Ford E-350 (2012 year). Manual — part 17

SPEED CONTROL (IF EQUIPPED)

With speed control set, you can maintain a set speed without keeping
your foot on the accelerator pedal.

WARNING: Do not use the speed control in heavy traffic or on
roads that are winding, slippery or unpaved.

Using speed control

The speed controls are located on the steering wheel. The following
buttons work with speed control.

ON: Press to turn on speed control.

OFF: Press to turn off speed
control.

RES (Resume): Press to resume a
set speed.

SET/ACCEL: Press to set a speed
or increase a set speed.

COAST: Press to reduce a set speed.

Setting speed control

1. Press and release ON.

2. Accelerate to the desired speed.

3. Press and release SET/ACCEL.

4. Take your foot off the accelerator pedal.

5. The indicator

light on the instrument cluster will turn on.

Note:
• Vehicle speed may vary momentarily when driving up and down a

steep hill.

• If the vehicle speed increases above the set speed on a downhill, you

may want to apply the brakes to reduce the speed.

• If the vehicle speed decreases more than 10 mph (16 km/h) below

your set speed on an uphill, your speed control will disengage.

Disengaging speed control

To disengage speed control, press the brake pedal. Disengaging speed
control will not erase the previous set speed.

Driver Controls

70

Resuming a set speed

Press and release RES. This will automatically return the vehicle to the
previously set speed.

Increasing speed while using speed control

To increase the set speed:
• Press and hold SET/ACCEL until you get to the desired speed, then

release. You can also use SET/ACCEL to operate the tap-up function.
Press and release SET/ACCEL to increase the vehicle set speed in
1 mph (1.6 km/h) increments.

• Use the accelerator pedal to get to the desired speed. When the

vehicle reaches that speed, press and release SET/ACCEL.

Reducing speed while using speed control

To reduce the set speed:
• Press and hold COAST until you get to the desired speed, then

release. You can also use COAST to operate the tap-down function.
Press and release COAST to decrease the vehicle set speed in 1 mph
(1.6 km/h) increments.

• Press the brake pedal until the desired vehicle speed is reached, then

press and release SET/ACCEL.

Turning off speed control

To turn off the speed control, press OFF or turn off the ignition.

Note: When you turn off the speed control or the ignition, your speed
control set speed memory is erased.

STEERING WHEEL CONTROLS (IF EQUIPPED)

SYNC

威 system hands free

control feature (if equipped)

Press

briefly to use the voice

command feature. You will hear a
tone and LISTENING will appear in
the radio display. Press and
hold

to exit voice command.

Press

to activate phone mode or answer a phone call. Press and

hold

to end a call or exit phone mode.

For further information on the SYNC

威 system, refer to the SYNC威

supplement.

Driver Controls

71

Navigation system/SYNC

威 hands

free control features (if
equipped)

Press

control briefly until the

voice

icon appears on the

Navigation display to use the voice
command feature.

Press

to activate phone mode or answer a phone call. Press and

hold

to exit phone mode or end a call.

For further information on the Navigation system/SYNC

威 system, refer to

the Navigation System and SYNC

威 supplements.

UPFITTER CONTROLS (IF EQUIPPED)

Your vehicle may be equipped with
the Upfitter option package which
will provide four switches, mounted
in the center of the instrument
panel, labeled AUX 1, AUX 2, AUX 3
and AUX 4. These switches will only
operate while the ignition is in the
on position, whether the engine is
running or not. It is, however, recommended that the engine remain
running to maintain battery charge when using the Upfitter switches for
extended duration or higher current draws.

When switched on by the operator they provide 10 amps, 15 amps or
30 amps of electrical battery power for a variety of personal or
commercial uses.

If your vehicle is equipped with this option, a relay/fuse kit will be
included. This kit contains the required fuses and relays that need to be
installed into the Power Distribution Box located under the hood. Refer
to the instruction sketch included in the kit and Fuses and Relays in
the Roadside Emergencies chapter. See your authorized dealer for
service.

There will also be one power lead for each switch found as a blunt-cut
and sealed wire located in the underhood cowl shield above the engine
block PCM.

Driver Controls

72

They are coded as follows:

Switch

Circuit number

Wire color

Fuse

AUX 1

CAC05

Yellow

30A

AUX 2

CAC06

Green with
Brown Trace

30A

AUX 3

CAC07

Violet with
Green Trace

10A

AUX 4

CAC08

Brown

15A

More detailed information about Upfitter switches can be found at
https://www.fleet.ford.com/truckbbas/.

POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)

WARNING: Always use floor mats that are designed to fit the
foot well of your vehicle. Only use floor mats that leave the pedal

area unobstructed. Only use floor mats that are firmly secured to
retention posts so that they cannot slip out of position and interfere
with the pedals or impair safe operation of your vehicle in other ways.
• Pedals that cannot move freely can cause loss of vehicle control and

increase the risk of serious personal injury.

• Always make sure that the floor mats are properly attached to the

retention posts in the carpet that are supplied with your vehicle.
Floor mats must be properly secured to both retention posts to
ensure mats do not shift out of position.

• Never place floor mats or any other covering in the vehicle foot well

that cannot be properly secured to prevent them from moving and
interfering with the pedals or the ability to control the vehicle.

Driver Controls

73