Dacia Solenza (engine E7J). Service manual — part 104
47 - 01
47
Rear door
Front door
LATERAL OPENINGS
DISMOUNTING
Dismount the elements, which are in connection with the front/rear door.
Dismount the door panel.
Dismount the door wiring protected by sleeve (1) and remove it through the existent door
caisson hole.
Dismount the attachment screw (2) of the limiting mechanism of the front/rear door.
Dismount the upper hinge axle (3) and lower hinge axle (4).
REMOUNTING
Perform the dismounting operations in the reverse order.
Grease the hinges with white grease (Teroson).
48
NON – LATERAL OPPENINGS
48 - 1
Front bonnet
DISMOUNTING
Dismount :
- attachment screws (1) and (2) of the
upper half-hinges on the front bonnet lining;
- front bonnet.
REMOUNTING
Pre-attach the screw (1) from the
windscreen frame on the front bonnet lining
(left/rig
ht).
Place the front bonnet in the upper half-
hinge (through the channel made in it) and
adjust the clearances.
Mount the other two attachment screws
of the upper half-hinges on the front bonnet
lining and tighten all the four screws to the
required moment of 22,44 Nm.
Grease the hinges with white grease
(Teroson).
NON – LATERAL OPPENINGS
48
48 -2
Hatchback
DISMOUNTING
Dismount the hatchback wiring (1) and
remove it through the existent hole in the
hatchback lining.
Dismount :
- safety locks (2) of the balancing shock
absorbers on the hatchback
- attachment screws (3) of the balancing
shock-absorbers on the hatchback;
- attachment screws (4) of the hinges on
the hatchback;
- hatchback.
REMOUNTING
Perform the dismounting operations in the
reverse order.
Grease the hinges with white grease
(Teroson).
3
4
1
2
51
51 - 1
MECHANISMS OF LATERAL OPENINGS
Front door-opening mechanism with electric control
1
2
13
TIGHTENING MOMENTS (daNm)
Attachment screw of assembled box 1.1
Mechanism bolt 5
Attachment screw of outside opening
mechanism 0.5
DISMOUNTING
Disconnect the battery (for vehicles
equipped with central locking mechanism).
Dismount:
- window lifting crank, by detaching it
from the crank axle (for vehicles without electric
windows regulator).
- attachment screw (2) of the inside
opening mechanism (1);
- closing handle (13);
- front door panel (see chapter 72);
- front door deflective panel.
Dismount the lock fork (13) from the
electric control latch.
Disconnect the actuator connector (7).
Remove the opening control rod of the front
door (3).
Dismount the attachment screws (5) of the
assembled box (4) from the front door caisson.
Remove the electric control latch (6) through the
technological opening from the front door caisson.
Dismount:
- attachment screws (10) of the outside
opening mechanism (9) on the door external panel;
- mechanism bolt (12);
- screws (8) attaching the actuator (7)
to the electric control latch (6).
REMOUNTING
Perform the dismounting operations in the
reverse order, taking into account the follow-
ing recommendation:
- actuator attachment on the latch is to
be performed so that its acting stroke is of
minim 18 mm;
- for the front door latch mounting, the
connecting fork (11) of the outside opening
mechanism will be fixed on the existing ball joint
on the lock;
- all springs, rivets and elements that are
in movement are to be lubricated with UM 185
Li2 grease;
- for the latch attachment screws to the
electric control, product Fixamed M28 is to
be used;
- front door deflective panel is to be fixed
on the caisson by means of a sealing material
Romtix 1502 P;
- adjustment of the front door closing is
to be performed by means of the mechanism
bolt (12), that is to be tighten to the required
moment of 5 daNm.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст