.
Rating
Function
1
20 A
Water-in-diesel-fuel sensor
2
15 A
Horn
3
10 A
Screen wash
4
20 A
Headlamp wash
5
15 A
Fuel pump
6
10 A
Power steering
7
10 A
Coolant level sensor
8
25 A
Starter
9
10 A
ECUs (ABS, ESP)
10
30 A
Engine control actuators (Ignition coil, Electrovalve, Oxygen sensor, Injection) – Canister purge
11
40 A
Air blower
12
30 A
Windscreen wiper
14
30 A
Air pump (petrol version) – Diesel fuel heater
V
111
R E F U E L L I N G
To open the fl ap, pull at the edge.
Locking fi ller cap
Turn the key a quarter turn to lock
and unlock the fi ller cap.
When refuelling, place the cap in
the support provided on the inside
of the fi ller fl ap.
For a petrol engine with a cata-
lytic converter, unleaded fuel is
compulsory.
The fi ller neck is narrower to
ensure that only unleaded petrol
can be put in.
When you are seeking to fi ll your tank, do not persist after the third
cut-off ; that could cause your vehicle to malfunction.
Fuel tank capacity (in litres): Approx. 41.
If you should put in fuel that is not suitable for your vehicle's
engine type, it is imperative to have the tank drained before
you start the engine again.
FUEL QUALITY
A label inside the fi ller fl ap tells you which type of fuel to use.
UNLEADED PETROL
DIESEL FUEL
The petrol engines are designed to run on RON 95.
However, for better performance (petrol engine), we recommend RON 98.
1
2
3
A
4
V
112
C H A N G I N G B U L B S
HEADLAMP UNIT
1 Sidelamp
2 Dipped beam
3 Main beam
4 Direction indicator
Note: A light misting may appear
on the headlamp surface in certain
conditions of use.
Dipped beam
Main beam
Tilt the metallic spring holding the
fl ap giving access to the lamp
bulbs.
Open the access fl ap.
Disconnect the connector.
Disengage the retaining spring by
an forward movement, then an
outward movement to disengage
the two grips.
Take out the bulb.
Bulb: H4
Before touching, disconnect the supply connector A.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст