Ford Focus RS (2011 year). Manual — part 31
Glass, Frames and Mechanisms — Vehicles With: Global Closing
schematic and connector information.
General Equipment
Worldwide diagnostic system (WDS)
Inspection and Verification
1. Verify the customer concern.
2. Visually inspect for obvious signs of mechanical
or electrical damage.
Visual Inspection Chart
Electrical
Mechanical
• Fuse(s)
• Electrical
connector(s)
• Switch(es)
• Circuit(s)
• Window seal
• Door window frame
3. Initialize the door window motors.
(501-11 Glass, Frames and Mechanisms,
General Procedures).
4. If an obvious cause for an observed or reported
concern is found, correct the cause (if possible)
before proceeding to the next step.
5. If the cause is not visually evident, verify the
symptom and refer to WDS.
G330087en
501-11-
17
Glass, Frames and Mechanisms
501-11-
17
DIAGNOSIS AND TESTING
REFER to
:
Door Window Motor Initialization
Refer to
Wiring Diagrams Section 501-11
, for
Door Window Motor Initialization
WARNING: The door window anti-trap
function will not operate during the door
window motor initialization procedure.
Make sure that the door window opening
is free of all foreign material. Failure to
follow this instruction may result in
personal injury.
NOTE: After the battery has been disconnected it
is necessary to initialize each door window motor
separately.
NOTE: If a single door window motor has been
disconnected, it is necessary to initialize that door
window motor.
NOTE: If the fuse for a front or rear door window
motor has been disconnected, it is necessary to
initialize that door window motor.
NOTE: If the battery junction box (BJB) fuse for
the front power windows has been disconnected,
it is necessary to initialize both front door window
motors.
NOTE: If the battery junction box (BJB) fuse for
the rear power windows has been disconnected,
it is necessary to initialize both rear door window
motors.
NOTE: Leave a period of at least one minute
before connecting the battery, fuse or door window
motor(s).
All vehicles
1. Press and hold the power window control
switch close button until the door window is
fully closed.
2. Release the power window control switch
close button and press again for three
seconds.
3. Briefly press the power window control
switch open button to the second detent and
release the button.
• The door window should open automatically.
4. Briefly press the power window control
switch close button to the second detent and
release the button.
• If the door window does not close
automatically, repeat the complete
procedure.
5. Repeat the door window motor initialization
for each door window motor.
Convertible
6. Press and hold the convertible top switch
CLOSE button until the convertible top is
fully closed. Hold the switch closed for three
seconds.
G323942en
501-11-
18
Glass, Frames and Mechanisms
501-11-
18
GENERAL PROCEDURES
Front Door Window Glass
1. Remove the front door trim panel. For
additional information, refer to: (501-05
and Installation),
Installation).
2. Remove the components in the order
indicated in the following illustration(s) and
table(s).
E39517
1
2
3
Description
Item
Front door panel grommets
1
Front door interior weatherstrip
2
Front door window glass
3
3. To install, reverse the removal procedure.
Removal Details
Item 2
Front door interior weatherstrip
CAUTION: To avoid damage, care must be
taken when removing the front door
interior weatherstrip.
G427344en
501-11-
19
Glass, Frames and Mechanisms
501-11-
19
REMOVAL AND INSTALLATION
Front Door Trim Panel - 3-Door
(Removal
Front Door Trim Panel -
Interior Trim and Ornamentation)
4-Door/5-Door/Wagon
(Removal and
See Removal Detail
See Installation Detail
See Removal Detail
Item 3
Front door window glass
1. Connect the front door power window control
switch electrical connector.
TIE0028859
2. Connect the battery ground cable.
Mounting and Cables, General Procedures).
3. Loosen the front door window glass clamp
retaining bolts by two turns.
• Align the front door window glass clamp
retaining bolts with the access holes.
TIE39519
8 Nm
4. NOTE: The front door window glass must be
removed towards the outside of the window
opening.
Remove the front door window glass.
1. Lift the front door window glass.
2. Tip the front door window glass forwards and
remove it from the front door.
TIE0028861
1
2
Installation Details
Item 3
Front door window glass
NOTE: The front door window glass must be
installed from the outside of the window opening.
G427344en
501-11-
20
Glass, Frames and Mechanisms
501-11-
20
REMOVAL AND INSTALLATION
Disconnect and Connect
(414-01 Battery,
For additional information,
refer to: Battery
Rear Door Window Glass — Vehicles With: Manual Windows
1. Remove the rear door trim panel.
Door Trim Panel - Vehicles With: Manual
Windows
(501-05 Interior Trim and
Ornamentation, Removal and Installation).
2. Remove the components in the order
indicated in the following illustration(s) and
table(s).
E39520
1
3
2
Description
Item
Grommets
1
Interior weatherstrip
See Removal Detail
2
Window glass
See Removal Detail
See Installation Detail
3
3. To install, reverse the removal procedure.
Removal Details
Item 2
Interior weatherstrip
CAUTION: Carefully remove the interior
weatherstrip to avoid damage.
G296305en
501-11-
21
Glass, Frames and Mechanisms
501-11-
21
REMOVAL AND INSTALLATION
For additional information,
refer to: Rear
Item 3
Window glass
1. Install the window regulator handle.
TIE0028854
2. Fully lower the window glass.
3. Position the lower part of the door glass top
run outside the door.
E0001161
4. Loosen the rear door window glass clamp
retaining bolts two complete turns.
• Align the window glass clamp retaining bolts
with the access holes.
TIE39521
8 Nm
5. NOTE: The rear door window glass must be
removed towards the outside of the window
opening.
Remove the rear door window glass.
1. Lift the window glass.
2. Tip the window glass outwards and remove
the window glass from the rear door.
TIE0031998
1
2
Installation Details
Item 3
Window glass
NOTE: The rear door window glass must be
installed from the outside of the window opening.
G296305en
501-11-
22
Glass, Frames and Mechanisms
501-11-
22
REMOVAL AND INSTALLATION
Rear Door Window Glass — Vehicles With: Power Windows
1. Remove the rear door trim panel.
For additional information,
refer to: Rear
Door Trim Panel - Vehicles With: Power
Windows
(501-05 Interior Trim and
Ornamentation, Removal and Installation).
2. Remove the components in the order
indicated in the following illustration(s) and
table(s).
E39533
1
3
2
Description
Item
Grommets
1
Interior weatherstrip
See Removal Detail
2
Window glass
See Removal Detail
3
3. To install, reverse the removal procedure.
Removal Details
Item 2
Interior weatherstrip
CAUTION: Carefully remove the interior
weatherstrip to avoid damage.
G296306en
501-11-
23
Glass, Frames and Mechanisms
501-11-
23
REMOVAL AND INSTALLATION
See Installation Detail
Item 3
Window glass
1. Connect the power window control switch
electrical connector.
TIE0028859
2. Fully lower the window glass.
3. Position the lower part of the door glass top
run outside the door.
E0001161
4. Loosen the rear door window glass clamp
retaining bolts two complete turns.
• Align the window glass clamp retaining bolts
with the access holes.
TIE39534
8 Nm
5. NOTE: The rear door window glass must be
removed towards the outside of the window
opening.
Remove the rear door window glass.
1. Lift the window glass.
2. Tip the window glass outwards and remove
the window glass from the rear door.
TIE0031998
1
2
Installation Details
Item 3
Window glass
NOTE: The rear door window glass must be
installed from the outside of the window opening.
G296306en
501-11-
24
Glass, Frames and Mechanisms
501-11-
24
REMOVAL AND INSTALLATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст