Dacia Solenza (engine E7J). Service manual — part 133
80
BATTERY - FRONT HEADLIGHTS
80 - 11
Disconnect the (-) plug of the battery;
Dismount the headlamp adjusting control from the turning lamp-headlamp assembly:
- pull backward the gasket of the headlamp adjustment corrector (1);
- detach from clips the protector (2) of the headlamp adjustment mechanism;
- loosen the locking nut (3);
- detach from clips the headlamp adjustment control cable (4) from the headlamp
adjustment corrector and then from the fork (5);
Dismount the headlamp adjusting control from the other turning lamp-headlamp assembly.
Detach from clips the headlamp adjustment control cables and cut the attachment collars.
Dismount the headlamps adjustment control button.
Dismount the attachment nut of the headlamp adjustment control on the dashboard.
Dismount the bonnet opening control cable from the opening handle (see chapter 52).
Detach from clips, by means of a straight screwdriver, the cables passing bushing from the
cowl panel.
Remove the headlamps adjusting control cables from the cowl-passing hole. Mark the mounting
position of the headlamps adjustment control cables.
REMOUNTING
Insert the headlamps adjusting control cables through the cowl-passing hole, observing the
existent position prior to dismounting.
Insert the bonnet opening control cable through the cables passing bushing.
DISMOUNTING
1
2
V
5 6 3 4
Replacement of the headlamps mechanic adjustment control
BATTERY - FRONT HEADLIGHTS
80
80 - 12
Replacement of the headlamps mechanic adjustment control
Attach on the cowl panel, by means of clips, the cables passing bushing, ensuring the cockpit
compartment sealing against possible water drain along the cables passing bushing.
Mount the bonnet opening control cable in the opening handle (see chapter 52). Position the
headlamps adjustment control on the dashboard.
Mount the attachment nut of the headlamps adjustment control on the dashboard.
Mount the headlamps adjustment control button and turn it in the position “3”.
Mount the headlamp adjustment control to a turning lamp-headlamp assembly :
- attach in clips by means of a straight screwdriver, the headlamp adjustment control cable
in fork (5) and then in the headlamp adjustment corrector;
- tighten initially the cable by hand till the fork (5) is in contact with support (6) so that fork
is remaining at max. 0.5 mm against the support;
- block the headlamp adjustment cable by means of the nut (3);
- attach in clips the protector (2) of the headlamp adjustment mechanism;
- position correctly the gasket of the headlamp adjustment corrector – the vertical adjustment
screw (V) must come out through the gasket.
Mount the headlamp adjustment control of the other turning lamp-headlamp assembly.
Attach in the attachment points, by means of clips, the headlamps adjusting control cables,
replace and mount the attachment collars, observing the mounting position prior to the dismounting.
Keep a distance of approximate 40 mm
±
10 mm between the right cable and the cylinder
no.1 spark plug cable, in order to avoid the loses due to electric-magnetic induction.
Reconnect the battery (-) terminal.
Switch on the headlamps and check the operation of the headlamps mechanic adjusting control.
The adjustment of the luminous spot dip of the headlamps in the downward sense of the vehicle
loading condition is to be performed by bringing the headlamps adjusting button in the “0” position
and then in the desired condition.
REMARK : The required tightening moment of the attachment nut of the headlamps
adjustment control on the dashboard: 2 Nm.
81
INSIDE AND REAR LIGHTING
81 - 1
REAR LAMPS
REAR LAMP REPLACEMENT
DISMOUNTING
Disconnect the battery (-) plug.
Disconnect the rear lamp connector .
Inside trunk, dismount the screw with triangle head (A).
Extract the rear lamp towards outside.
REMOUNTING
Perform the dismounting operations in the reverse order, positioning correctly the rear lamp in
its seat. Check the bulbs connections and operation.
Rear right lamp Rear left lamp
Rear right lamp connector
Rear left lamp connector
Pin
Denomination
Pin
Denomination
1
+ Right stop lamp
1
Fog parking lamp supply
2
+ Right parking lamp
2
Left turning lamp supply
3
Free
3
Free
4
Mass
4
Mass
5
Right turning lamp supply
5
+ Left stop lamp
6
Revere driving lamp supply
6
+ Left parking lamp
Inside and rear lighting
A
6
1
B
B
B
B
6
1
INSIDE AND REAR LIGHTING
81
81 - 2
REPLACEMENT OF REAR TURNING,
PARKING, FOG, REVERSE DRIVING,
STOP BULB
DISMOUNTING
Disconnect the battery (-) terminal.
Disconnect the rear lamp connector
Dismount the screw with triangle head
Extract the rear lamp towards outside
Dismount the two attachment screws (B) of
the bulbs support on the lamp glass.
Dismount the worn bulb.
REMOUNTING
Perform the dismounting operations in the
reverse order, checking the condition of the
sealing gasket between the lamp glass and the
bulbs support: if this one is not good, replace it.
Check the bulbs operation and connections.
REPLACEMENT OF LICENSE PLATE
LAMP BULB
DISMOUNTING
Disconnect the battery (-) terminal.
Disconnect the license plate lamp connector.
Extract the license plate lamp holder.
Remove the worn bulb and replace it.
REMOUNTING
Perform the dismounting operations in the
reverse order. Check the bulb operation.
REPLACEMENT OF ADDITIONAL
STOP LAMP BULB
DISMOUNTING
Disconnect the battery (-) terminal.
Dismount the TORX 20 attachment screw
of the additional stop lamp. Mark the mounting
position of the lamp mass wire connector.
Inside and rear lighting
Disconnect the additional stop lamp
connector.
Detach the two side clips and extract the
reflector-glass assembly from the lamp body.
Detach carefully from clips the lamp glass,
by means of a straight screwdriver.
Replace the worn bulb.
REMOUNTING
Perform the dismounting operations in the
reverse order. Check the bulb connections and
operation.
REPLACEMENT OF LICENSE
PLATE LAMP
DISMOUNTING
Disconnect the battery (-) terminal.
Disconnect the license plate lamp
connector.
Detach from clips the license plate lamp.
REMOUNTING
Perform the dismounting operations in the
reverse order. Check the bulb operation.
REPLACEMENT OF ADDITIONAL
STOP LAMP
DISMOUNTING
Disconnect the battery (-) terminal.
Dismount the attachment screw TORX 20
of the additional stop lamp. Mark the mounting
position of the lamp mass wire connector.
Disconnect the additional stop lamp
connector.
REMOUNTING
Perform the dismounting operations in the
reverse order.
Check the bulb connections and operation.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст