Hyundai Kona (2018 year). Manual — part 18
ISG (IDLE STOP AND GO) SYSTEM (IF EQUIPPED)
The ISG system is to reduce the fuel
To activate the ISG system
i
Information
consumption by automatically shut-
Prerequisite for activation
ting down the engine, when the vehi-
cle is at a standstill (i.e. red stop light,
The ISG system operates in the fol-
stop sign, and traffic jam).
lowing situations.
The engine is automatically started
-
The driver's seatbelt is fastened.
upon satisfying the starting condi-
-
The driver's door and the hood are
tions.
closed.
The ISG system is always active,
-
The brake vacuum pressure is
when the engine is running.
adequate.
-
The battery is sufficiently charged.
i
Information
-
The outside temperature is between
-20 °C and 35 °C (-4 °F and 95 °F).
When the engine is automatically
OOS057013
5
started by the ISG system, some warn-
-
The engine coolant temperature is
•
The ISG system is not activated,
ing lights (i.e. ABS, ESC, ESC OFF,
not too low.
when the prerequisites to activate
EPS, and parking brake warning
-
The system is not in the diagnostic
the ISG system are unsatisfied. In
light) may illuminate for a few sec-
mode.
this case, the ISG OFF button indi-
onds due to the low battery voltage.
-
The steering wheel is not steered
cator illuminates, and the auto stop
However, it does not indicate a mal-
excessively. (for dual clutch trans-
indicator (
) illuminates in yellow
function with the ISG system.
mission vehicle)
on the instrument cluster.
-
The vehicle is driven on a steep
•
When the above indicator remains
incline.
(for dual clutch transmis-
illuminated on the instrument clus-
sion vehicle)
ter, we recommend that you have
the IGS system checked by an
authorized HYUNDAI dealer.
5-47
Driving your vehicle
Auto stop
In auto stop mode, when the driver
i
Information
opens the hood, the ISG system will
The driving speed must reach at least
be deactivated.
10 km/h (6 mph) after an idle stop to
When the system is deactivated:
stop the engine in idle stop mode
again.
Dual clutch transmission vehicle
1. Decrease the vehicle speed to 0
km/h.
2. Depress the brake pedal with the
shift lever in D
(Drive) or N
OOS057088L
(Neutral).
To stop the engine in idle stop mode
The auto stop indicator (
) illumi-
nates in green on the instrument
Manual transmission vehicle
cluster, when the engine stops.
OOS057059L
1. Decrease the vehicle speed to 5
The ISG OFF button indicator illumi-
km/h (3 mph).
i
Information
nates.
2. Set the gear in N (Neutral).
The driving speed must reach at least
3. Release the clutch pedal.
8 km/h (5 mph) after an idle stop to
The auto stop indicator (
) illumi-
stop the engine in idle stop mode
nates in green on the instrument
again.
cluster, when the engine stops.
5-48
Auto start
The engine is automatically restart-
ed in the following situations.
To restart the engine in the auto
stop mode
-
The fan speed of the manual cli-
mate control system is set above
Manual transmission vehicle
the 3rd position, with the air condi-
• Depress the clutch pedal with the
tion ON.
gear in N (Neutral).
-
The fan speed of the automatic cli-
The auto stop indicator (
) goes
mate control system is set above
OFF on the instrument cluster, when
the 6th position, with the air condi-
the engine is restarted.
tion ON.
-
A certain period of time has
OTLE055036
Dual clutch transmission vehicle
elapsed with the air condition ON.
The message, "Auto Stop deactivat-
• Release the brake pedal.
-
The defroster is activated.
ed. Start manually", appears on the
• When Auto Hold is activated, if you
5
-
The brake vacuum pressure is low.
LCD display with a beep sound.
release the brake pedal, the
-
The battery is weak.
engine will be in the auto stop
-
The driving speed exceeds 5 km/h
At this time, restart the vehicle man-
state. However, if you depress the
(3 mph). (for manual transmission
ually by:
accelerator pedal, the engine will
vehicle)
start again.
Manual transmission vehicle
-
The driving speed exceeds 2 km/h
The auto stop indicator (
) goes
Depressing the clutch and brake
(1.2 mph). (for dual clutch trans-
pedal with the gear in neutral.
OFF on the instrument cluster, when
mission vehicle)
the engine is restarted.
-
The vehicle is shifted to P (Park) or
Dual clutch transmission vehicle
R (Reverse) when the brake pedal
Depressing the brake pedal with the
is depressed.
shift lever in P (Park) or N (Neutral).
But for your safety, restart the vehicle
in the P (Park) position.
5-49
Driving your vehicle
- The door is opened or seat belt is
The auto start is temporarily deac-
unfastened when the brake pedal
tivated in the following situations.
is depressed.
The auto stop indicator (
) blinks
in green for 5 seconds on the instru-
ment cluster and a message "Auto
Start" will appear on the LCD display.
OAD055087L
Dual clutch transmission vehicle
When the shift lever is shifted from N
OTLE055037
(Neutral) to R (Reverse), D (Drive) or
Manual transmission vehicle
Manual shift mode without the brake
When the gear is shifted without the
pedal depressed. A message "Press
clutch pedal depressed. A message
brake pedal for Auto Start" will
"Press clutch pedal for Auto Start"
appear on the LCD display. To acti-
will appear on the LCD display. To
vate auto start, depress the brake
activate auto start, shift to neutral
pedal.
and depress the clutch pedal.
5-50
To deactivate the ISG system
ISG system malfunction
i
Information
• Press the ISG OFF button to deac-
The ISG system may not operate:
• When you cannot turn OFF the ISG
tivate the ISG system. Then, the
When there is a malfunction with the
OFF button indicator by pressing the
ISG OFF button indicator illumi-
ISG sensors or the ISG system.
ISG OFF button, or when the mal-
nates, and the message "Auto
function with the ISG system per-
Stop System Off" appears on the
sists, we recommend that you contact
LCD display.
The followings occur, when there is
an authorized HYUNDAI dealer.
a malfunction with the ISG system:
• Press the ISG OFF button again to
• You can turn off the ISG OFF but-
reactivate the ISG system. Then,
• The auto stop indicator (
) will
ton indicator by driving over
80
the ISG OFF button indicator turns
blink in yellow on the instrument
km/h (50 mph) for up to 2 hours
OFF.
cluster.
with the fan speed below the 2nd
• The light on the ISG OFF button
position. If the ISG OFF button
will illuminate.
indicator remains ON, we recom-
mend that you contact an author-
5
ized HYUNDAI dealer.
WARNING
When the engine is in auto stop
mode, the engine may restart.
Before leaving the vehicle or
checking the engine compart-
ment, stop the engine by plac-
ing the ignition switch to the
LOCK/OFF position or remov-
ing the ignition key.
5-51
Driving your vehicle
The battery sensor deactiva-
Prerequisites to reactivate the
NOTICE
tion
battery sensor
•
Use only the genuine HYUNDAI
Keep the engine in the OFF status
ISG battery for replacement. If
for 4 hours, and attempt to restart the
not, the ISG system may not nor-
engine 3 to 4 times for the battery-
mally operate.
sensor reactivation.
•
Do not recharge the ISG battery
Pay extreme caution not to connect
with a general battery charger. If
any accessories (i.e. navigation and
not, it may damage or explode
black box) to the vehicle with the
the ISG battery.
engine in the OFF status. If not, the
•
Do not remove the battery cap. If
battery sensor may not be reactivat-
ed.
not, the battery electrolyte,
which is harmful to the human
body, may leak out.
OOS057015L
i
Information
[A] : Battery sensor
The ISG system may not operate in
The battery sensor is deactivated,
the following situations.
when the battery is disconnected
- There is a malfunction with the IGS
from the negative pole for mainte-
system.
nance purpose.
- The battery is weak.
In this case, the ISG system is limit-
- The brake vacuum pressure is low.
edly operated due to the battery sen-
In those cases, we recommend that
sor deactivation. Thus, the driver
you have the ISG system checked by
needs to take the following proce-
an authorized HYUNDAI dealer.
dures to reactivate the battery sen-
sor after disconnecting the battery.
5-52
DRIVE MODE INTEGRATED CONTROL SYSTEM (IF EQUIPPED)
The mode changes, as below,
When ECO mode is activated:
whenever the DRIVE MODE button
• The acceleration response may be
is pressed.
slightly reduced as the accelerator
ECO
pedal is depressed moderately.
(if equipped)
• The air conditioner performance
may be limited.
COMFORT
SPORT
• The shift pattern of the dual clutch
transmission may change.
When COMFORT mode is selected,
• The engine noise may get louder.
it is not displayed on the instrument
cluster.
OOS057060
The above situations are normal
The drive mode may be selected
conditions when ECO mode is acti-
ECO mode (if equipped)
according to the driver's preference
vated, to improve fuel efficiency.
When the Drive Mode is
5
or road condition.
set to ECO mode, the
The system resets to be in the COM-
engine and transmission
FORT mode (except if it is in ECO
control logic are changed
mode), when the engine is restarted.
to maximize fuel efficiency.
• When the ECO mode is selected by
i
Information
pressing the DRIVE MODE button,
If there is a problem with the instru-
the ECO indicator will illuminate.
ment cluster, the drive mode will be in
• If the vehicle is set to ECO mode,
COMFORT mode and may not
when the engine is turned OFF and
change to SPORT mode.
restarted, the Drive Mode setting
will remain in ECO mode.
i
Information
Fuel efficiency depends on the driver's
driving habit and road condition.
5-53
Driving your vehicle
Limitation of ECO mode opera-
SPORT mode
COMFORT mode
tion:
SPORT mode manages
COMFORT mode is a
If the following conditions occur while
the driving dynamics by
base mode.
ECO mode is operating, the system
automatically adjusting the
operation is limited even though
steering effort, the engine
When COMFORT mode is selected
there is no change in ECO indicator.
and transmission control
by pressing the DRIVE MODE but-
•
When the coolant temperature is
logic for enhanced driving
ton, the COMFORT indicator will illu-
performance.
low:
minate.
•
When SPORT mode is selected by
The system will be limited until
If the vehicle is set to COMFORT
engine performance becomes nor-
pressing the DRIVE MODE button,
mode, when the engine is turned
the SPORT indicator will illuminate.
mal.
OFF and restarted, the Drive Mode
•
When driving up a hill:
•
Whenever the engine is restarted,
setting will remain in COMFORT
the Drive Mode will revert back to
mode.
The system will be limited to gain
COMFORT mode. If SPORT mode
power when driving uphill because
is desired, re-select SPORT mode
engine torque is restricted.
from the DRIVE MODE button.
•
When driving the vehicle with the
•
When SPORT mode is activated:
dual clutch transmission gear shift
- The engine rpm will tend to remain
lever in manual shift mode:
raised over a certain length of time
The system will be limited due to
even after releasing the accelerator
the shift location.
- Upshifts are delayed when accel-
•
When the accelerator pedal is
erating
deeply depressed for a few seconds:
The system will be limited, judging
i
Information
that the driver wants to speed up.
In SPORT mode, the fuel efficiency
may decrease.
5-54
BLIND-SPOT COLLISION WARNING (BCW) SYSTEM (IF EQUIPPED)
(1) BCW : Blind spot area
(3) RCCW
(Rear Cross-Traffic
Collision Warning)
The BCW range varies relative to
vehicle speed. Note that if your
The RCCW feature monitors
A
vehicle is traveling much faster
approaching cross traffic from the
than the vehicles around you, the
left and right side of the vehicle
warning will not occur.
when your vehicle is in reverse.
The feature will operate when the
(2) BCW : Closing at high speed
vehicle is moving in reverse below
The BCW-Closing at high speed
B
about 10 km/h (6 mph). If oncom-
feature will alert you when a vehi-
ing cross traffic is detected a
cle is approaching in an adjacent
warning chime will sound.
lane at a high rate of speed. If the
driver activates the turn signal
Distance from the approaching
vehicle can be seen differently
when the system detects an
oncoming vehicle, the system
according to the relative speed.
5
sounds an audible alert. Distance
from the approaching vehicle can
be seen differently according to
OOS057099L
the relative speed.
[A] : Blind spot area
[B] : Closing at high speed
The Blind-spot Collision Warning
(BCW) system uses radar sensors in
the rear bumper to monitor and warn
the driver of an approaching vehicle
in the driver's blind spot area.
The system monitors the rear area of
the vehicle and provides information
to the driver with an audible alert and
an indicator on the outside rearview
mirrors.
5-55
Driving your vehicle
BCW (if equipped)
To cancel:
WARNING
Operating conditions
Press the BCW switch again. The
indicator on the switch will go off.
•
Always be aware of road con-
ditions while driving and be
When the system is not used, turn the
alert for unexpected situa-
system off by turning off the switch.
tions even though the Blind-
Spot Collision Warning (BCW)
i
Information
system is operating.
• If the vehicle is turned off then on
•
The Blind-spot Collision
again, the BCW system returns to
Warning (BCW) system is not
the previous state.
a substitute for proper and
• When the system is turned on, the
safe driving. Always drive
warning light will illuminate for 3
safely and use caution when
seconds on the outside rearview
changing lanes or backing up
OOS057023
mirror.
the vehicle. The Blind-spot
To operate:
Collision Warning (BCW) sys-
tem may not detect every
Press the BCW switch with the
The function will activate when:
object alongside the vehicle.
Ignition switch in the ON position.
1. The function is on.
The indicator on the BCW switch will
2. The vehicle speed is above
illuminate. When the vehicle speed
approximately 30 km/h (20 mph).
exceeds 30 km/h (20 mph), the sys-
3. An oncoming vehicle is detected in
tem will be activated.
the blind spot area.
5-56
■ Left side
■ Left side
■ Right side
■ Right side
OOS057024
OOS057025
OOS057026
First stage alert
[A] : Warning sound
If a vehicle is detected within the
Second stage alert
5
boundary of the system, a yellow
A warning chime to alert the driver will activate when:
warning light will illuminate on the
1. A vehicle has been detected in the blind spot area by the radar system
outside rearview mirror.
(the warning light will illuminate on the outside rearview mirror (i.e, in
Once the detected vehicle is no
the first stage alert)) AND
longer within the blind spot area, the
2. The turn signal is applied (same side as where the vehicle is being
warning will turn off depending on
detected).
the driving conditions of the vehicle.
When this alert is activated, the warning light on the outside rearview mir-
ror will also blink.
If you turn off the turn signal indicator, the second stage alert (the warning
chime and the blinking warning light on the outside rearview mirror) will be
deactivated.
5-57
Driving your vehicle
• The warning chime may be deacti-
RCCW (Rear Cross-Traffic
i
Information
vated.
Collision Warning)
If the vehicle is turned off then on
- To deactivate the warning chime:
(if equipped)
again, the BCW system returns to the
Go to the "User Settings Driver
The Rear Cross-Traffic Collision
previous state.
Assistance and deselect Blind-spot
warning function monitors approach-
The system will activate when vehicle
Collision Warning sound" on the
ing cross traffic from the left and right
speed is below 10 km/h (6.2 mph) and
LCD display.
side of the vehicle when your vehicle
with the shift lever in R (Reverse).
- To activate the warning chime:
is in reverse.
The Rear Cross-Traffic Collision
Go to the "User Settings Driver
warning detecting range is approxi-
Assistance and select Blind-spot
Operating conditions
mately 0.5 m ~ 20 m (1 ft ~ 65 ft) in the
Collision Warning sound" on the
To operate:
direction of both lateral sides of the
LCD display.
vehicle. An approaching vehicle will
Go to the 'User Settings Driver
be detected if their vehicle speed is
Assistance and select Rear Cross-
i
Information
within 4 km/h ~ 36 km/h (2.5 ~ 22.5
Traffic Collision warning' on the LCD
mph).
The warning chime function helps
display.
Note that the detecting range may
alert the driver. Deactivate this func-
vary under certain conditions. As
tion only when it is necessary.
The system will turn on and standby
always, use caution and pay close
Refer to "User settings mode" in
to activate. If you deactivate this
attention to your surroundings when
chapter 3 for more details.
function in the cluster, the system will
backing up your vehicle.
stop.
Refer to "User settings mode" in
chapter 3 for more details.
5-58
Warning type
i
Information
WARNING
■ Left
■ Right
•
The warning chime will turn off
when:
•
When BCW is activated, the
warning light on the outside
- The detected vehicle moves out of
rearview mirror will illuminate
the sensing area or
whenever a vehicle is detect-
- when the vehicle is right behind
ed at the rear side by the sys-
your vehicle or
tem.
- when the vehicle is not approach-
To avoid accidents, do not
ing your vehicle or
focus only on the warning
- when the other vehicle slows down.
light and neglect to see the
•
The system may not operate properly
surrounding of the vehicle.
OOS057031/OOS057032
due to other factors or circumstances.
•
Drive safely even though the
Always pay attention to your sur-
5
If the vehicle detected by the sensors
vehicle is equipped with a
approaches your vehicle, the warn-
roundings.
Blind-spot Collision Warning
ing chime will sound, the warning
•
If the sensing area near the rear
(BCW) system and Rear Cross
light on the outside rearview mirror
bumper is blocked by either a wall
Traffic Alert
(RCTA). Do not
will blink and a message will appear
or barrier or by a parked vehicle,
solely rely on the system but
on the LCD display.
the system sensing area may be
check your surrounding
reduced.
before changing lanes or
backing the vehicle up.
The system may not alert the
driver in some conditions so
always check your surround-
ings while driving.
5-59
Driving your vehicle
Detecting sensor
Warning message
• The Blind-spot Collision
Warning (BCW) system and
Rear Cross-Traffic Collision
warning
(RCCW) are not a
substitute for proper and safe
driving practices. Always
drive safely and use caution
when changing lanes or back-
ing up your vehicle. The Blind-
spot Collision Warning (BCW)
system may not detect every
object alongside the vehicle.
OOS057027
OOS057077L
NOTICE
The sensors are located inside the
Blind-Spot Collision Warning
rear bumper.
(BCW) system disabled.
• The system may not work prop-
Radar blocked
erly when the bumper has been
Always keep the rear bumper clean
damaged, or if the rear bumper
for proper operation of the system.
• This warning message may appear
has been replaced or repaired.
when :
• The sensing range differs some-
- One or both of the sensors on the
what according to the width of
rear bumper is blocked by dirt or
the road. When the road is nar-
snow or a foreign object.
row, the system may detect
- Driving in rural areas where the
other vehicles in the next lane
BCW sensor does not detect
OR when the road is wide, the
another vehicle for an extended
system may not detect other
period of time.
vehicles in the next lane.
- When there is inclement weather
• The system may turn off due to
such as heavy snow or rain.
strong electromagnetic waves.
5-60
- A trailer or carrier is installed. To
■ Type A
■ Type B
Limitations of the system
use the BCW system, remove the
The driver must be cautious in the
trailer or carrier from your vehicle.
below situations, because the sys-
If any of these conditions occur, the
tem may not detect other vehicles or
light on the BCW switch and the sys-
objects in certain circumstances.
tem will turn off automatically.
When the BCW canceled warning
•
When a trailer or carrier is
message is displayed in the cluster,
installed.
check to make sure that the rear
•
The vehicle drives in inclement
bumper is free from any dirt or snow
weather such as heavy rain or
in the areas where the sensor is
OOS057078L/OOS057079L
snow.
located. Remove any dirt, snow, or
foreign material that could interfere
Check Blind-Spot Collision
•
The sensor is polluted with rain,
with the radar sensors.
Warning (BCW) system
snow, mud, etc.
5
After any dirt or debris is removed,
If there is a problem with the BCW
•
The rear bumper where the sensor
the BCW system should operate nor-
system, a warning message will
is located is covered with a foreign
mally after about 10 minutes of driv-
appear and the light on the switch
object such as a bumper sticker, a
ing the vehicle.
will turn off. The system will turn off
bumper guard, a bike rack, etc.
If the system still does not operate
automatically. We recommend that
•
The rear bumper is damaged, or
normally have your vehicle inspected
you have your vehicle inspected by
the sensor is out of the original
by an authorized HYUNDAI dealer.
an authorized HYUNDAI dealer.
default position.
•
The vehicle height gets lower or
i
Information
higher due to heavy loading in the
luggage compartment, abnormal
Turn off the system by pressing the
tire pressure, etc.
BCW switch and deselecting Rear
•
When the temperature near the
Cross-Traffic Collision warning
(RCCW) from the User Settings mode
rear bumper area is high or low.
on the cluster, when using a trailer or
carrier behind your vehicle.
5-61
Driving your vehicle
•
When the sensors are blocked by
•
When the detected vehicle also
The BCW indicator on the outer
other vehicles, walls or parking-lot
moves back, as your vehicle drives
side view mirror may not illuminate
pillars.
back.
properly when:
•
The vehicle drives on a curved
•
While changing lanes.
•
The outside rearview mirror hous-
road or through a tollgate.
ing is damaged.
•
If the vehicle has started at the
•
The vehicle is driven near areas
same time as the vehicle next to
•
The mirror is covered with dirt,
containing metal substances such
you and has accelerated.
snow, or debris.
as a construction zone, railroad,
•
When the other vehicle passes at a
•
The window is covered with dirt,
etc.
very fast speed.
snow, or debris.
•
There is a fixed object near the
•
When the vehicle in the next lane
•
The window is tinted.
vehicle, such as a guardrail, per-
moves two lanes away from you
son, animal, etc.
OR when the vehicle two lanes
•
While going down or up a steep
away moves to the next lane to
road where the height of the lane is
you.
different.
•
The vehicle is turning left or right at
•
When driving through a narrow
a crossroads.
road with many trees or bushes.
•
A motorcycle or bicycle is near.
•
When driving on wet surfaces.
•
A flat trailer is near.
•
When driving through a large area
•
If there are small objects in the
with few vehicles or structures
detecting area such as a shopping
around, such as a desert, rural
cart, a baby stroller or pedestrian.
area, etc.
•
If there is a low height vehicle such
•
A big vehicle is near such as a bus
as a sports car.
or truck.
•
When other vehicles are close to
your vehicle.
•
When the other vehicle approach-
es very close.
5-62
FORWARD COLLISION-AVOIDANCE ASSIST (FCA) SYSTEM
- SENSOR FUSION TYPE (FRONT RADAR + FRONT CAMERA) (IF EQUIPPED)
The Forward Collision-avoidance
System setting and activation
WARNING
Assist (FCA) system is designed to
System setting
help detect and monitor the vehicle
Take the following precautions
• The driver can activate the FCA by
ahead or detect a pedestrian
(if
when using the Forward
placing the ignition switch to the
equipped) in the roadway through
Collision-avoidance
Assist
ON position and by selecting:
radar signals and camera recognition
(FCA) system:
to warn the driver that a collision is
"User Settings Driver assistance
imminent, and if necessary, apply
•
This system is only a supple-
Forward Collision-avoidance
emergency braking.
mental system and it is not
Assist (FCA)"
intended to, nor does it
replace the need for extreme
The FCA deactivates, when the driv-
care and attention of the driv-
er cancels the system setting.
er. The sensing range and
5
objects detectable by the sen-
sors are limited. Pay attention
The warning light illumi-
to the road conditions at all
nates on the LCD display,
times.
when you cancel the FCA
•
NEVER drive too fast in accor-
system. The driver can
dance with the road condi-
monitor the FCA ON/OFF status on
tions or while cornering.
the LCD display. Also, the warning
light illuminates when the ESC
•
Always drive cautiously to
(Electronic Stability Control) is
prevent unexpected and sud-
turned off. If the warning light
den situations from occur-
remains ON when the FCA is acti-
ring. FCA does not stop the
vated, we recommend that you have
vehicle completely and is not
the system checked by an authorized
a collision avoidance system.
HYUNDAI dealer.
5-63
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст