Ford Focus RS (2011 year). Manual — part 85
• When the speed is stable, the passenger should
attempt to slowly extract the safety belt webbing
from each safety belt retractor in turn. If the
vehicle motion sensitive lock mechanism is
operating correctly, it will not be possible to
extract the webbing.
• Any safety belt retractor from which it is possible
to extract the webbing during this test must not
be used. A new safety belt must be installed.
Static Test
With the vehicle stationary and on level ground
take firm hold of the safety belt webbing (on the
tongue side of the upper safety belt anchor) and
pull out quickly. The retractor should lock within
0.25 meter (10 inches), preventing further webbing
payout. Any safety belt retractor from which it is
possible to extract further webbing must not be
used. A new safety belt must be installed.
G334014en
501-20A-
6
Safety Belt System
501-20A-
6
DIAGNOSIS AND TESTING
Front Safety Belt Retractor — 3-Door
1. Remove the B-pillar trim panel.
and Ornamentation, Removal and
Installation).
2. Remove the components in the order
indicated in the following illustration(s) and
table(s).
G407521en
501-20A-
7
Safety Belt System
501-20A-
7
REMOVAL AND INSTALLATION
For additional information, refer to:
B-Pillar
Trim Panel - 3-Door
(501-05 Interior Trim
E50742
1
3
4
35 Nm
2
G407521en
501-20A-
8
Safety Belt System
501-20A-
8
REMOVAL AND INSTALLATION
Description
Item
Safety belt lower anchor
See Removal Detail
1
Safety belt upper anchor
See Removal Detail
2
Description
Item
Guide loop
See Removal Detail
3
Safety belt retractor
See Removal Detail
See Installation Detail
4
3. To install, reverse the removal procedure.
Removal Details
Item 1
Safety belt lower anchor
CAUTION: The bolt securing the safety belt
anchor is held captive by a metal washer.
The bolt, spacer and metal washer must
remain on the safety belt anchor at all
times when the safety belt is detached or
removed.
1. Detach the safety belt lower anchor.
1. Remove the Torx bolt from the anchor rail.
2. Slide the safety belt off the anchor rail.
E50743
38 Nm
1
2
Item 2
Safety belt upper anchor
CAUTION: The bolt securing the safety belt
anchor is held captive by a metal washer.
The bolt, spacer and metal washer must
remain on the safety belt anchor at all
times when the safety belt is detached or
removed.
Item 3
Guide loop
1. Detach the guide loop from the B-pillar.
1. Rotate the guide in a clockwise direction.
2. Slide the guide outwards.
E41219
1
2
Item 4
Safety belt retractor
1. Remove the front safety belt retractor.
1. Remove the bolt.
2. Lift the retractor to detach the locating tang.
E48253
2
35 Nm
1
Installation Details
G407521en
501-20A-
9
Safety Belt System
501-20A-
9
REMOVAL AND INSTALLATION
Item 4
Safety belt retractor
CAUTION: Make sure the safety belt
retractor locating tang is correctly located.
G407521en
501-20A-
10
Safety Belt System
501-20A-
10
REMOVAL AND INSTALLATION
Front Safety Belt Retractor — 4-Door/5-Door/Wagon
1. Remove the B-pillar trim panel.
Trim and Ornamentation, Removal and
Installation).
2. Remove the components in the order
indicated in the following illustration(s) and
table(s).
E56180
35 Nm
1
2
G391262en
501-20A-
11
Safety Belt System
501-20A-
11
REMOVAL AND INSTALLATION
For additional information, refer to:
B-Pillar
Trim Panel - 4-Door/5-Door
(501-05 Interior
Description
Item
Front safety belt upper anchor retaining
bolt
See Removal Detail
1
Description
Item
Front safety belt retractor
See Removal Detail
See Installation Detail
2
3. To install, reverse the removal procedure.
Removal Details
Item 1
Front safety belt upper anchor retaining
bolt
1.
CAUTION: The bolt securing the front
safety belt upper anchor is held captive by
a metal washer. The bolt, spacer and metal
washer must remain on the front safety belt
upper anchor at all times when the front
safety belt is detached or removed.
Detach the front safety belt upper anchor
from the front safety belt shoulder height
adjuster.
Item 2
Front safety belt retractor
1. Remove the front safety belt retractor.
1. Remove the front safety belt retractor
retaining bolt.
2. Lift the front safety belt retractor to detach
the locating tang.
E48253
2
35 Nm
1
Installation Details
Item 2
Front safety belt retractor
CAUTION: Make sure that the front safety
belt retractor locating tang is correctly
located.
G391262en
501-20A-
12
Safety Belt System
501-20A-
12
REMOVAL AND INSTALLATION
Rear Safety Belt Retractor — 3-Door/5-Door/Wagon
1. Remove the components in the order
indicated in the following illustration(s) and
table(s).
E48249
2
38 Nm
1
40 Nm
3
4
Description
Item
Safety belt lower anchor retaining bolt
See Removal Detail
1
Safety belt retractor cover
See Removal Detail
2
Description
Item
Safety belt upper anchor retaining bolt
3
Safety belt retractor
See Installation Detail
4
2. To install, reverse the removal procedure.
G391263en
501-20A-
13
Safety Belt System
501-20A-
13
REMOVAL AND INSTALLATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст