SsangYong Stavic / SsangYong Rodius (2005 year). Service manual — part 395
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
3
PROPELLER SHAFT
STAVIC - 2004.09
4I
Structure
Joint type
Number of spiders
Outer diameter of spider (mm)
Tube run-out (after installation)
Unbalance
Front shaft dimension
Length x Outer diameter (mm)
Rear shaft dimension
Length x Outer diameter (mm)
The propeller shaft transfers the power through the transmis-
sion and transfer case to the front/rear axle differential carrier
(final reduction gear). It is manufactured by a thin rounded
steel pipe to have the strong resisting force against the torsion
and bending.
Both ends of propeller shaft are connected to the spider and
the center of propeller shaft is connected to the spline to ac-
commodate the changes of the height and length. The rubber
bushing that covers the intermediate bearing keeps the bal-
ance of rear propeller shaft and absorbs its vibration.
1. GENERAL INFORMATION
Yoke and spider type universal joint
Spider (Needle roller bearing)
1
2
φ 17.893
below 0.4 mm
Below 14.5 g.cm @ 4500 rpm (Front shaft + Full time T/C)
Below 18.0 g.cm @ 4500 rpm (Rear shaft + Full time T/C)
M/T(A/T) + 4426 TC (TOD)
DI engine + M/T(A/T) + 4426 TC (TOD)
DI engine + M/T + 2WD
DI engine + A/T + 2WD
Gasoline + M/T + 2WD
Gasoline + A/T + 2WD
Specification
Front
Rear
TOD T/C
Description
Specification
495.8 (center position) x
φ 50.8 (3.05t)
606.1 (compressed) x
φ72.2(2t)
+ 769.5 x
φ 76.2 (2t)
923.5 x
φ 63.5 (2t)
+ 750.4(compressed) x
φ 63.5 (2t)
987.7 (compressed) x
φ 63.5(2t)
+ 769.5 x
φ 63.5 (2t)
923.5 x
φ 76.2(2t)
+ 750.4 (compressed) x
φ 63.5 (2t)
987.7 (compressed) x
φ 76.2(2t)
+
769.5 x
φ 63.5 (2t)
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
4
PROPELLER SHAFT
STAVIC - 2004.09
4I
2. COMPONENTS AND LOCATION
Front Prepeller Shaft Assembly
Rear Prepeller Shaft Assembly
Bolt
Bolt
CV joint
Front propeller shaft assembly
Universial joint
Bolt/washer/nut
Universial joint
1st rear propeller shaft
Center bearing assembly
CV joint
2nd rear propeller shaft
Bolt
Universial joint
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
5
PROPELLER SHAFT
STAVIC - 2004.09
4I
3. REMOVAL AND INSTALLATION
Removal
Front Propeller Shaft (4WD)
* Leave a guide mark before
disassembly, and refer to
the mark when reinstall
1. Unscrew propeller shaft mounting bolts and remove the shaft from the vehicle. (T/C : 17 mm - 4EA, Axle : 14 mm
- 4EA)
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
6
PROPELLER SHAFT
STAVIC - 2004.09
4I
Rear Propeller Shaft
2. Unscrew the rear propeller shaft center bearing
mounting bolts (17 mm - 2 EA)
Axle side
T/C side
Center bearing
* Leave a guide mark
before disassembly,
and refer to the mark
when reinstall.
1. Unscrew propeller shaft mounting bolts. (T/C : 17 mm -
4EA, Axle : 14 mm - 4EA)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст