Ford E-350 (2012 year). Manual — part 18

WARNING (Continued)

• Never place floor mats or any other covering on top of already

installed floor mats. Floor mats should always rest on top of vehicle
carpeting surface and not another floor mat or other covering.
Additional floor mats or any other covering will reduce the pedal
clearance and potentially interfere with pedal operation.

• Check attachment of floor mats on a regular basis. Always properly

reinstall and secure floor mats that have been removed for cleaning
or replacement.

• Always make sure that objects cannot fall into the driver foot well

while the vehicle is moving. Objects that are loose can become
trapped under the pedals causing a loss of vehicle control.

• Failure to properly follow floor mat installation or attachment

instructions can potentially cause interference with pedal operation
causing loss of control of vehicle.

• To install floor mats, position the floor mat so that the eyelet is over

the retention post and press down to lock in.

• To remove the floor mat, reverse the installation procedure.

Driver Controls

74

KEYS

The key operates all locks on your vehicle. You should always carry a
second key with you in a safe place in case you require it in an
emergency.

If your vehicle is equipped with the SecuriLock

威 passive anti-theft

system, your keys are electronically coded to your vehicle; using a
non-coded key will not permit your vehicle to start. If you lose your
dealer supplied keys, replacement keys are available through your
authorized dealer.

POWER DOOR LOCKS (IF EQUIPPED)

Press control to unlock all doors.

Press control to lock all doors.

Memory lock

If you lock your doors with the power lock switch or the remote
transmitter while the sliding door is open, the door will automatically
lock after it is closed.

Autolock feature

Note: Your vehicle comes with the autolock feature disabled.

The autolock feature will lock all the doors when:
• all the doors are closed,
• the ignition is in the on position,
• you shift into any gear putting the vehicle in motion, and
• the vehicle attains a speed greater than 12 mph (20 km/h) for greater

than two seconds.

Locks and Security

75

The autolock feature repeats when:
• any door is opened then closed while the ignition is in the on position

and the vehicle speed is 9 mph (15 km/h) or lower, and

• the vehicle then attains a speed greater than 12 mph (20 km/h) for

greater than two seconds.

Deactivating/activating autolock feature

Your vehicle comes with the autolock feature disabled; there are three
methods to enable/disable this feature:
• Through your authorized dealer, or
• by using a power door unlock/lock procedure, or
• by using the instrument cluster message center (if equipped). Refer to

Message center in the Instrument Cluster chapter.

Note: The autolock feature can be activated/deactivated independently
of the autounlock feature.

Power door lock switch autolock enable/disable procedure

Before starting, ensure the ignition is in the off position and all vehicle
doors are closed. You must complete Steps 1–5 within 30 seconds or the
procedure will have to be repeated. If the procedure needs to be
repeated, wait a minimum of 30 seconds before beginning again.

1. Place the key in the ignition and turn the ignition to the on position.

2. Press the power door unlock
control on the door panel three
times.

3. Turn the ignition from the on
position to the off position.

4. Press the power door unlock
control on the door panel three
times.

5. Turn the ignition back to the on position. The horn will chirp one time
to confirm programming mode has been entered and is active.

6. To enable/disable the autolock feature, press the unlock control, then
press the lock control. The horn will chirp once if autolock was
deactivated or twice (one short and one long chirp) if autolock was
activated.

7. Turn the ignition to the off position. The horn will chirp once to
confirm the procedure is complete.

Locks and Security

76

Autounlock feature

After the autolock feature has locked the doors, the autounlock feature
will unlock all the doors when:
• the vehicle has then come to a stop and the ignition is turned off or to

accessory; and

• the driver door is opened within 10 minutes of the ignition being

turned off or to accessory.

Note: The doors will not autounlock if the vehicle has been
electronically locked before the driver door is opened.

Deactivating/activating autounlock feature

Your vehicle comes with the autounlock features disabled; there are
three methods to enable/disable this feature:
• Through your authorized dealer, or
• by using a power door unlock/lock sequence, or
• by using the instrument cluster message center (if equipped). Refer to

Message center in the Instrument Cluster chapter.

Note: The autounlock feature can be activated/deactivated
independently of the autolock feature.

Power door lock switch autounlock enable/disable procedure

Before starting, ensure the ignition is off and all vehicle doors are closed.
You must complete Steps 1–5 within 30 seconds or the procedure will
have to be repeated. If the procedure needs to be repeated, wait a
minimum of 30 seconds before beginning again.

1. Turn the ignition on.

2. Press the power door unlock
control on the door panel three
times.

3. Turn the ignition off.

4. Press the power door unlock
control on the door panel three
times.

5. Turn the ignition back on. The horn will chirp one time to confirm
programming mode has been entered and is active.

Locks and Security

77