Ford Focus RS (2011 year). Manual — part 81
6. Operate the roof opening panel and check
the alignment.
Item 1
Roof opening panel guide arm covers
1. NOTE: An audible click can be heard when
the lower edge of the guide arm cover is
correctly located.
Starting at the front of the roof opening
panel, install the roof opening panel guide
arm covers (left-hand side shown).
1. Install the upper clip.
2. Install the lower clip.
TIE39806
1
2
G296325en
501-17-
18
Roof Opening Panel
501-17-
18
REMOVAL AND INSTALLATION
Roof Opening Panel Shield(41 123 0)
Removal
1. Remove the roof opening panel glass.
For additional information,
refer to: Roof
Opening Panel Glass
(501-17 Roof Opening
Panel, Removal and Installation).
2. Close the roof opening panel shield.
3. Remove the roof opening panel shield front
retaining screws on both sides.
TIE40417
4. Move the roof opening panel shield forwards
to gain access to the roof opening panel
shield rear retaining screws.
5. Remove the roof opening panel shield rear
retaining screws on both sides.
TIE40417
6. Remove the roof opening panel shield.
TIE0003513
Installation
1. To install, reverse the removal procedure.
G323981en
501-17-
19
Roof Opening Panel
501-17-
19
REMOVAL AND INSTALLATION
Roof Opening Panel
NOTE: Make sure the roof opening panel is in the
closed position.
1. Remove the headliner. For additional
information, refer to: (501-05 Interior Trim
and Ornamentation)
Headliner - 3-Door, Vehicles With: Sliding
Roof Opening Panel
(Removal and
Installation),
2. Remove the components in the order
indicated in the following illustration(s) and
table(s).
TIE39809
1
3
1
4
2
3
Description
Item
Roof opening panel drain hoses
See Removal Detail
1
Roof opening panel retaining bolts
See Installation Detail
2
Description
Item
Roof opening panel retaining clips
See Removal Detail
3
Roof opening panel
See Removal Detail
See Installation Detail
4
3. To install, reverse the removal procedure.
Removal Details
G427347en
501-17-
20
Roof Opening Panel
501-17-
20
REMOVAL AND INSTALLATION
Item 1
Roof opening panel drain hoses
1. Detach the roof opening panel drain hoses
from the roof opening panel.
TIE0002865
Item 3
Roof opening panel retaining clips
1.
CAUTION: The roof opening panel front
retaining clip is fixed to the roof opening
panel frame and is not a service item.
With the aid of another technician, compress
the legs of the roof opening panel retaining
clips and lower the roof opening panel.
TIE0002872
Item 4
Roof opening panel
1. Loosen the roof opening panel locking clamp
retaining bolt by two turns on both sides.
TIE40448
Installation Details
Item 4
Roof opening panel
1. NOTE: This step should only be carried out
if installing a new roof opening panel.
Loosen the roof opening panel locking clamp
retaining bolt by two turns on both sides.
TIE40448
2. Tighten the roof opening panel locking clamp
retaining bolt on both sides.
G427347en
501-17-
21
Roof Opening Panel
501-17-
21
REMOVAL AND INSTALLATION
1. Position the roof opening panel locking
clamp.
2. Tighten the roof opening panel locking clamp
retaining bolt.
TIE40376
1
6 Nm
2
Item 2
Roof opening panel retaining bolts
1. NOTE: Do not fully tighten the roof opening
panel retaining bolts at this stage.
NOTE: The roof opening panel must be correctly
located on the retaining clips before tightening the
roof opening panel retaining bolts.
With the aid of another technician, install the
roof opening panel.
2. Tighten the roof opening panel retaining
bolts in the sequence shown.
TIE39808
10
8
6
4
2
9
7
5
3
1
6 Nm
G427347en
501-17-
22
Roof Opening Panel
501-17-
22
REMOVAL AND INSTALLATION
Roof Opening Panel Motor
1. Remove the headliner. For additional
information, refer to: (501-05 Interior Trim
and Ornamentation)
Headliner - 3-Door, Vehicles With: Sliding
Roof Opening Panel
(Removal and
Installation),
2. Remove the components in the order
indicated in the following illustration(s) and
table(s).
TIE39807
1
2
Description
Item
Roof opening panel motor electrical
connector
1
Roof opening panel motor
See Installation Detail
2
3. To install, reverse the removal procedure.
4. Carry out the initial roof opening panel motor
initialization procedure.
For additional information,
refer to: Roof
Opening Panel Motor Initialization
(501-17
Roof Opening Panel, General Procedures).
Installation Details
Item 2
Roof opening panel motor
CAUTION: The roof opening panel motor
must not be installed at this stage.
1. Starting at the rear of the roof opening panel,
remove the roof opening panel guide arm
covers (left-hand side shown).
1. Release the roof opening panel guide arm
cover lower clip.
G427348en
501-17-
23
Roof Opening Panel
501-17-
23
REMOVAL AND INSTALLATION
2. Release the roof opening panel guide arm
cover upper clip.
TIE39805
1
2
2.
CAUTION: The roof opening panel guide
pins must be aligned centrally in the flat area
of the roof opening panel guide arm as
shown.
Check the alignment of the left-hand and
right-hand roof opening panel guide pins
(left-hand side shown).
E49460
3. Adjust the left-hand roof opening panel guide
pin if necessary.
• Using a suitable screwdriver, move the roof
opening panel operating cable in the required
direction.
TIE41200
4. Adjust the right-hand roof opening panel
guide pin if necessary.
• Using a suitable screwdriver, move the roof
opening panel operating cable in the required
direction.
TIE41201
5. NOTE: This step is not necessary when
installing a new roof opening panel motor.
With the aid of another technician, support
the overhead console and connect the roof
opening panel control switch electrical
connector.
TIE41202
6. NOTE: This step is not necessary when
installing a new roof opening panel motor.
Connect the battery ground cable.
For additional information,
refer to: Battery
Disconnect and Connect
(414-01 Battery,
Mounting and Cables, General Procedures).
7.
CAUTION: This step must be carried out
if installing a previously used roof opening
panel motor.
NOTE: This step is not necessary when installing
a new roof opening panel motor.
G427348en
501-17-
24
Roof Opening Panel
501-17-
24
REMOVAL AND INSTALLATION
Carry out the erasing roof opening panel
motor initialization procedure.
For additional information,
refer to: Roof
Opening Panel Motor Initialization
(501-17
Roof Opening Panel, General Procedures).
8. NOTE: This step is not necessary when
installing a new roof opening panel motor.
Disconnect the battery ground cable.
For additional information,
refer to: Battery
Disconnect and Connect
(414-01 Battery,
Mounting and Cables, General Procedures).
9. NOTE: This step is not necessary when
installing a new roof opening panel motor.
Disconnect the roof opening panel control
switch electrical connector.
TIE41202
10. Install the roof opening panel motor.
TIE0016504
11. NOTE: An audible click can be heard when
the lower edge of the roof opening panel
guide arm cover is correctly located.
Starting at the front of the roof opening
panel, install the roof opening panel guide
arm covers (left-hand side shown).
1. Install the roof opening panel guide arm
cover upper clip.
2. Install the roof opening panel guide arm
cover lower clip.
TIE39806
1
2
G427348en
501-17-
25
Roof Opening Panel
501-17-
25
REMOVAL AND INSTALLATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст