Ford Focus RS (2011 year). Manual — part 28
Rear Seat Cushion
Disassembly
NOTE: The rear seat double cushion is shown in
the procedure. The single cushion is similar.
1. NOTE: Retain the corner protector.
Detach the seat cushion cover from the seat
base.
• Detach the plastic retaining strip.
TIE0018735
2. Remove the seat base.
TIE0018736
3. Detach the cushion cover from each side of
the cushion.
1. Roll the cushion cover towards the center to
access the pleating hog rings.
2. Cut the hog rings.
TIE0018737
2
2
1
1
4. Remove the cushion cover.
1. Roll the cushion cover back to access the
pleating hog rings.
2. Cut the hog rings.
TIE0018738
2
1
Assembly
1. NOTE: Use hog ring pliers to close the hog
rings. Do not use any other tool. The hog
rings must be closed to overlap 8 mm as
illustrated.
G18497en
501-10-
48
Seating
501-10-
48
DISASSEMBLY AND ASSEMBLY
To assemble, reverse the disassembly
procedure.
V4001063
G18497en
501-10-
49
Seating
501-10-
49
DISASSEMBLY AND ASSEMBLY
Front Seat Backrest — 3-Door
WARNING: Note the position of the wiring
harnesses, to aid installation. An
incorrectly routed wiring harness could
become damaged when the front seat is
moved. Failure to follow this instruction
may result in personal injury.
1. Remove the side air bag module.
System, Removal and Installation).
2. Disassemble the components in the order
indicated in the following illustration(s) and
table(s).
E50114
27 Nm
27 Nm
G401855en
501-10-
50
Seating
501-10-
50
DISASSEMBLY AND ASSEMBLY
For additional information,
refer to: Side Air
Bag Module
(501-20 Supplemental Restraint
Description
Item
Front seat backrest pad
See Disassembly Detail
See Assembly Detail
1
Front seat backrest lumbar support (if
equipped)
See Disassembly Detail
2
Front seat backrest release lever cable
assembly
See Disassembly Detail
3
Description
Item
Front seat backrest frame retaining bolts
4
Front seat frame
5
Front seat backrest frame
See Disassembly Detail
See Assembly Detail
6
3. To assemble, reverse the disassembly
procedure.
Disassembly Details
Item 1
Front seat backrest pad
NOTE: Note the position of the front seat backrest
anti-squeak mat to aid assembly.
Item 2
Front seat backrest lumbar support (if
equipped)
1. Detach the front seat backrest lumbar
support adjuster from the front seat backrest
frame.
• Remove the screws.
TIE44848
2. Remove the front seat backrest lumbar
support.
1. Detach the retaining springs.
2. Detach the retaining tangs.
TIE44849
1
2
Item 3
Front seat backrest release lever cable
assembly
1. Detach the front seat backrest release lever
cables from the lower end of the front seat
backrest on both sides.
1. Detach the inner cable from the release
catch.
2. Detach the outer cable from the front seat
backrest frame.
E50112
2
1
G401855en
501-10-
51
Seating
501-10-
51
DISASSEMBLY AND ASSEMBLY
Item 6
Front seat backrest frame
1. Detach the front seat track release cable from
the lower end of the front seat backrest
frame.
E52401
Assembly Details
Item 6
Front seat backrest frame
CAUTION: After installation check for
correct operation of the front seat track
release cable.
1. NOTE: If installing a new front seat backrest
frame that is equipped with a front seat
backrest recliner handwheel, the front seat
backrest recliner handwheel drive shaft is to
be aligned.
Align the front seat backrest recliner
handwheel drive shaft.
• Front seat backrest recliner handwheel drive
shaft end protusion at the outer side of the
backrest frame XX = 25 mm.
• Clearance between the front seat backrest
frame and the front seat backrest recliner
handwheel drive shaft retaining clips YY = 2
mm.
E52385
Item 1
Front seat backrest pad
WARNING: Side air bag deployment may
be impaired if the front seat backrest pad
and anti-squeak mat are not correctly
positioned around the side air bag module.
Failure to follow this instruction may result
in personal injury.
G401855en
501-10-
52
Seating
501-10-
52
DISASSEMBLY AND ASSEMBLY
Front Seat Backrest — 4-Door/5-Door/Wagon
WARNING: Note the position of the wiring
harnesses, to aid installation. An
incorrectly routed wiring harness could
become damaged when the front seat is
moved. Failure to follow this instruction
may result in personal injury.
1. Remove the side air bag module.
System, Removal and Installation).
2. Disassemble the components in the order
indicated in the following illustration(s) and
table(s).
E50121
6
5
2
27 Nm
4
27 Nm
4
3
1
G401853en
501-10-
53
Seating
501-10-
53
DISASSEMBLY AND ASSEMBLY
Bag Module
(501-20 Supplemental Restraint
For additional information,
refer to
:
Side Air
Description
Item
Front seat backrest pad
See Disassembly Detail
See Assembly Detail
1
Front seat backrest lumbar support (if
equipped)
See Disassembly Detail
2
Front seat backrest recliner motor (if
equipped)
See Disassembly Detail
See Assembly Detail
3
Description
Item
Front seat backrest frame retaining bolts
4
Front seat frame
5
Front seat backrest frame
See Assembly Detail
6
3. To assemble, reverse the disassembly
procedure.
Disassembly Details
Item 1
Front seat backrest pad
NOTE: Note the position of the front seat backrest
anti-squeak mat to aid assembly.
Item 2
Front seat backrest lumbar support (if
equipped)
1. Detach the front seat lumbar support
adjuster from the front seat backrest frame.
• Remove the screws.
TIE44848
2. Remove the front seat backrest lumbar
support.
1. Detach the retaining springs.
2. Detach the retaining tangs.
TIE44849
1
2
Item 3
Front seat backrest recliner motor (if
equipped)
1. Remove the front seat backrest recliner
motor drive shaft inner retaining clip.
• Discard the retaining clip.
E52397
G401853en
501-10-
54
Seating
501-10-
54
DISASSEMBLY AND ASSEMBLY
2. Detach the front seat backrest recliner motor
drive shaft from the motor.
E52398
3. Remove the front seat backrest recliner
motor.
1. Disconnect the electrical connector.
2. Remove the retaining bolt.
3. Remove the retaining bolt bushes.
E52399
1
2
3
Assembly Details
Item 6
Front seat backrest frame
1. NOTE: If installing a new front seat backrest
frame that is equipped with a front seat
backrest recliner handwheel, the front seat
backrest recliner handwheel drive shaft is to
be aligned.
Align the front seat backrest recliner
handwheel drive shaft.
• Front seat backrest recliner handwheel drive
shaft end protusion at the outer side of the
backrest frame XX = 25 mm.
• Clearance between the front seat backrest
frame and the front seat backrest recliner
handwheel drive shaft retaining clips YY = 2
mm.
E52385
Item 3
Front seat backrest recliner motor (if
equipped)
NOTE: Install a new front seat backrest recliner
motor drive shaft inner retaining clip.
Item 1
Front seat backrest pad
WARNING: Side air bag deployment may
be impaired if the front seat backrest pad
and anti-squeak mat are not correctly
positioned around the side air bag module.
Failure to follow this instruction may result
in personal injury.
G401853en
501-10-
55
Seating
501-10-
55
DISASSEMBLY AND ASSEMBLY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст