Dacia Solenza (engine E7J). Service manual — part 6
VALUES AND ADJUSTMENTS
07
07 - 8
Checking values of the front axle angles
ADJUSTMENTS
Not adjustable
Not adjustable
Not adjustable
Adjustable by
rotating the tie
rod of the
steering rod
-
VEHICLE
POSITION
H5 - H2 = 100
H5 - H2 = 90
H5 - H2 = 80
H5 - H2 = 70
H5 - H2 = 60
H1 - H2 = 105
H1 - H2 = 98
H1 - H2 = 91
H1 - H2 = 85
H1 - H2 = 78
H1 - H2 = 71
H1 - H2 = 64
H1 - H2 = 105
H1 - H2 = 98
H1 - H2 = 91
H1 - H2 = 85
H1 - H2 = 78
H1 - H2 = 71
H1 - H2 = 64
Not loaded
Not loaded
VALUES
0
0
03'
0
0
20'
0
0
36'
± 30'
0
0
53'
1
0
10'
Right / left maxim
difference = of
1
0
-0
0
16'
-0
0
10'
-0
0
02'
0
0
06'
± 30'
0
0
15'
0
0
24'
0
0
35'
Right / left maxim
difference = of
1
0
13
0
36'
13
0
25'
13
0
14'
13
0
03'
±30'
12
0
50'
12
0
38'
12
0
24'
Right / left maxim
difference = of
1
0
Toe in:
0
0
10' ± 10'
(for one wheel
0
0
05' ± 05')
-
ANGLES
CAMBER
CASTER
BALL JOINT
TOTAL PARALLELISM
ELASTIC BUSHINGS
TIGHTENING
VALUES AND ADJUSTMENTS
07
07 - 9
Checking values of the rear axle angles
ADJUSTMENTS
Not adjustable
Not adjustable
VEHICLE
POSITION
Unloaded
Unloaded
Unloaded
VALUES
0
0
30' ± 10'
(For two wheels)
Closing
0
0
30' ± 10'
2,9 mm ± 1 mm
ANGLES
CAMBER
PARALLELISM
ELASTIC BUSHINGS
TIGHTENING
PRELIMINARY OPERATIONS TO BE OBSERVED BEFORE
CHECKING THE STEERING ANGLES
1. Area (checking surface) – it must be as horizontal as possible.
2. Wheels, tires – check (from equipping point of view) to have same type of wheels and
tires on both axles (dimensions, inflating pressure, wear degree). A pronounced wear is not
allowing the correct horizontal positioning.
3. Suspension – check the shock absorbers, springs condition and height symmetry under
carriage body.
4. Joints – check the elastic joints condition, steering and suspension ball joints clearance,
bearings clearances of the front and rear axles
5. Radial and axial run out of the wheels – must not be over 1 mm. This will be compensated
with the reading instruments.
6. Manufacturer’s method – each vehicle manufacturer is providing the checking conditions,
axles weights repartition, and presentation of under carriage body heights, not loaded.
ENGINE
E7J-262
10
ENGINE ASSEMBLY
10 - 1
Ingredients
TYPE
RHODORSEAL 5661
Loctite FRENETANCH
COMPONENTS
Lower crankcase sealing
Crankshaft pulley attachment screw
IDENTIFICARE
The engine identification is achieved by means of a metallic plate stuck on the engine block.
Markings on metallic plate:
A – engine type
B – engine homologation letter
D – “RENAULT” identification code
E – engine index
G – code for engine assembling factory.
F – engine manufacturing series
Loctite 518
Water pump, thermostat support, crankshaft
closing casing, crankshaft no.1 bearing cover
Engine oil DACIA OIL
EXTRA 10 W40; API SJ
Engine lubrication
Decapjoint
Cleaning of the aluminum parts surfaces
Vehicle
type
Engine
Gearbox Cylinder
capacity
(cm
3
)
Bor e
(mm)
Stroke
(mm)
Volume
ratio
Dacia
SOLENZA
E7J-262
JH3 - 051
1390
75.8
77
9.5/1
De-pollution
norm
EU 96
EU 00
E7J-262
E7J-262
1504
MA
MB
MC
000 0 0 / 00
0 000000
A B D E
G F
ENGINE E7J-262
10
ENGINE ASSEMBLY
10 - 2
OIL CONSUMPTION MEASURING
a) Oil filling to maximal level
This operation is to be performed when the engine is warm (one engine fan rotation) and after
a stabilization of 15 minutes, necessary to the oil complete draining into the lower crankshaft.
Check the oil at the oil-indicating rod.
Fill to the maximal level.
Seal the draining and filling taps (mark them with paint), for further checking if these have not
been dismounted
b) Customer driving time
Ask the customer to drive for about 2000 km or until the oil reaches the minimal level.
c) Refilling to the maximal level
This operation is to be performed when the engine is warm (one engine fan rotation) and after
a stabilization of 15 minutes.
Check the oil at the oil-indicating rod.
Fill to the maximal level.
Write down the oil quantity and the driven mileage after filling to the maximal level.
d) Oil consumption measuring
Oil filled quantity (liter)
OIL CONSUMPTION =
kilometers (thousand)
Oil consumption
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст