Dacia Solenza (engine E7J). Service manual — part 148
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 49
Diagnostic – General
THE PROCEDURE OF
KEYS ASSIGNATION
IMPORTANT
: if not all keys are available it
will be necessary to subsequently perform the
assignation procedure with all the keys.
Ente r in dialogue with syste m “A nti-
starting”.
In
menu ”Control menu”, “Specific
control”, validate line “SC028: Key program-
ming”.
Tester is displaying: “Take off the key from
anti-theft contact”.
Tester is displaying “Enter the after-sale
code”.
With contact set off, enter the after-sale se-
cret code (12 hexadecimal characters) and vali-
date it.
Tester is displaying “Attention. Not pre-
sented keys will be not active. Re -launch
the procedure in order to re-assign them”:
the programming is under way.
Tester is displaying: “Insert key in anti-
theft contact and set the contact on, then
validate”: set the contact on using a vehicle key
or a new key.
Tester is displaying: “No of programmed
keys 1” and “ take off the key from anti-
theft contact, then validate”.
Tester is proposing: “Do you wish to pro-
gram a new key ?”.
In order to assign additional keys, set the con-
tact on few seconds using the vehicle’s others
keys that must be assigned (maximum four), then
validate.
Tester is displaying: “2, 3, 4 programmed
keys” and “ take off the key from anti-theft
contact”.
ATTENT ION: these ones must be the
vehicle’s old keys or new not coded keys.
Tester is displaying: “ Data entry in memory”,
Cockpit Central Unit is coded and the keys are
assigned.
This message will be displayed for few
seconds, then you may come out from the re-
assignation procedure
ATTENTION: the maximum admissible
interval between each operation is of 5 min-
utes otherwise the procedure is canceled.
Tester is displaying in this situation the
me ssa ge : “Pe r for ming conditions not
ac c omplishe d”. T his me ssa ge is a lso
displayed in case of dialogue loss with the
Cockpit Central Unit or in case of battery
supplying cutting off.
SPECIAL SITUATIONS
If tester is displaying:
“Cockpit Central Unit is empty. Launch
the C ockpit Central Unit programming
procedure”, then the Cockpit Central Unit is
not used. It is impossible to assign keys to a
not coded Cockpit Central Unit.
“Per forming conditions not accom-
plished”, the entere d code is not correct;
check and then start again the code entering
procedure.
If the key does correspond to the Cockpit
Central Unit of that vehicle, the tester is dis-
playing “Interrupted procedure: attention,
the keys assigned to the vehicle are the
ones that have been assigned before pro-
cedure starting. The pr esented keys be-
fore procedure interruption are not any-
more empty and can be only assigned to
this vehicle” assigned.
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 50
Diagnostic – General
THE PROCEDURE OF KEYS’ ASSIGNATION
Enter in dialogue with the
system “Anti-starting”
Select menu
“ Control module” and
“Specific control”.
Validate line “SC 028:
Key programming”.
Tester is displaying: “
take off the key from
anti-theft contact”
Tester is displaying Enter
The after-sale code”.
Enter the code (12
hexadecimal characters
with capitals) then validate it
A
The procedure must be performed
only when contact is set off.
If tester is displaying:
“Cockpit Central Unit is
empty Launch the Cockpit
Central Unit programming
procedure”.
Tester is displaying
“ Performing conditions
not accomplished ”.
Cockpit Central Unit is new.
It is impossible to assign the
keys to a Cockpit Central
Unit not coded.
The entered code is wrong or
it s not correct.
Check and re-enter the code.
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 51
Diagnostic – General
Tester is displaying: “Attention.
The non presented keys
shall be not
active. Re-launch the procedure in
order to re-assign them”.
Tester is displaying: “ Insert
key in anti-theft contact, set
contact on, then validate”.
Insert a key in anti-theft con-
tact. The key must be new or
belonging to this vehicle.
This procedure is enabling the
decommissioning of one key in
case of its loss, for instance
Tester is displaying: 1 key
Programmed”, “Take off the
key from anti-theft contact,
then validate”.
Tester is displaying: “ Do you
wish to program another key?”
Insert another new key or
belonging to this vehicle in
the anti-theft contact.
Tester is displaying: “ 2,3,4 keys
programmed
” then “T
ake off the
key from the anti-theft contact, then
validat
e”.
Tester is displaying: “ Data
entry in memory”.
The keys are assigned to the
vehicle. Check if the vehicle is
starting and if the doors get
blocked by means of all keys
If tester is displaying:
“Interrupted procedure: at-
tention, the vehicle’s as-
signed keys are those that
were assigned before the
procedure launching. The
keys presented before the
procedure interruption are
not anymore empty and can
be assigned only to this ve-
hicle”.
The vehicle may use
maximum 4 keys.
The key does not
correspond to the
UCH of this vehicle
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 52
Diagnostic – General
THE CODING OF THE INJECTION COMPUTER.
The injection computer is delivered not coded. Therefore, the anti-starting system code
memorizing will be necessary, when its mounting, in order to authorize the vehicle starting.
It is sufficient to set the contact on for few seconds, without starting the engine. Set the
contact off and the anti-starting function will be ensured after few seconds (anti-starting red
LED is blinking)
ATTENTION:
By means of this anti-starting system, the vehicle is keeping its own anti-starting code on all
its lifetime. Furthermore, this system does not have a breakdown code. Therefore, it is forbidden
to perform tests with injection computers borrowed from warehouse that must be after that
returned. The code memorized by the injection computer can not be anymore erased.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст