Dacia Solenza (engine E7J). Service manual — part 132
80
BATTERY - FRONT HEADLIGHTS
80 - 7
FRONT TURNING BULB REPLACEMENT
DISMOUNTING
Disconnect the connector (3).
Rotate the holder (4) and remove it.
Remove the worn bulb from the holder
REMOUNTING
Perform the dismounting operations in the reverse order, with the checking of the correct
holder (4) positioning to avoid dust and humidity penetration in the headlamp assembly.
The turning lamps are using orange color bulb; when replacing the bulb, use the same bulb
type.
FRONT PARKING BULB REPLACEMENT
DISMOUNTING
Rotate the holder (5) and remove it.
Extract the worn bulb from the holder.
REMOUNTING
Perform the dismounting operations in the reverse order, with the checking of the correct
holder (5) positioning to avoid dust and humidity penetration in the headlamp assembly.
Bulbs
BATTERY - FRONT HEADLIGHTS
80
80 - 8
HEADLAMP-FRONT LAMP ASSEMBLY SEALING
(getting fogged, it has condensation water or water penetration)
The condensation water is not affecting the lighting quality.
No
No
No
No
No
Yes
Yes
Yes
Yes
Bulbs
Check the front part of the assembly: direct
a water jet towards the headlamp glass.
Is the water penetrating inside the headlamp?
Is water penetrating inside the parking-turning
lamp?
Visually check the headlamp rear part; rubber
protector of the headlamp bulb is correctly
mounted?
The headlamp adjustment corrector is well
mounted?
The headlamp bulb is correctly mounted?
The aeration holes are clogged?
The hea dlamp is steamed out or it has
condensation water inside?
Visually check the rear part of the parking-
turning lamp; the parking bulb holder is
correctly mounted?
The turning bulb holder is correctly mounted?
Replace the headlamp.
Replace the parking-turning lamp.
Mount correctly the rubber protector of the
headlamp bulb. If this is not good, replace it.
Mount correctly the headlamp adjustment
corrector and its rubber protector. If protector
is not good, replace it.
Mount correctly the headlamp bulb.
If possible, eliminate the clogging cause. If
not possible, replace the headlamp.
Explain the client that this fact is a natural
one, not a damage and there is no headlamp
corrosion risk. The condensation water will
disappear when the headlamp will be lighted;
the disappearing time of the condensation
water is subject to the environmental
humidity.
Mount correctly the parking bulb holder. If
its gasket is not good, replace it.
Mount correctly the turning bulb holder. If
its gasket is not good, replace it.
REMARK : If the client is insisting, proceed to headlamp drying:
- blow with dry air, if possible;
- naturally dry the headlamp by turning on the headlamps for couple of minutes
till condensation water elimination or headlamp defogging.
No
No
No
No
Yes
Yes
Yes
Yes
80
BATTERY - FRONT HEADLIGHTS
80 - 9
MEETING LIGHTS ADJUSTMENT (LOW BEAM)
This is performed by acting upon the V screw
(vertically plane adjustment) or H (horizontally
plane adjustment). By screwing, the lighting beam
is ”lowering” and by unscrewing is “ascending”.
Check if the lighted area is centered on the
vertical axis and if the optical separation at 15°
coincide with the headlamp lighting. An error of
1 cm is admissible.
A lighting beam displaced towards left has
the aspect shown in (picture a) and a lighting
beam displaced towards right has the aspect
shown in (picture b)
ROAD LIGHTS ADJUSTMENT (LONG BEAM)
Check the position to coincide with the
adjustment performed for low beam and with
the lighting beam distributed between the two
vertical lines on the panel
When checking the long beam, the lighting
center of the ellipse, must be located on the
cross marking the screen center.
If a major deviation compared with the low beam is noticed, it is recommended the bulb
replacement, this one being in most of the cases, responsible for such defect.
Headlamps adjustment
H
V
figura a
figura b
BATTERY - FRONT HEADLIGHTS
80
80 - 10
FOG PROJECTORS ADJUSTMENT
The fog projectors adjustment is to be performed in the following conditions:
-
the vehicle to be placed on a horizontal surface;
-
the vehicle has not passengers inside the cockpit or weights in the trunk;
-
the tires are pressurized at the manufacturer prescribed pressure.
Further on, proceed as follows:
Bring the vehicle at the working place.
Position the adjustment device (headlamp adjustment device –E) in front of an optical center
of a fog lamp.
Switch on the fog projectors. Rotate the adjustment screw of the fog lamp (D), by means of
a screwdriver (A), so that an adjustment of 2 % is obtained and the separation between the
lighted area and the dark one from the adjustment device is located under the marked line (G)
This adjustment is to be performed in the same way as for the meeting lights adjustment.
Bring the adjustment device in front of the optical center of the second fog lamp;
Perform the fog projector adjustment;
Switch off the fog projectors.
Headlamps adjustment
G
E
A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст